Search Documents

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By J. W. Parkinson

With most of the coal currently mined in the eastern U.S. already requiring cleaning to meet electric utility coal specifications, the question remains how medium- and high-sulfur coal producers will provide the even better quality coal expected to be demanded if pending acid rain legislation is enacted. One emerging approach is to crush the coal to liberate additional ash and sulfur so that better quality coal can be produced at equal yields. This paper discusses how to measure liberation. the premiums the utility market is willing to pay for lower sulfur coal, and a staged middlings crushing scheme that promises the benefits of total raw coal crushing but at lower costs. For some coals, cautious application of liberation concepts may be the only way to produce a product that can be quality and cost competitive in the future utility coal market.

Jan 1, 1988

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By K. J. Hartman

The term kaolin is derived from "kauling". a Chinese word meaning high ridge, which was the name of a hill in China where kaolin was first mined several hundred years ago.(1) Other common names used today for kaolin include "clay" and "China Clay". The former word technically has a broader meaning and could refer to various types of clays such as bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin as described above but could also be due to a significant historical use in ceramic applications. The terms "kaolin" and "clay" will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's widespread industrial usages center on the mineral's (kaolinite) physical features of good color, low viscosity and inertness. Kaolin is described as a hydrous aluminum silicate with approximate composition Of 2H20.A1203.2Si02. As will be shown later, a new version of the product, calcined clay with modified hydration content, is gaining widespread usages. Components of any particular kaolin in addition to alumina and silica are viewed as impurities. The more valued deposits and, hence, higher priced kaolin products are those of highest purity.

Jan 1, 1986

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By Qiong Wu, Qinghua Gu, Yichuan Lv, Jin Yuan, Caiwu Lu

"The cut-off grade is one of the important parameters of mining production. Different material cut-off grade is directed to different destinations. Based on reasonable and optimal cut-off grade, long term mining plan and investment decision analysis can be made for mining managers. In view of multiple-metals open-pit, the paper has proposed that multiple-metals cut-off grade optimization model is set using the objective function to maximize net present value (NPV). The method of equivalent coefficient calculation is proposed to convert multi-metals cut-off grade optimization to a single metal cut-off grade optimization. Then the optimization model is applied in a molybdenum and tungsten large open-pit mine in china. The parameters of concentrate price are calculated by PRT in the model and the curve of grade-recovery rate is analyzed and studied according to actual production data. Based on 3D metal deposit model, the distribution of grade-tonnage is analyzed. At final step, an optimal cut-off grade is proposed to guarantee to maximize NPV. The example shows that the model of multiple-metals cut-off grade optimization can provide reasonable analysis for optimal multi-metals cut-off grade and develop optimal production strategies. Introduction Cut-off grade is one of the most important parameters in metal ore mining because of its influence on the overall economic profit of mining production. Along with the development of the mining production, dynamic optimization of cut-off grade is necessary through the analysis of technical economy. It is better to manage the mining production according to the variation of market. The cut-off grade plays an important role in mining production."

Jan 1, 2017

By Ned M. Smith

The Mississippian Salem Limestone, from which dimension stone is quarried in Indiana, is principally a calcarenitic rock formed of fossil bryozoans, echinoderms, and specimens of Endothyra. Numerical associations of the fossils, binding materials, oölitically coated fossils, and voids were determined by counting points on the surfaces of 278 thin sections of the limestone. Median sizes, coefficients of sorting, and skewness numbers were computed from measurements made of constituents in these thin sections. Many other samples and numerous exposures of the Salem and contiguous parts of adjacent formations also were studied. The organisms that furnished the skeletal material for formation of the Salem Limestone were chiefly gregarious and communal. Salem rocks are formed of nearly whole skeletons, of dismembered or slightly damaged skeletons, and of skeletons thoroughly ground up, because currents in the Salem sea varied in their ability to move and damage these materials. Locally the sediments are of uniform grain size because of sorting by currents and because related organisms grew to similar sizes. Rocks of the formation contain different proportions of the fauna both because the animals lived in these proportions and because their skeletons were mixed together by currents. The proportional relationships between members of the fauna were constant locally and for short periods of time. Study and mapping of the faunal associations, numbers of oölitically coated fossils, bedding structures, and size parameters enables geologists to suggest sedimentologic histories and sequences in areas of various sizes. Interpretations based upon such areal studies are necessary for evaluation of the dimension-stone potential within the Salem Limestone.

Jan 1, 1966

By Dennis P. Bryan

The southwestern United States has an abundance of natural lightweight aggregate (NLA) deposits of volcanic origin that are being used in the construction industry within the region. New Mexico, Arizona, Nevada and California utilize NLA in portland cement concrete and concrete masonry units for weight reduction and related economic reasons. The geological environment of the western United States is amenable to the occurrence of natural lightweight rocks because it contains Tertiary and Quaternary volcanic products that include low-density glass and vesicular material. There are two major classical types of natural lightweight materials of igneous origin; pumice and cinder. These account for the vast majority of volcanic rocks that are presently utilized as NLA. Pumice is an ejecta product generally found as part of tuffaceous units associated with nearby siliceous volcanic centers. Cinder, also an ejecta product, is associated with mafic volcanics and is most often found as a cinder cone. Both are highly vesicular. A third type of natural lightweight material, though also associated with siliceous volcanics, is less vesicular than pumice. It is best described as being a slightly pumiceous rhyolite or rhyolite-tuff breccia that occurs as a siliceous dome or tuft unit that is most likely to be glassy. Uses of these natural lightweight rocks center on the construction industry where they are utilized in lightweight portland cement concrete and lightweight concrete masonry units. The major reason for usage in portland cement concrete is cost saving effected by weight reduction in high-rise construction. The major usage in concrete masonry units, or "block", is for weight reduction that enables a mason to lay more lock.

Jan 1, 1987

By C. L. Karr

Establishing suitable control of pH, a requirement in a number of mineral and chemical industries, poses a difficult problem because of inherent nonlinearities and frequently changing process dynamics. Researchers at the U.S. Bureau of Mines have developed a technique for effectively controlling such systems. This technique successfully combines the process control capabilities of fuzzy logic and the search capabilities of genetic algorithms. Fuzzy logic offers an effective mechanism for handling nonlinearities, while genetic algorithms can provide fuzzy logic controllers with real-time adaptive capabilities. This Bureau-developed technique is applied to a laboratory acid-base neutralization experiment. Nonlinearities in the laboratory system are associated with the logarithmic pH scale and the changing process dynamics are due to alterations in pH and buffering capacity input solutions. Results indicate fuzzy logic controllers augmented with genetic algorithms offer a powerful alternative to conventional process control techniques in such nonlinear, rapidly changing systems.

Jan 1, 1992

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By R. Singhal

Canada's coal production is approximately 65.4 million tonnes of which 95 % is produced by surface mining methods mostly from the three Western provinces (British Columbia, Alberta and Saskatchewan). The mines are highly mechanized; productivity gains during the past few years have ranged from 60 -80%. Truck/Shovel methods are common although Saskatchewan lignite is almost exclusively mined by draglines. This paper provides an overview of Canadian Coal mining industry vis a vis surface mining. Emphasis is on application and utilization of mining equipment and associated mining methods.

Jan 1, 1994

By B. J. Vorster

The South African Iron and Steel Company Ltd operates a large Iron Ore Mine in the Cape Province of the Republic of South Africa. The Mine is situated on the farm, Sishen, approximately 600 km west of Johannesburg. The annual capacity of the Mine is 100 million ton of ore and waste and the present production level is 60 million ton. The Mine operates continuously for 6 days a week. The primary equipment used to maintain the above production are 55, 154 t trucks (Wabco and Unit Rig) and 14 P & H shovels. During 1979 an urgent feasibility study into the application of a trolley assist system was launched at the Mine. This was due to the unrealistic escalation in the cost of diesel fuel and the appeal from the South African Government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technical feasible. The estimated discounted cash flow return exceeded 50% and the diesel fuel consumption would be reduced by 120 million litres in the next 10 years. Management subsequently approved the implementation of the system at Sishen. The construction of 7,7 km of line and the conversion of 66, 154 t trucks were completed in March 1982.

Jan 1, 1985

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By Randal J. Barnes, Franck Rellier

Mine ventilation survey data includes generally redundant, usually inconsistent, often incomplete, and always noisy measurements. Yet, these data are essential for operational decisions and represent the foundation of any mine ventilation systems model used for future engineering analysis and design. For example, the basic ventilation network geometry can be measured with a reasonable precision, the network flows can be measured, but with significant errors, and the branch resistance factors can not be directly measured at all. The network-based, constrained weighted least squares approach, presented in this paper, advances a method for the sys tem-wide adjustment of ventilation branch measurements and the consistent estimation of global system parameters (e.g. branch flows, head losses, and resistance factors). The constraints guarantee that the adjusted values satisfy the governing physical laws: conservation of flow, conservation of energy, and the appropriate energy dissipation rule (e. g. Atkinson's RQ2). The weights allow for the proper inclusion of data with widely disparate precision, as well as offering a simple method for retiring old data as the mine changes through time. The post-adjustment sensitivity analysis presents two potentially useful forms of analysis: the identification of previously unspecified leakage branches, and the semi- automatic recommendation for future ventilation measurement campaigns. The overall efficiency of the algorithm is exemplified by the fact that a ventilation network with hundreds of branches and thousands of measurements can be routinely adjusted on a microcomputer.

Jan 1, 1989

Mine design and selection of ore processing capacity depend upon a correct estimate of the grade-tonnage distribution. The estimate must reflect what can be recovered and processed. The McCoy/Cove operation in central Nevada, USA, is a gold and silver mine. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and the log-affine variance correction. From this model, the grade-tonnage distribution was constructed. Optimal pits were generated by utilizing the distribution, and the results were compared with the pit generated by ordinary kriging. Studies indicate that the proposed method for multi-metal recoverable reserve estimation is more accurate than ordinary kriging in terms of both tons and the grade. Using recoverable reserves for mine design will maximize global recovery of mineral resources.

Jan 1, 1997

By III Basham

As environmental laws and regulations become more complex and the economic cost of non-compliance becomes greater, periodic assessment of environmental compliance, identification of potential liability and implementation of any necessary remedial action should be a standard part of the operational methods of any successful business. The title of this paper "Environmental Audits, A Shield, A Sword or A Trojan Horse?" is intended to draw attention to the fact that environmental audits can be used positively to shield a business operations from actual or potential environmental liability; can be used proactively as a 'sword" in both a marketing context ("do business with us because we conduct our business safely and professionally?) and as a mechanism for developing positive relationships with environmental regulators; and, used negatively, as a "Trojan horse", by developing information which those same environmental regulators (or the public) use in an enforcement context against your business or that of your clients. This paper will discuss the concept of environmental audits in general; the pros and cons of conducting the same; and the role of the attorney, as part of the "audit" team, to insure, to the greatest extent possible, that the audit process is productive from both a managerial and legal perspective.

Jan 1, 1992

By P. F. Ziemkiewicz, A. S. Knox

Large-scale use of CCBs in mine environments involves filling surface and underground coal mines with ash to address hydraulic problems, AMD, backfilling and subsidence. The environmental risk of land filling CCBs is generally evaluated by the Toxic Characteristics Leaching Procedure (TCLP) or the Synthetic Precipitation Leaching Procedure (SPLP). However, there is doubt regarding the applicability of these tests to long-term CCBs leaching behavior in groundwater associated with coal mines. The Mine Water Leaching Procedure (MWLP) was developed to provide a site specific risk assessment tool. The MWL Pprocedure is presented in this paper and compared with TCLP as a study.

Jan 1, 2003

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997