Search Documents

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

By Howard W. Earnest

The Rio Blanco Oil Shale Company completed a modified in situ oil shale retorting demonstration at its Tract C-a Lease in the Piceance Creek Basin of northwestern Colorado during the spring of 1982. This demonstration was the first MIS project with shafts rather than adits for access to the mining operation, and it involved several potential hazards which required that particular attention be paid to mine ventilation. Methane was first encountered during shaft sinking and ultimately resulted in the mine being classified gassy by MSHA. Secondly, we encountered hydrogen sulfide in association with the ground water, and this proved to be a more persistent problem than did the methane. Thirdly, in order to burn the underground retorts, it was necessary to provide for potential leakage of retort gases and to obtain a modification to the MSHA standard which forbids fires under- ground. This modification had a significant effect on the ultimate ventilation procedures at Tract C-a. An extensive under- ground air monitoring program was included in the ventilation system.

Jan 1, 1983

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

The removal of tritium from tritiated water (-0.5 µCiIL) was studied by metallothermic reduction using aluminum. The influence of the three variables namely the aluminum powder amount, the NaOH concentration and the reaction time has been studied on the tritium activity reduction. The experimental results and statistical analysis showed that more than 85% of tritium can be removed from the tritiated water. Further work on the tritium recovery as well as efforts to totally decontaminate water by incorporating a cryogenic concept is currently pursued.

Jan 1, 1998

By F. G. Rinker

The world demand for metallized iron continues to increase, keeping pace with steelmaking requirements for lower cost hot metal. Virgin iron ore and in-plant oxide fines can be reduced to direct reduced iron (DRI) and hot briquetted iron (RBI). MR&E has developed an improved coal-based process for cost-effective production of either DRI or HBI. Starting with dry compaction, the process combines the latest technology for material preparation, rotary hearth furnace construction and environmental control. Coarse iron ore fines are blended with pulverized non-metallurgical coal to produce a highly metallized (>90%) product. This paper presents production and installation cost data based on operating and under-construction iron oxide reduction facilities.

Jan 1, 1999

By V. de Macedo Torres

There are technical and commercial limitations on using high fluorine copper concentrates in industrial copper smelters. The presence of more than 1000 ppm of fluorine in copper concentrates affects the sulfuric acid units generally integrated to copper smelters, and penalties are normally applied to high fluorine concentrate prices. Several process alternatives to this issue were studied at CVRD Technology Center (SUTEC): modifications on conventional sulfuric acid plants to use high fluorine concentrates, removal of fluorine containing minerals in flotation using depressants, selective leaching of fluorine minerals and sulfuric leach of copper concentrates. Finally, a hydrometallurgical process of removing fluorine was developed by SUTEC.

Jan 1, 1997

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By K. N. Han, K. Peri, Y. Guan

The leaching behavior of gold in ammonical solutions with iodine as an oxidant was investigated using cyclic voltammogram and Tafel polarization. The majority of the experiments were carried out at 75°C, and the results were compared with consideraton given to the equilibrium of the iodine-ammonia system. The distribution of nine iodide-containing species at various pH values in the absence and presence of ammonia were considered at three different temperatures. It was found that, with the introduction of ammonia into the system, the concentration of iodide (I-), iodine (I2) and triiodide (I3-) is increased substantially, which in turn helps the rate of gold dissolution. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical-controlled mechanism.

Jan 1, 2002

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By Mark Gershon

Most recent work in the field of mine production scheduling has focused on either the computerization of the traditional methods or the development of sophisticated mathematical optimization models. Yet it is clear to all concerned that the optimizers need to be made more practical and the traditional approach needs to be made more optimal. This paper, along with another recent paper (Gershon, 85) open a middle ground between these two approaches. In that recent paper, a heuristic procedure for production scheduling was introduced. Here, a series of short term optimizations are used in a creative manner to approximate the true long term optimization. Since these small optimizations are aimed at blending to meet production quality specifications, this approach is most applicable to commodities where the blending function is very important such as coal, cement, phosphates or iron, to name a few. The traditional and the optimization approaches are so far apart that their' advocates have difficulty identifying with the other approach. This is especially true concerning the difficulty of understanding the optimization models for those not trained in the field of operations research. This paper takes the position that the pro- 120 per role of the operations researcher is to provide not only useful and advantageous approaches, but practical, understandable and implementable ones as well. This is the goal of the paper in describing a new approach, consistent with the traditional methods and aimed at approximating the results of the optimizers.

Jan 1, 1986

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By Donald S. Bubar

The Separation Rapids property, located approximately 60 km (37 miles) north of Kenora, Ontario, Canada, is host to one of the largest rare metal pegmatite deposits in the world. This pegmatite was named the Big Whopper by its discoverer, Dr. Fred Breaks of the Ontario Geological Survey, because of the exceptional length and width of the surface exposure. The property is readily accessible from a main, all-weather road via a network of secondary logging roads. The main line of the Canadian National Railway passes through the village of Redditt, just 40 km (24 miles) south of the property. The Big Whopper is one of the complex-type (petalite sub-type) class of rare metal pegmatites that are geochemically the most highly evolved in the spectrum of granitic pegmatites. Such deposits are economically important as resources for the rare metals lithium, tantalum, cesium, and rubidium. While complex-type pegmatites are found in many areas of the world, most are too small to be profitably mined, however, with an inferred resource in excess of 15 million metric tons (mt) (17 million short tons [st]), the Big Whopper is only the fourth deposit of its type in the world with the size required to be of major economic importance. The other three deposits, which are currently in production, are the Tanco mine in Manitoba, the Bikita mine in Zimbabwe, and the Greenbushes mine in Western Australia. The Big Whopper is situated in the eastern continuation of the Archean Bird River greenstone belt which also hosts the Tanco pegmatite, approximately 60 km (37 miles) to the west. The principal commodities identified in the portions of the Big Whopper pegmatite explored to date are petalite (LiAlSi4010) and rubidium-rich K-feldspar. These are industrial minerals with important applications in the glass and ceramics industries. The Big Whopper also contains substantial quantities of lepidolite, a lithium, rubidium-mica which is the principal ore mineral for rubidium metal. Tantalum and cesium occur in anomalous levels with the petalite mineralization, and the possibility of finding zones of high enrichment in these valuable high-tech metals elsewhere in the deposit is excellent. Such enriched zones are typical of pegmatites as highly evolved as the Big Whopper. To date, the geological mapping and diamond drilling work completed by Avalon have delineated the Big Whopper pegmatite system over a strike length exceeding 1.5 km (0.9 miles), over widths ranging from 10 m to 80 m (30 feet to 260 feet) in thickness, and to a vertical depth of close to 300 m (1,000 feet), where it remains open. The pegmatite system consists of a vertically oriented massive petalite pegmatite dyke striking 280 degrees that is flanked by amphibolites containing a swarm of narrower albite and petalite dykes which have all undergone intense deformation in a high strain zone resulting in folding and intense shearing. The Big Whopper exhibits a mineralogical zonation pattern which is complicated by the superimposed deformation that has both folded and stretched the deposit. Drilling has defined a dilute geological resource totaling 7.1 million mt (7.8 million st) grading 1.283 percent Li20, 0.346 percent Rb20, and .007 percent Ta205 over a strike length of 600 m (2,000 feet), and to a vertical depth of 250 m (820 feet), where it remains open. The petalite and rubidium-rich-K-feldspars contained in the Big Whopper all appear to be of superior quality. The grades are consistent with a petalite content averaging 25-30 percent and a rubidium-rich-K feldspar content averaging 15-20 percent. The remainder of the rock consists mainly of albite, several types of mica, and quartz. Accessory minerals include columbitetantalite, cassiterite, apatite, garnet, and gahnite. Market studies show that the deposit is located close enough to existing transportation infrastructure to access rapidly growing, major markets in the glass and ceramics industries, both in the northeastern U.S. and Europe. There are only three competing lithium minerals producers in the world with the Bikita mine in Zimbabwe being the only major producer of petalite. The other lithium deposits produce spodumene, a less desirable lithium mineral. Lakefield Research Limited has successfully designed a process to produce an ultra-pure petalite concentrate containing up to 4.65 percent lithium oxide, and as little as 0.014 percent iron oxide, low levels of soda and potash, and negligible amounts of other trace elements. With these specifications, Avalon will have an excellent quality product for glass-ceramics applications such as Corningware®, CERAN® stove tops, and other thermal shock-resistant products. Lakefield is presently designing the balance of the flowsheet to produce separate concentrates of rubidium-rich K-feldspar, albite, mica, tantalum, tin, and high-purity quartz. Initial test work indicates that the feldspar products will be of exceptional quality. The K-feldspar concentrates contain 11-12 percent K20 and 1 percent Rb20, while the sodaspar contains over 10 percent Na20, and both have very low iron (0.01 percent Fe203). A preliminary economic model shows that with an initial production rate of 90,000 mt (100,000 st) per year, expanding to 170,000 mt (190,000 st) per year over 5 years, the project is capable of generating over CDN $10 million per year in pre-tax cash flow by year 5 on a capital cost of approximately CDN $30 million.

Jan 1, 2001

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By C. Van Landingham, A. Bailey, R. A. Schoof

A residential metals abatement program has been underway in Butte for more than 20 years. More than 1,350 yard and attic cleanups were completed by the end of 2018; most triggered by lead. While the focus is on remediation of residential soil and house dust, the program also includes a blood lead monitoring program with identification and abatement of additional sources of exposure for children with elevated blood lead levels (BLLs). As specified in the remediation program, studies are being conducted every 5 years to assess BLL data collected from Butte children. The first two studies have evaluated over 6,000 BLLs from 2003 through 2017 and evaluated trends over this time period, by Butte neighborhood, and as compared to areas outside of Butte. These studies showed that rates of elevated BLLs (i.e., those above 5 µg/dL) in Butte children have declined dramatically since 2002 but have been declining much more slowly since 2011. Improved rates of confirmation testing are needed to verify the rates of elevated BLLs. While the RMAP likely has contributed to these declines in BLLs the magnitude of impact cannot be quantified.

Mar 2, 2022

By William Gleason

Since 2004, Dave Kanagy has served as the executive director and chief executive officer of SME. In that role, he has worked with 22 SME Presidents, traveling the world to represent the Society. His prestigious one-million-mile status with United Airlines is a testament to these efforts. He has been to six of seven continents while leading the Society on a journey from a struggling association in 2004 to the largest and arguably the most influential professional mining society in the world. In the following pages, some of those past SME Presidents reflect on their time with Kanagy and paint the picture of a visionary leader who was willing to make the hard decisions for the betterment of the Society while remaining open to new ideas and opportunities. One of his first accomplishments as the executive director was to streamline the SME Boad of Directors from 29 members to nine, making it much more effective. With a keen financial sense, he was able to add value while cutting excess to expand the Society in every measure. As the leader of SME, Kanagy helped facilitate much of the Society’s growth and innovation as the world’s largest mining related organization. He has a B.S. degree in industrial education from the University of Maryland, an M.S. degree in technology education from Eastern Illinois University and is a certified association executive by the American Society of Association Executives. Under his leadership, several unique programs were created or advanced, including OneMine.org, the world’s foremost online mining research library. He enhanced legacy programs and increased collaboration with international organizations. Kanagy is the recipient of prestigious awards, including the Colorado Society of Association Executives’ Professional of the Year award and the Mining and Metallurgical Society of America’s Gold Medal award.

Feb 1, 2026

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests.

Jan 1, 2009

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993