Search Documents

By Herbert P. Haschke

I. Changes made by the Economic Recovery Tax Act of 1981 (ERTA) which have an effect on investing in tax shelter investments A. Maximum ordinary income tax rate on individuals is now 50%. B. Maximum tax rate on long-term capital gains for individuals is now 20%. C. Maximum tax rate on alternative minimum taxable income for individuals is now 20%. D. Although not changed, the "add-on" 15% minimum tax on tax preference items and the possibility of paying the alternative minimum tax cause individual U.S. income tax planning to continue to be very complex. II. Real Estate A. The new Accelerated Cost Recovery System of depreciation (ACRS). 1. Mandatory for assets placed in service after 1980. ACRS will eliminate most if not all controversies with the IRS over depreciation. 2. Real property now depreciated over 15 years. Component depreciation is not available. 3. Accelerated depreciation is available - a 175% declining balance method with an automatic shift to straight line method at the optimum point in the asset's life. Alternatively, a taxpayer can elect to use the straight line method.

Jan 1, 1982

By J. N. Eskilsson, W. P. Chen, J. L. Kaplin, V. S. Romero

The Massachusetts Water Resources Authority is currently improving its primary water supply system for the Boston Metropolitan area. The improvements planned by the Authority, which provides water for 46 communities and over 2.5 million people in eastern Massachusetts, include the MetroWest Water Supply Tunnel (MWWST) to provide redundancy in the transmission system, a large capacity water treatment plant and extensive covered storage facilities. The 28.3 km (17.6 miles) long, mostly 4.3 m (14 ft.) I.D. MetroWest Water Supply Tunnel will allow repair of the aging Hultman Aqueduct, which for 56 years has served as the transmission main from the water supply reservoirs to Boston. On completion of the tunnel, the old pipeline aqueduct will be repaired and brought back into service as a parallel, redundant transmission main. This paper describes design considerations and the design process for pressure tunnels in general and the MWWST in particular. It provides an overview of how the design of pressure tunnel and shaft components progresses.

Jan 1, 1997

One of the core tenets of Sustainable Development is transparency and information sharing, i.e., government and corporate reporting. Governments report on issues within their sphere of responsibility to the degree that their constituents demand that they do so. Firms undertake reporting for two reasons: they are required to do so by law, and doing so makes good business sense. In recent years, stakeholders have come to see themselves as having a right to information about government actions and business operations that have the potential to affect their lives, health, community and environment. As a result, disparate groups, including industry associations, non-profit groups, academics, and individual firms, attempted to lay out what governments and firms should report. There are many types of sustainability reporting. In this paper we focus on three of them that both governments and firms utilize. We discuss the benefits of each. We argue that while the goal of complete and perfect data is not achievable or feasible, sustainability reporting of all three types is necessary to ensure that sound public and private decisions are made.

Jan 1, 2007

By C. J. Pritchard

I commend the authors on examining an interesting method of shaft lining and attempting to improve safety in a dangerous environment by remotely installing the shaft lining. It is important, though, to not trade off shaft lining safety for long-term mine safety by lining an intake shaft with combustible material. In many operations, the mine utilities are installed next to the lining of the intake shaft, supplying a possible ignition source if damaged or overloaded. Although the polyurethane studied in the paper is of relatively high density, no mention is made of the flame retardency of the samples. When exposed to heat, small amounts of polyure¬thane will melt and bum but are extinguished when the heat source is removed. If large surface areas of combustible polyurethane - a tunnel or mine shaft - are exposed to ignition heat sources that are not removed or extinguished early, an uncontrollable, fuel rich fire may result with high carbon monoxide levels, low oxygen concentrations, and greatly increased burning rates that can have devastating effects on the ventilation system and miners' safety.

Jan 1, 1990

By Don Rose

I. INTRODUCTION The Atlanta Research Chamber is an UMTA-sponsored applied research facility studying tunnel design, excavation and support systems. It is located directly below Peachtree Street in downtown Atlanta, Georgia. It is included in the CN-120 contract to build the Peachtree Center subway station, a part of the Metropolitan Atlanta Rapid Transit Authority (MARTA) multi-billion dollar "Phase A" 53-mile transit project, which is 80 percent funded by UMTA with 20 percent provided by local authorities in Atlanta and Fulton and DeKalb counties (Figure 1). The Research Chamber is located immediately south of the main Peachtree Center Station cavern, and is in part an enlargement of the pre-existing Pilot Tunnel excavated to provide bidders on the CN-120 contract a view of the rock conditions (Figure 2). The Research Chamber lies some 3 meters above, and is approximately parallel to, the twin Running Tunnels. The Research Chamber is 18 meters long and has the same 5.5 meter diameter horseshoe shape design dimensions as the twin Running Tunnels.

Jan 1, 1979

By G. E. Erdman

This paper presents talc milling guided by a theme of "So You Want to Be In The Talc Business". Such a theme strikes a cautionary note to warn the uninitiated of potential pitfalls, and this paper will cover briefly some of the technical traps as well as one of the larger talc milling operations. It is important to our purpose to pre- sent some of the market and mineral complications that make the business of producing and selling industrial talcs much more intricate than an outsider would perceive. Metal markets by comparison are great worldwide pools into which production streams of generally identical metals can flow over a weir of market prices. Industrial talc markets are not as well defined and often must be developed by the producer working closely with a specific customer or groups of customers to prove out the attributes of the specific product from a new property. All the negatives of a new market seem to work against the introductory talc in the forms of industry or customer reluctance to change, sales prices, cost of delivery, mode of transportation, health considerations of the minerals and many more. Just locating the potential customers for a new industrial talc may be a substantial undertaking. Thus, an analogy of the worldwide metal market might compare starting a new talc operation to trying to gather up enough fallen rain drops to be able to start a production stream of a worthwhile size.

Jan 1, 1984

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, violations are often the most frequent form associated with accidents. These occur when an individual, or individuals, deliberately contravenes established and known safety rules. They have been associated with up to 90% of accidents and incidents in some industries and yet rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives which cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of attitudes to determine the underlying motives behind violations if they are to determine effective strategies for promoting safe behaviour. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, however, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 1998

By E. J. Garrison

Discussion by E.J. Garrison A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent. Reply by A.C. Noble E.J. Garrison asserts that I confuse the difference between a resource and an ore reserve. In fact, this paper was motivated by the observation that resources and reserves are almost universally confused throughout the industry. While Garrison is concerned that too-early consideration of engineering, metallurgical and economic factors will result in dropping properties too soon, some issues that must be considered include: •The purpose of exploration is to discover ore reserves, not to discover resources. •Ore reserves are always smaller than resources. • Decisions on exploration expenditures must be made based on the expectation of the quantity of ore reserves that will ultimately be defined. Noble's Fig. 2 can be used to give guidance as to when it is appropriate to begin reserve calculations. When exploration enters the "flat" portion of the curve, representative samples can be selected for metallurgical studies and appropriate mining methods chosen. It is at this stage that we know enough about the deposit to make intelligent choices of representative samples and recognize constraints on mining caused by the deposits shape, environment and physical properties. Once the appropriate technologies have been chosen, then their cost can be estimated with reasonable accuracy. Early entry of economic and process factors gives the false appearance of reserve status to the resource estimation. It would be more informative and less subject to abuse and misunderstanding if resource calculations were made at a number of cutoff grades. The cutoff grades should be chosen to cover the range of grades found in practice in existing operations of similar type. This would emphasize the open nature of resource estimates and encourage creative evaluation of mining and process technologies. It does not preclude the use of economic, environmental and recovery technology factors in deciding the advisability of continuing exploration expenditures, but would highlight their speculative nature. It is thus hoped that decisions on the future of the deposit would not be made on the presumed suitability of a given technology but on the actually known reality. I agree that resource estimates should be reported as a range of cutoff grades. Since reporting at a cutoff implies application of underlying economics (even by analogy to similar properties), however, it should be clearly stated that resources do not consider economic, mining or cost factors, and that ore reserves will be substantially less. The dilemma of the explorationist is that until the continuity and limits of ore-grade mineralization have been established, it is difficult to make quantitative estimates of either resources or ore reserves. Further industry discussion is needed regarding standards for disclosing early exploration information in such a way as to fairly represent the potential of an exploration property.

Jan 1, 1995

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Event cameras are used for their performance in high dynamic-range lighting conditions which are canonical to active mining environments. Direct labeling of event-based image data to train a model to perform semantic segmentation using traditional methods is slow and error-prone. This study proposes a framework to use roughly hand-labeled color images from a mine as an input to an intermediary probabilistic algorithm called alphamatting to generate a ground-truth data set. These high-fidelity labels can be used to train a semantic segmentation model to differentiate the support strap from the roof. This model can then be leveraged to segment an event-based scene to enable autonomous roof bolting. This pipeline has been shown to achieve an accuracy of 88% with a false positive rate of 3%.

Feb 1, 2024

By G. Frey, D. Scott, C. Pritchard

Controlled recirculation has been used in the metal/nonmetal mining industry for energy savings when heating and cooling air, in undersea mining and for increasing airflow to mining areas. For safe and effective use of controlled district recirculation, adequate airflow to dilute contaminants must exist prior to implementation, ventilation circuit parameters must be accurately quantified, ventilation network modeling must be up to date, emergency planning scenarios must be performed and effective monitoring and control systems must be installed and used. Safety and health issues that must be considered and may be improved through the use of controlled district recirculation include blasting fumes, dust, diesel emissions, radon and contaminants from mine fires. Controlled recirculation methods are expected to become more widely used as mines reach greater working depths, requiring that these health and safety issues be well understood. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted two controlled recirculation tests over three days at a Wyoming trona mine, utilizing an inline booster fan to improve airflow to a remote and difficult-to-ventilate development section. Test results were used to determine the effect that recirculation had on air qualities and quantities measured in that section and in other adjacent areas. Pre-test conditions, including ventilation quantities and pressures, were modeled using VnetPC. During each test, ventilation quantities and pressures were measured, as well as levels of total dust. Sulfur hexafluoride (SF6) tracer gas was used to simulate a mine contaminant to monitor recirculation wave cycles. Results showed good correlation between the model results and measured values for airflows, pressure differentials, tracer gas arrival times, mine gasses and dust levels.

Jan 1, 2013

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022

By Frederick B. Henderson

The US Environmental Protection Agency (EPA) has tried many regional and laboratory efforts to develop measurement and monitoring techniques using environmental remote sensing technologies. In 1997, the agency established the Advanced Measurement Initiative (AMI): This is a eadquarters-level program, operating under the auspices of the EPA Office of Research and Development. The program is one result of the April 30,1996 White House Conference on Advanced Monitoring of the Environment. The EPA was encouraged to work with other federal agencies to leverage its remote sensing capabilities and use them to improve the efficiency, cost-effectiveness and flexibility of environmental measurement and monitoring for regulatory compliance and reinvention. During the fall of 1996, the EPA and the Department of Energy developed an interagency effort to broaden the use of governmental technologies for environmental measurement and monitoring. In addition, the EPA and the National Aeronautics and Space Administration (NASA) conducted joint workshops on the use of NASA remote sensing and other technologies for water quality and pollution applications. In the meantime, the EPA proceeded with an industry-proposed workshop to explore ways to cooperatively examine new research and to develop commercial remote sensing systems. It also examined how these systems might become accepted by the EPA in the regulatory and compliance processes. In particular, industry was interested in where new remote sensing capabilities might fit in with EPA's efforts at regulatory reinvention. Historically, the mining and petroleum industries have been reluctant to experiment with or use environmental remote sensing. They were concerned with the unknown liability from potential discovery of previously unknown environmental problems. Moreover, resource industries have been reluctant to use remote sensing for environmental applications where the EPA did not accept such data or information as part of the compliance process. Acceptance by the EPA of these advanced measurement and monitoring technologies (AMMT) will be a major reason for industry's increasedd use of remote sensing in environmental "applications for regulatory compliance. In July 1997, the EPA Office of Research and Development hosted at the Colorado School of Mines a stakeholders workshop on the AMI program and industry-government collaboration. The workshop's aim was to demonstrate the usefulness of AMMT technologies for environmental applications. Stakeholders included the mining and petroleum industries; environmental services companies; state environmental agencies and local governments; remote-sensing, value-added companies and data suppliers. The workshop used specific technologies and applications as a way to develop collaborative demonstration projects for several AMMT technologies covering different environmental problems. The workshop focused on the use of highly sensitive hyperspectral (very narrow spectral bands), geographic information systems and surface mapping to identify active acid-producing mine dumps and wastes from benign wastes at Leadville, CO. NASA's advance infrared imaging spectrometer (AVIRIS) was the instrument used. It was developed at California Technology's Jet Propulsion Laboratory. The EPA, the US Bureau of Land Managment (BLM), the US Geological Survey and several environmental service contractors sponsored the overflight and data evaluation. The AVIRIS study demonstrated reliability (95% correct surface mineral identification) and cost-effectiveness of this technology to accurately map and discriminate active acid-producing mine wastes from benign wastes. It could also predict which streams would be effected by acid and toxic mineral drainage. The BLM'said that the AVIRIS overflight could save it $500,000 a year in surface sampling costs at Leadville. The AMI workshop further outlined five 1997 funded AMI projects of potential interest to the mining industry. They were: ? Mine waste characterization using remote sensing methodologies at Asarco's Ray Mine in Arizona. ? Predictive emissions development and testing in

Jan 1, 1997

The process design of a metallurgical plant follows logical steps, one built on another, to define the circuit requirements. The methodology used and documentation produced is the same for a pre-feasibility study, feasibility study or a complete design, regardless of the process complexity or the commodity. The only difference is the amount of detail developed at each stage. SRK Consulting, an independent, international consulting practice that provides focused advice and solutions to clients, mainly from earth and water resource industries, has consulted on many mining projects around the world. The company was formed in 1974 and now employs more than 1,600 professionals in more than 50 offices on six continents. According to SRK experts, the first element in plant design is collecting metallurgical testwork or operating data from an existing plant. The testwork identifies the process, the metallurgical recoveries and product qualities and establishes the process parameters for economic recovery of the commodity. Test samples must represent both the whole orebody and the feed over the life of the mine, showing the mineral?s variability. With this data available, the process design can be developed.

May 1, 2013

By H. M. Woodrooffe

In the U.S.S.R. three of the world's major-known phosphate deposits are located. These have an estimated reserve of 2,600 million short tons of contained phosphorus. The best known lies in the "Khibiny Massif', an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. Location and Climate The Khibiny Massif lies north of the Arctic Circle in the Kola Penin-sula, 100 miles south southeast of Murmansk, at a latitude of 67° 30' north and a longitude of 35° 30' east. It is serviced by rail from Murmansk and Leningrad (900 rail miles south). Figure 1. The phosphate operations are centered about the two cities of Apatity and Kirovsk. The former has a population of 35,000 and is on the Leningrad¬Murmansk railway. Kirovsk, 15 miles to the east, is now a city of 85,000. The region is at the limit of the tree line with most of the ground cover typical tundra. The mean annual temperature is -4°C and, in a normal year, precipitation occurs on 240 days. Because the temperature does not exceed freezing for 300 days each year, virtually all of the precipitation is snow. The two towns are nestled between mountains and, because of the weather, extensive avalanche control systems incorporating major engineering construction have been introduced to divert snow slides away from the populated areas. General Kirovsk was first settled in 1923 and the apatite occurrences were recognized shortly after. In 1933, the first concentrator for the recovery of the mineral was completed, producing in its first year of operation 170,000 tons of concentrate. With the growth and demand for phosphate in the U.S.S.R., a second concentrator was erected at Apatity. It calve on stream in 1963. Because of the severe climate, in the early days mining was limited to 85 days per year. With the introduction of new techniques and improved mining methods, the season has been extended to 115 days.

Jan 1, 1972

By W. G. Willson

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture re-absorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid fuel.

Jan 1, 1997

By John Relser

The production processes that are developed in the mining and minerals industry are manufactured to be exposed to very aggressive environments. Chemical, abrasion, and impact expose structures and equipment, steel or concrete, to a significant deterioration. This causes damage and adds high costs to operations that can be reflected in the destruction of equipment and structures in the arrest of the production process, which becomes very costly. Also, there is the potential for personnel accidents, which would require large sums of compensation for an employee, thus directly harming the image of the mining operation and company. Manufacturers of paints and coatings that have major centers for research and development (R&D Labs) distributed globally have developed high-tech products for durable protection from the elements for structures and equipment used in the mining industry. The difference between these paintings and coatings and what is normally known as conventional paints (e.g., those called domestic or decorative), is its chemical composition, structured around polymeric components that have highly resistant, chemical and physical properties to cope with extreme conditions to which they are exposed. With this, and only this, longer life of components can be achieved for equipment and structures used in the production processes of the mining industry. Today, in addition to the important features mentioned, some manufacturers of the paints and coatings dedicated to this highly modernized process have invested large sums of money in developing new products that add operational elements to the painting process. These coatings provide added value and significant performance to companies mining operations and that we can describe in three fundamental concepts:

Feb 1, 2014

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By Kwangmin Kim, Taehee Lee, Minkyu Kim, JUNHYEOK PARK

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. About 25 percent of the mass fraction of tailings from a hard-rock mine consists of particles of a respirable size (smaller than 10 μm) [1]. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. Respirable tailings dust, primarily composed of quartz or free silica (SiO2), may cause silicosis, chronic pulmonary disease, bronchitis, collagen vascular diseases, and chronic granulomatous infections [2]. 

"The 33rd annual American Mining Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 5, 2015. Each year, one living Hall of Fame inductee, two Medal of Merit recipients, several honorees from Mining’s Past, an Industry Partnership Award and a Special Citation are recognized for their respective contributions to the mining industry.Conrad E. Huss, cofounder of M3 Engineering & Technology Corp. located in Tucson, AZ, will be honored as the 2015 Hall of Fame Inductee and will serve as the keynote speaker at the awards banquet. Huss has served his company as chairman of the board for its entire 30 years and guided M3 to become a full discipline firm. Now M3 offers complete project execution through engineering, procurement and construction management procedure and has become a major engineer of large observatories around the world. The company now has more than 1,000 employees with offices in Arizona, North Carolina, Mexico, Argentina and is incorporated in Guatemala, Peru and Canada.The Medal of Merit will be awarded to Charles Michael (Mick) Lownds, founder of his eponymous consulting firm in Salt Lake City, UT, for his 42 years in commercial explosives following tenure at Sasol and at Orica. Originally from South Africa, Lownds immigrated to the United States in 1998 and has made significant advancement on electronic initiation systems. Lownds has published numerous technical papers, is an inventor with 12 awarded United States patents and was also the recipient of the President’s Award from the International Society of Explosives Engineers in 2000.Medal of Merit for young professionals will be awarded to Fiorella Giana, Freeport- McMoRan Inc.’s (FCX) mine manager at Bagdad. Born in Buenos Aires, Argentina, Giana left the small cattle farm where she was raised in 2001 to pursue higher education in the United States. For the past decade at FCX, as a result of her extraordinary combination of technical skill, leadership and commitment to excellence, she has been given positions of progressively greater responsibility from an entry level engineer to senior mine engineer, to chief engineer and now as mine manager, a position rarely held by woman."

Jan 1, 2015