Search Documents

By Peter L. Dunn

With the advent of new high-strength magnetic materials, rare-earth magnetic separators have become more common place for processing heavy mineral sands. In many instances, rare-earth magnets have replaced conventional separators such as electromagnetic cross-belt and induced-roll type machines. This paper will present the results from a detailed test program developed to evaluate the performance of rare-earth drum and roll separators for processing heavy mineral sands. The effect of machine design parameters, such as magnetic element configuration and separator diameter, will be reviewed in light of these test results. The impact of basic operating parameters (i.e. feed rate and roll speed) on separation efficiency will also be presented.

Jan 1, 1999

By J.N. Kohmuench

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters, including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By Dirk van Zyl

Three conditions are required for a risk to be realized: (1) a source of risk (i.e., hazard) must exists (2) some process must take place which will lead to the exposure of people, animals, and/or the environment to the hazard: and (3) as a result of the expense, undesirable effects are produced on the people, animals, and/or the environment. A comprehensive risk assessment addresses all three of the conditions through the following four steps: (1) risk source (hazard) characterization, (2) exposure assessment, (3) dose-response assessment, and (4) risk estimation. Although the terminology may differ, the overall approach of financial, public health, and environmental risk assessments is the same (National Science Foundation, 1985).

Jan 1, 1988

By A. Ballester, F. Gonzalez, M. L. Blázquez

Pyrometallurgical process are usually used to recover valuable metals from metal sulphide concentrates. However, their use is diminishing as the cost of energy rises and pollution controls become strictes. An alternative method of treatment sulphides could be bacterial leaching due its simplicity and negligible contamination (1-2). This process is presently used commercially to re cover metals such as Cu and U from low grade ore concentrates. In spite of numerous researchs during recent years (3-5) there exists very little kinetic data concerning the speed of bioleaching process. The kinetic analysis of bacterial activity is related with the metabolism and growth of microox ganisms . This fundamental information permits ma- king the best utilization of bacterial oxidation and to suggest techniques which might increase the production of the products desired. However, bio- kinetic models are especially complicated due to the existence of many metabolic routes and parallel reactions which are important for the life of the bacteria. Microbiological oxidation of a mineral substrate is influenced by its own inicial concentration: This influence can be determined by means of a kinetic study. In a medium with sufficient concentration of nutrients (nitrogen, phosphorous and potassium) and an adequate supply of 0, and CO2, as the only & L source of carbon for the biochemical synthesis, the substrate concentration would remain the only limitation in the rate of leaching. In this case the Michaelis-Menten model could be applied (6). The model is based on an association of the enzyme (El with the substrate (S) with consequent decomposition of the latter into enzyme and products [ ] The rate of dissolution is defined by the equation : [ ] Were V is the rate of metal extraction (mg 1-1 1 h-1 ) ; S is the pulp density Mn is the maximum rate for metal extraction (mg 1-1 h-1) and K is the constant of Michaelis (concentration of substrate that yields Vm/2). This method is applicable only when the rate of bacterial growth is similar to the rate of metal extraction. It would therefore be sufficient to control the concentration of metal in the medium over the period of time. In the present work a systematic study of the kinetics of ZnS and CuFeS bioleaching in sphalerite and complex ore concengrates was carried out. The rate of dissolution of the Zn and Cu as function of the pulp density and temperature was determined. However, most oxidations of sulphide dissolution take place with a very slow kinetic; but, this can be accelerated considerably by the addition to the solution of suitable catalytic ions, as was Suggested many years ago by Bjorling (7). Such ions can exercise an important influence on the rate of the oxidation-reduction reactions, both homogenous and heterogenous, which take place during the leaching of sulphides; they also affect the nature of the reaction products. The action of catalytic ions has been fully developed in aqueous systems, but in the absence of bacteria (8 - 11) although the actual machanisms is not totally known. The mechanisms proposed as hypotheses in the literature (8) indicate that, in the case of ZnS, the catalyst ion act through an electrochemical mechanism according to the reactions: [ ]

Jan 1, 1989

By Mary-Lee Athorn, David A. Barratt

An opportunity to compare the performance of different tunnel boring machines (TBMs) operating in similar rock conditions occurred during the construction of a major water scheme in the UK. The principal objectives of this study were: (i) To collate, analyse and present the data available for the four TBM drives of the Kielder Aquaduct Scheme in terms of the tunnelling system performance and the downtime experienced, particularly where these were influenced or controlled by geotechnical parameters. (ii) To isolate the major sources of machine downtime and highlight those aspects of the tunnelling system that critically affect tunnelling progress rates (iii) To determine, by statistical techniques, relations between TBM performance and rock properties.

Jan 1, 1986

By W. D. Monaghan

One of the major ignition sources of fires and explosions in underground U.S. coal mines is flame cutting and welding. On May 20, 2006, a flame-cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On Jan. 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame-cutting and welding operation at the Loveridge Mine caused a fire that required sealing the mine for an extended period. On March 19, 1992, an explosion initiated by welding at the Blacksville No. 1 Mine resulted in four fatalities. These examples of mine incidents demonstrate the need to conduct research to develop best practices for safely conducting flame cutting and welding in underground coal mines. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame-cutting and welding operations to determine the root causes of these types of incidents. The methodology included interviewing mining personnel who perform flame-cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations. In addition, MSHA reports of investigations and accidents statistics were analyzed. The findings were used to identify and compare differences between flame-cutting and welding practices and techniques in small and large mines, eastern and western mines, low-seam and high-seam mines, room-and-pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices were developed to reduce the number of ?res and explosions caused by flame cutting and welding. This paper provides a summary of this research.

Jun 1, 2010

By R. Kalra

The current paper looks at evaluating the merits of large geared mills versus gearless driven mills by evaluating the following factors: The capability of currently available systems in terms of power and mill diameter Efficiency in terms of overall electrical power consumed vs mechanical output power Capital cost Running costs Cooling requirements in terms of air versus water cooling Installation and delivery time World?s largest geared drive ? 2x8500kW ? Wushan, China (operating) Among the many reasons that geared drives on large SAG mills are not favoured, is due to not having an efficient variable speed drive option (60 to 80% critical speed), which is required for process reasons. As technological advances have occurred quite rapidly in recent years, this paper uses the latest data in applying these comparisons and attempts to dispel some of the myths regarding Slip Energy Recovery (SER) and variable frequency drive technology on twin pinion drive systems. Early attempts to provide load sharing on twin pinion drives used primitive electronics which have since been developed to eliminate the problems encountered in earlier attempts. In particular, torque pulsations between the twin motors have been overcome using a higher number of devices (pulses) and better electronics. With successful operation of 2 x 6.5MW (Phu Kham, Laos) and three 2 x 7MW units under manufacture (Pascu Lama) and a further 40 projects worldwide, energy efficient Hyper Synchronous SER drives are now mature and ready for use on 2 X 10MW dual drive mills. Speed variation required is in the range of +/- 15% of synchronous motor speeds. VVVF drive packages from ABB and Siemens are also available for 2 x 10MW in low and high speed options. Dual hydraulic inching drives provide a much safer and convenient operation with the added advantage of locked charge detection.

Feb 27, 2013

By Paul Madsen, Bade Sozer, Thomas Hennings, Eileen Test

The Rondout Bypass Tunnel in New York has two access shafts. The upper sections of the shafts are lined with steel pipe to resist a substantial net internal water head . Initial design included a ¾-inch-thick cement mortar lining (CML) for all three components. Because of concerns with CML application on large-diameter pipes, the protective lining was redesigned for shotcrete application. This paper discusses the details of that design, mock-ups, and shotcrete application.

Jun 13, 2023

"Metallurgical process development in greenfield projects must define the comminution flowsheet and establish the equipment sizes that are required to deliver the project design criteria. These are critical steps that heavily influence the financial performance of the project, requiring a detailed understanding of the ore properties of the project resources and the best practice methods to size comminution machines. This paper reviews current practices for determining the ore characteristics relevant to comminution circuit design. Particular attention is given to the design of sampling and testing programs, and the methods commonly applied to size crushers and mills for conventional size reduction applications in mineral processing. IntroductionMetallurgical process development in greenfield projects requires the selection of a comminution flow sheet and must establish the equipment sizes required to deliver the project design criteria. This necessitates a detailed understanding of the ore properties that define the project resource. For brownfield projects the same objectives may apply for plant expansions, or the project objective may be simply to define the capacity and operating cost of an existing facility for a new ore source. The process development phase in either instance will typically comprise the following key activities:• Geometallurgical classification and sampling of the ore deposit or deposits.• Determination of comminution energy requirements.• Benchmarking similar projects.• Identification of flow sheet options.• Equipment selection and sizing.This paper is concerned specifically with process development testing and will as such focus on the first two activities on the list: sampling and testing of the deposit. The discussion will focus on testwork programs to support the design of comminution circuits commonly in use in mineral processing today, specifically crusher, tumbling mill and stirred mill technologies.It is important that any testwork program is designed giving consideration to the types of flow sheets that are viable for the project, and the data that will need to be generated to support the final equipment sizing. Designing a testwork program to only provide information about one particular type of flow sheet will not allow sufficient information to be generated for a rigorous trade-off analysis of options, and may therefore preclude financial optimization of the project. Testing programs should be designed to collect sufficient data to ensure that any backtracking at a later stage to fill in missing information is minimal."

Jan 1, 2016

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By Andrew Hall

Many Latin American countries are facing a scarcity of water. As such, infrastructure decisions are quite different from those made in parts of the world that experience a positive water balance. In the latter case, the water treatment approach tends to be ?treat and discharge.? For Latin American regions facing the challenges that go with a negative water balance, the focus is on resource optimization and reuse. Historically, the water challenge has had a significant impact on economic development in Latin America, especially in sectors such as mining, where water usage is high. At the same time, countries such as Chile and Brazil are major development targets for mining and oil and gas operations. Given the water supply challenge, industry is increasingly turning to technologies and processes that maximize water recovery and reuse. With sulfide precipitation and ion exchange water treatment processes for example, it is possible to treat and recover more than 99 percent of water for reuse onsite. These technologies have been applied successfully in other regions of the world where water conservation practices are essential to economic survival.

Jan 1, 2012

By M. J. dos Santos

"INTRODUCTION In his landmark Society for Mining, Metallurgy and Exploration (SME) 2000 writing, “Theory and Design of Sandwich Belt High Angle Conveyors According to The Expanded Conveyor Technology” J.A. Dos Santos generalized the belt conveyor technology to include all possible variations and augmentations including, particularly, multiple belts along a common carrying and/or return path as is the case most notably in the sandwich belt high angle conveyor technology and belt-on-belt type intermediate (booster) drives. Figure 1, excerpted from his writing, represented the proposition of the generalized “Expanded Conveyor Technology,” abbreviated ExConTec.This formed the basis for the generalization which was completed in theory and in math before 2000 and presented by J. A. Dos Santos at the Y2K SME Annual Meeting. The writing can be found in the SME library (Dos Santos J. A., January 2000). While Figure 1 with the supporting mathematical development solved the generalization, it failed to identify the variation that would prove to have the greatest significance. As with most significant developments, necessity is the mother of invention. This is the case with the Adder Snake belt technology, the subject of this writing. BACKGROUND The concept of elevating bulk materials at a high angle using the sandwich belt concept was first introduced in 1951. That introduction did not produce any lasting success. Commercial success was achieved in the 1970s with the Loop Belt, a sandwich belt elevator of C-shaped profile developed by Stephens Adamson of Canada. The Loop Belt was and is the vital element of a conveyor based self-unloading ship system. Such self-unloading ships have had great success achieving unloading rates above 10,000 t/h with Loop Belts of width to 3,048mm (120”). Being strictly of C-profile, Loop Belts could not be adapted to the general high angle conveying path which is predominantly along a straight incline. It was the success of the Loop Belts that inspired the Dos Santos Sandwich Belts of the 1980s. These expanded the Loop Belt capabilities by producing endless elevating profiles that could take the most direct and/or conforming path between the loading and discharge points. Sandwich Belt high angle conveyor systems have seen great success through the years, with more than 200 installations throughout the world."

Jan 1, 2018

By C. Geier

Previous mine incidents show weaknesses in mine rescue preparedness from poor training in decision making, leadership and incident command center (ICC) protocols. Computer simulations offer a larger range of training opportunities for mine rescue teams focusing on exploration and communications. The mine rescue simulator developed by the Colorado School of Mines and Rite Solutions Inc. utilizes four computers for the instructor and team, with the instructor monitoring the team?s progress. As the team explores, it relays information back to the Fresh Air Base, which then reports to the ICC. This forces a three-step communication procedure, enhancing the team?s overall communication skills and developing ICC protocols. The simulator is decision-based, demanding team decisions be made quickly. Upon completion, teams commented positively. Generally, participants said that the simulator is useful for learning how to communicate and make decisions during mine rescue emergencies. This mine rescue simulator improves team training, providing effective communications practice with an easy setup and no production interruption.

Feb 1, 2014

"It’s been 80 years since Charles Warman invented the iconic Warman slurry pump, a pump that revolutionized the mining industry and continues to push the boundaries of pump performance to this day.In honor of this legendary brand, Weir Minerals hosted an event at the end of May in Kalgoorlie, Western Australia. Throughout the evening, attendees relived Warman pumps’ history and gained an insight into some of the future innovations planned.“It was a privilege to share this special night with some of our key customers, past and present employees, and members of the Western Australian School of Mines,” said Ricardo Garib, divisional president of Weir Minerals. “Warman is one of our leading brands. It has truly shaped the mining industry over the past 80 years and is a product we are all very proud of. The Warman pump, invented to solve high wear issues in slurry pumping, created a thriving industrial business that is now the cornerstone of Weir Minerals with more than 8,000 people, and more than 150 manufacturing and service centers across the globe.”Always inventingCharles Warman invented the Warman slurry pump in Kalgoorlie in 1938. It was a hardwearing slurry pump that used replaceable liners and a replaceable impeller, something that had never been done before.“Charles Warman was a visionary and an innovator. The use of rubber lining in the pump was groundbreaking as it reduced total ownership costs, was safer to handle and offered extended wear life in many abrasive slurry applications. It is a great example of solving customer problems with material science, and is still taught in universities today,” said Marcus Lane, global product manager for centrifugal pumps at Weir Minerals.It was quickly adopted throughout the goldfields in Western Australia and by the 1950s, as customer demand rose, Warman expanded his business by opening offices in Sydney and Perth.During the 1960s the rapid growth of the business continued with manufacturing and sales outlets established around the world. The Warman Series ‘A’ pump was accepted and became a world leader in its field. Further work on the Warman AH pump resulted in the development of interchangeable metal and rubber wearing components."

Jan 9, 2018

By Taghi Sherizadeh, KUTAY E. KARADENIZ, Dogukan Guner, Samuel Nowak

Underground mining environments bring with them occupational health and safety issues with some severe dangers, such as mine explosions. During such events, miners may escape using main access openings or find a safe haven like a refuge alternative (RA) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is detailed, depending on conditions and abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification of resistance to explosion is discussed in particular, and studies in the literature are examined in terms of structural deformation.

Mar 1, 2023

By S. Klein, M. McLeod, K. Johnson

The East Bay Municipal Utility District (EBMUD) delivers water to the San Francisco Bay Area through an aqueduct system extending from the Sierra Nevada Mountains to the East Bay. This aqueduct system, the Mokelumne Aqueducts, are comprised of three 82-mile long steel pipelines. The portion of the aqueducts crossing the Sacramento-San Joaquin River Delta is recognized to be vulnerable to seismic and flooding hazards. Previous studies evaluated alternatives for mitigating these hazards and increasing the reliability of the aqueducts for the next 100 years. The preferred solution involves construction of a 16.5-mile tunnel across the Delta and re-routing the existing aqueducts through this tunnel

Dec 1, 2022

By Ulrich Maidl, Jamal Rostami, Ulf Gwildis

Tunnel Boring Machines (TBM) have more or less become the preferred method of tunneling in various ground conditions and Programmable Logic Controllers (PLC) or microprocessors are standard features on TBMs to monitor and record various sensory systems on the machine providing the possibility for machine automation and control. The data collected from these sensory systems and channeled through PLC is stored for real-time analysis or use by the operators. Based on typical construction specifications, part of the information collected in the process is shared with the project management team representing the owner. Machine data automatically acquired during TBM advance is typically processed by specialized software to offer the project team data visualization and evaluation options. Interfacing with Geographic Information System (GIS), Computer-Aided Design (CAD), 3-D geologic model, instrumentation data bases, and Document Management Systems (DMS) allows for developing Building Information Models (BIM) of the tunnel’s as-built condition. Application of Artificial Intelligence (AI) processes such as Machine Learning (ML) have already been used for analysis of data, including performance prediction of hard rock TBMs, and exhibited the potential of big data analytics in improving the productivity of the operations. This paper outlines anticipated disruptive technological advances with implications on geotechnical exploration, TBM operation, face condition tracking, subsurface risk allocation, and claims management in the future.

Jun 13, 2021

By C. Roos, K. Jetmore

Developing a strategic underground mine plan is challenging and investigating multiple scenarios may take weeks. This process can be sped up using the Theory of Constraints to isolate the bottleneck mining activity and simplify the mine schedule process. This paper presents a technique to apply the Theory of Constraints to test multiple cutoff grade scenarios in Mineable Shape Optimiser and quickly produce many high-level production-based schedules that can be easily interpreted using stope-by-stope graphs, the Hill of Value, and through incremental return analysis.

Mar 2, 2022

By J. Peterson, R. Michael, D. Yantek, E. Ferro

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. To address this problem, the U.S. National Institute for Occupational Safety and Health Office of Mine Safety and Health Research (NIOSH OMSHR) conducts research to reduce the noise emission of underground coal mining equipment, an example of which is the roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that roof bolting machine operators would be exposed to, and it contributes significantly to the operators’ noise exposure. OMSHR has determined that the drill steel and chuck radiate a significant amount of noise during drilling. OMSHR and the Corry Rubber Corporation (CRC) have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and in turn reduces the noise exposure of roof bolter operators. This paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB.

Jan 1, 2011

By Meghan M. Murphy, Derek Penrice

The Downtown Rail Extension (DTX) is principal element of the planned second phase of the Transbay Joint Powers Authority’s (TJPA) Transbay Program. When complete, this regionally critical project will connect Caltrain’s regional rail system and the California High-Speed Rail Authority’s statewide system to the Salesforce Transit Center in downtown San Francisco via a 1.3-mile tunnel. Studied since the 1970s, the DTX has now received environmental clearance, and key stakeholders are aligned on the project’s configuration and its expedited delivery. This paper describes efforts to optimize the DTX configuration and develop an informed project delivery strategy that incorporates construction industry feedback on project phasing, contract packaging, and procurement methods that accomplish the project’s budget goals.

Jun 13, 2021