Search Documents

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By E. Steiakakis

This paper presents in detail the procedures followed and the results obtained in order to determine the stiffness parameters of the calcareous marls found in the lignite mines in Ptolemais, Northern Greece. Triaxial tests were performed on representative samples of the inner burden marl and the marl which underlies the lignite bearing series of the region. The tests were conducted under drained conditions, with controlled loading (including an unloading-reloading loop), while the axial strain was measured externally as well as with displacement transducers mounted directly on the specimen (Hall Effect sensors). The geotechnical parameters obtained (i.e., cohesion, angle of friction, stiffness modulus, stress-strain relationship), were subsequently used for simulating the triaxial testing with the Plaxis finite element software. Simulation results are in good agreement with the experimental results. The resulting material model can then be applied to modeling the mobility that is expressed during the excavation of the open pit mines.

Jan 1, 2005

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives – HydroStar® 4208, DXG-F7® and Cyquest® N-900 – using a potentiostatic technique. The current–time data obtained at 0.16V versus the SHE were analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A/m2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current–time data from the electrolyte without organic additives, and confirmed by SEM images, indicate progressive nucleation with two-dimensional growth under diffusion control. None of the organic additives studied at a concentration of 2.5 mg/L with 20 mg/L chloride changed the nucleation and growth mechanism, but the additives increased the number and reduced the size of copper nuclei, leading to more uniform coverage of the stainless steel substrate.IntroductionElectrowinning of copper is an important process in the manufacture of high-purity copper metal. Approximately 20 percent of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth and nature of the initial deposit (Sun and O’Keefe, 1992).Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature and copper concentration, small amounts of organic smoothing agents – traditionally, guar products – are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper nodules and lead to improved deposit quality by producing bright, smooth and dense cathodes.Recently, the use of polysaccharides, such as HydroStar 4208 and DXG-F7, and polyacrylamides, such as Cyquest N-900, has been reported in commercial electrowinning tankhouses as replacements for guar (Ashford, Clayton and Sandoval, 2012; Robinson et al., 2013; Sandoval, Morales and Bernu, 2010). However, little information has been published on the effect of these new organic additives, especially regarding the nucleation and growth mechanisms of copper electrodeposits in their presence."

Jan 1, 2016

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By V. N. Kolesnikov

The Sikhote-Alin part of the Circum-Pacific Ore Belt is characterized by wide distribution of Sn, Pb, Zn, W; Au, Ag, and other mineralization. This mineralization is regionally associated with the Late Cretaceous-Tertiary East Sikhote-Alin volcanic belt where it overlaps the Taukha accretiollary-wedge terrane of the Early Cretaceous age. The Pb-Zn deposits of the Dalnegorsk ore district may be grouped into the skarn (about 80%) and vein types. The skarn deposits are of major commercial value. Their geological position is controlled by the carbonate units located within tectonic melange of the Taukha terrane. Some other lithological and tectonic factors also play a significant role ill distribution of the mineralization. The ore bodies are traced to the depth of 1000-1500 m below the surface, having a pipe-lens shape and vertical zonation. Major minerals of the ores are galena, sphalerite, pyrrhotine, chalkopyrite, hedenbergite, quartz, and calcite. The minor elements of the Pb-Zn mineralization are cadmium, silver, bismuth, and copper. The paper describes relationships between mineral suites and minor element contents in the ores, as well as their significance for processing the ores. The metallurgy applied allows high recovering of the major components (Pb -93.9%; Zn -91.4%). However the tails contain some minor components that may be of commercial interest.

Jan 1, 1998

By L. G. Austin

Using an instrumented laboratory high-pressure grinding rolls mill, the grinding force, gap dimension, mass flow rate and net mill power were measured for six coals and a crystalline quartz. A technique was developed to estimate the compressive stress-strain curves for compression of the materials in the mill plus the effects of elastic decompression. To reconcile the mill power and grinding pressure results, it was necessary to allow for the energy recovery on decompression. No clear correlation was obtained between the form of the stress-strain curves or the variation of specific mill power factor with the Hardgrove grindability index (HGI), although coals with the lowest and highest HGIs (i.e., 44 and 106) gave results significantly different from the other coals. Feeds below 140 mesh (105 µm) flowed more rapidly than coarser feeds and would not build up high grinding pressures. This indicated shearing and fluidlike properties rather than compression as a locked bed.

Jan 1, 1998

By Willard C. Lacy

Discovery of a mine is a complex affair. No mine is simply found but comes about through the efforts of many. It is difficult to establish "credit" when a mine is found and becomes a viable operation, or "guilt" when a mine is lost, goes bankrupt, or remains undeveloped. The story of the Toquepala and Cuajone developments entails various stages of: (1) discovery and recognition; (2) testing and innovation; (3) political and industrial negotiation and intrigue; and (4) finance, development, and operation. The Toquepala and Cuajone projects introduced innovative drilling techniques, were among the first major porphyry copper deposits to utilize induced polarization (1P)geophysical methods, were among the first deposits to undertake complete feasibility studies on drilled- out ore bodies, and were developed by the first large Western Hemisphere copper mining consortium. Many persons have contributed to the development of these two great deposits. Some of the names have been lost and certain contributions have gone unrecognized. I apologize for these omissions.

Jan 1, 1991

By E. Kaya

Investigations of fine grinding of bituminous coal in a laboratory-scale pulverizer are described. The results indicate essentially "normal" breakage behavior at relatively coarse sizes (greater than about 20 µm) but show clear evidence for re-agglomeration in the fine size range (less than about 10 µm). A simplified population balance model for simultaneous growth and breakage has been formulated. Breakage rates and breakage distributions are assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behavior. Agglomeration rates are assumed to be determined by contact probability, i.e. by the relative numbers of interacting particles. Based on comparisons of model simulations and experimental data, it appears that agglomerate re-breakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1996

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By Charles L. Karr

Researchers at the University of Alabama in cooperation with the U.S. Bureau of Mines have developed adaptive process control systems in which genetic algorithms (GAS) are used to augment fuzzy logic controllers (FLCs). GAS are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by mimicking the search procedures of natural genetics. FLCs are rule based systems that efficiently manipulate a problem environment by modeling the "rule-of-thumb" strategy used in human decision making. GAS and FLCs can be combined to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and a learning element to adjust to the changes in the problem environment. I" this paper, the details of an ongoing research effort to develop and implement an adaptive process control system for a column flotation unit are discussed.

Jan 1, 1996

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By G. E. Slagel

On August 3, 1987, a hearing was held by the House Subcommittee on Energy and the Environment to commemorate the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). Four panels of environmental/citizen group representatives went before the Subcommittee to report on the state of affairs (from their perspective) of the coal industry and the Office of Surface Mining, Reclamation and Enforcement (OSMRE) As expected, these groups had little positive news to report and continued to focus on glaring deficiencies within the surface mining program. They indicated that gross abuse of SMCRA has continued over the past ten years and the states have performed poorly. Congressman Udall's opening comments perhaps best characterized the mood of the group with his statement that "The Act has not accomplished what I or the people of the coalfields had hoped." and " ? a segment of the coal industry has continued in its bitter and implacable opposition to the most basic of environmental controls."

Jan 1, 1988

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000

By P. R. Khangaonkar, G. Bhaskar Raju

Three types of flotation columns were developed with a column dia of 8.0 cm and a length of 160 cm. The first type consists of an ordinary column fitted with a porous plate at the bottom. The second type consists of two electrodes at the bottom to obtain very fine and uniform bubbles generated electrolytically and the third is a combination of first and second types, i.e. to get both electrolytic bubbles and air from the compressor through porous plate. Three different ores were tested-gold tailings for recovery of scheelite, copper tailings (chalcopyrite) and oxide copper ore. In the case of scheelite and copper oxides, good results were obtained with the first type of column itself, whereas the third type column was found fairly effective in the recovery of chalcopyrite. The variables like the effect of reagent concentration, column height above the feed point, feed flow rate, current density, air flow rate, particle size etc. were examined.

Jan 1, 1988

By L. M. Klimov

In recent gears in the coal industry a great deal of attention is attached to the questions of elaborating and introducing the problems of planning and management and, first of all, in the sphere of mine production. The basis for planning of mi- ne production is complexes (sets) of problems for planning the development of mining operations based on different time periods, ensuring the follow-up of changes of mine productive capacities. Complexes of problems for planning, the development of mining operations at existing underground and surface mines within the OASUugol system (Coal Industry-wide Automatic System of Management) are aimed at ma- king decisions close to optimum, i.e. general lay-out of panels, blocks and pillars; transport and ventilation networks; schedules for working out parts of mine take; coordinated mining operations with limited labour and material resources; control of mining operations and ultimately maintaining productive capacities of existing mines at the required level.

Jan 1, 1979

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc '" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988