Search Documents

By H. Walqui, J. Drelich, J. Pletka, E. Luhta, E. Raber, J. Wieland, P. Boyd, N. Tervo, D. Herron, S. Boston

Mini-projects studying the flotation chemistry of paper de-inking were incorporated to an educational program at Michigan Technological University with support from the paper recycling industry. Interfacial activity of frothing agents, surfactants and polymers in de-inking flotation systems has been studied through flotation, atomic force microscopy, zeta potential, contact angle, surface tension, and froth stability measurements. These fundamental studies were developed to understand microscopic and molecular effects occurring in flotation of ink particles that may lead to improved designs in de-¬inking flotation processes. Fundamental studies indicate that ethoxylated alcohols are efficient frothing agents in flotation and can be used to clean the recovered paper from hydrophobic ink particles. Next, it was further supported in this research that the fatty acids activated by calcium ions act as collectors in flotation of ink particles. Finally, improvements in de-inking flotation are reported in laboratory tests involving aqueous solutions of polymeric flocculants.

Jan 1, 2001

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

The response of 174 domestic water supplies to longwall mining of the Pittsburgh coal seam was compared to various physical parameters. Sixty-four percent of domestic water supplies returned to service without the need for intervention, while thirty six percent required intervention to reestablish a suitable water supply. Domestic well response is strongly correlated with the topographic setting. Valley wells showed the least effect while hilltop wells showed the greatest effect. Well response was also found to be correlated to the location of the well above the mining with greater effects observed in zones of surface tension and compression, and fewer effects in zones which are stress neutral. Ground water supplies remained unaffected or were re¬established at 149 of 150 sites, indicating that ground water resources remain available to domestic wells after mining. Results of this study support the stress-relief model of ground water flow in the Northern Appalachian Basin. Longwall mining's effect on this system is to locally increase fracture connectivity in the near surface zone. This may shift the zones of saturated fractures to greater depths beneath hilltops and hillsides, and increase recharge and storage in valleys. General trends in well response are predict¬able utilizing the stress relief conceptual model, the topographic setting of the water sources, and their location over the mine.

Jan 1, 1986

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998

By Patrick J. Doig

The NS9 Drop Shaft contract formed part of the Waste Pollution Abatement Program (WPAP) conducted by the Milwaukee Metropolitan Sewerage District (MMSD). The contract involved the construction of two shafts, a deaeration chamber and connecting tunnel, and ancillary facilities. Portions of the construction were located in saturated overburden where dewatering was prohibited. Ground freezing was utilized for temporary support of the excavation. This paper concentrates on the freezing system and the excavation of frozen ground, with particular emphasis on the use of mechanical cutting equipment, including a raiseborer and a roadheader.

Jan 1, 1991

By T. E. Bernard

"Refuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet the U.S. Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and management of heat from the occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements and carbon dioxide generation that are representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current U.S. coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in.) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in a refuge alternative. The highest likely metabolic heat generation ranged from 113 to 134 W, depending on occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 L (0.81 cu ft) of oxygen per hour per person and 20 L (0.71 cu ft) of carbon dioxide per hour per person, which means the margin of safety is 50 percent or more compared with the MSHA requirements. The information on metabolic heat generation can be used to assess refuge alternative thermal environments by testing or simulation. The required oxygen supply and carbon dioxide removal can be used to assess refuge alternative requirements. IntroductionRefuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet U.S. Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen (O2), removal of carbon dioxide (CO2) and management of heat resulting from the refuge alternatives’ occupants and mechanical/ chemical systems (MSHA, 2008)."

Jan 8, 2018

By D. Yadon, P. Lee, W. Kelly, C. Stilwell

Rico is a small town in an old zinc mining district in a mountain valley of southeastern Colorado. Mine waste rock and mill “tailings” remained after over 100 years of mining in the area, leaving associated surface water and groundwater impacts. Atlantic Richfield Company is proposing an innovative approach, which uses lime precipitation and wetland ponds (semi-natural system, also called treatment lagoon in a wetland setting) to treat adit water in the Rico area. Besides using a non-conventional treatment approach, a non-conventional (non-Superfund) regulatory/administrative approach is being proposed. This paper will focus on the water treatment issues and solutions, as well as describing the innovative “watershed” regulatory process.

Jan 1, 2004

By P. Randall, J. Ickes, S. Chattopadhyay

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (Eh) conditions were performed. Since iron (Fe) is present in large quantities in mining wastes, the effect of Fe on leaching of Hg was also determined. Results show that the Hg concentration increased as the pH of the suspension increased until a pH value of 10.65. Thereafter, the Hg concentration decreased sharply. The Hg concentration, in presence of Fe decreased significantly (1/10thto 1/100th). Kinetics results show a relatively slow rate of leaching in presence of ferric ions. The results obtained from the present study are being used to predict the fate and stability of Hg present in the environment, and will therefore, be useful in dictating the nature and suitability of any remediation treatment.

Jan 1, 2003

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By E. Lovera

Social attention to environmental aspects, steadily increasing in European Countries, has been leading to a stricter regulation of many productive activities. Among them, mining and quarrying sectors have been often censured for their potential and real impacts on land and environment. Referring to dimension stone exploitation (also the terms ornamental stone or natural stone are here used as synonymous), quarries are often concentrated in extractive basins, where the resource is localized with suitable quality and quantity: this fact has sometimes raised critical environmental situations. Nevertheless, dimension stone quarrying represents in Europe a traditional and important economical activity, source of wealth and employment. Moreover, many natural stones take on a ?cultural? value and may be considered as ?classic?, as they have been exploited since antiquity and are element of the architectural heritage of many Countries. The sector relevance demands the research of a sustainable balance between social-economical needs and environmental protection. Actually, very restrictive environmental protection policies have led to severe limitations to quarrying activity, but the results do not seem to be completely positive in terms of sustainability: on the one hand, closing-down stone quarrying activities imposes a shrinkage in local, social and economical development; on the other, quarrying activity is pushed towards developing Countries, environmentally un-protected, simply moving and putting off to next future the problem. The challenge of the sustainable development of quarrying sector ? recently explored in the European Commission?s communication ?Promoting sustainable development in the EU non energy extractive industry? (COM-2000-265) ? should be achieved through a positive link between theoretical statements and practical effects: sustainability indicators may be an effective instrument to assess and monitor the environmental performance of the industry. The paper refers to the development of specific ecological criteria and indicators, which can be useful to measure and predict the eco-efficiency of a dimension stone quarry, finally pointing out where improvement efforts have to be focused.

Jan 1, 2003

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By D. Bahrami, G. Danko

Spatial and temporal temperature and humidity variations for 5000 years are simulated in an emplacement airway within the conceptual, high-level nuclear waste repository proposed to be built at Yucca Mountain, Nevada. A multi-scale model is configured using MULTIFLUX, a thermohydrologic-ventilation code. The predicted surface temperature of most waste packages during post-closure exceed 140oC, the threshold limit known for likely localized corrosion for Alloy 22 waste package material. Small amounts of infiltration airflow through the mountain in Panel 5 are found to transport liquid water condensate to some of the waste packages emplaced along the peripheral section of the drift due to edge cooling.

Jan 1, 2004

By Robert P. Bell, John T. Waggoner

The Metropolitan Water District of Southern California is designing new outlet facilities for Lake Mathews, including a junction shaft, connecting tunnels, and an ear-shore outlet tower. Since Lake Mathews must remain operational during construction, groundwater inflow potential is a concern. This paper describes the challenges and methods used to investigate rock mass and groundwater conditions at an operational reservoir, where offshore and onshore geotechnical exploration was performed. Several investigative and analytical methods were used to characterize rock mass and groundwater conditions, including rock coring, downhole geophysical and video surveys, hydraulic conductivity testing, automated groundwater level monitoring, and laboratory testing.

Jan 1, 1999

By V. Iordachita

In the beginning of the third millennium, the world mining industry has to cope with many challenges; the continuous need for mineral resource deposits and the mostly unsolved economic efforts should be accompanied with ecologic measures mankind has to take in order to avoid self-destruction. The present paper analyses the possibilities of using underground mining spaces in Romania for storing dangerous waste and suggests viable solutions. The characteristics of dangerous wastes and their disposal in suitable underground spaces are analyzed. Also, some methods for deactivating dangerous solid wastes as well as the importance of monitoring underground spaces in order to eliminate environmental impact risks are presented.

Jan 1, 2008

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1997