Search Documents

By H. K. Conn

This paper discusses briefly the evaluation of chrysotile asbestos deposits in ultramafic rocks. Such deposits are limited to serpentinized peridotite and/or dunites. The purpose of any evaluation is to determine whether a deposit contains sufficient ore mineral to justify profitable exploitation. Dimensions of a mineral zone are established by conventional methods, such as mapping, ground magnetic surveys, diamond drilling or underground exploration. The value of the contained asbestos fibre Is dependent on numerous physical properties such as fibre length, strength, flexibility, as well as the actual amount of fibre present. The determination of grade is difficult. The Quebec Standard Test (Q.S.T.) is used to grade fibre according to the proportionate lengths of fibre present. A method of visual vein counting allows calculation of an approximate percent fibre together with a simulated Q.S.T. Various drilling methods are discussed, diamond drilling is favored. Bulk sampling is required to determine fibre quality. Correlation of visual techniques and laboratory methods are often difficult. Reasons for any variance are discussed. Underground bulk sampling of most potential ore zones is strongly recommended to confirm the viability of the property. Evaluation of slip fibre deposits requires greater reliance on laboratory testing as visual methods are difficult to apply. Cross fibre has greater inherent strength.

Jan 1, 1971

By E. H. Cho

Pittsburgh #8 coal cleaned by the conventional froth flotation was oxidized in a 2-liter Parr Stirred Top Bench Reactor. The oxidation time was varied up to 5 hours; the temperature, from 150 to 225°C, the oxygen pressure, from 15 to 500 psi; and coal dosage, from 15 to 60 grams in 600 ml of distilled water. The oxidation of coal was evaluated by measuring total acidic group formed on the coal surface as well as by measuring the adsorption of calcium ion from a solution under standard conditions. It was found that the oxidation increased with increasing oxygen pressure without much leveling-off effect. However, the oxidation of coal increased sharply from 150°C to 175°C and then tended to level off above 175°C. The adsorption of calcium was reached more than 3% on the coal oxidized under favorable conditions. The adsorption of calcium on coal increased sharply with increasing equilibrium pH. The BTU loss was sensitive to oxidation temperature. This study concludes that the optimum oxidation of coal should be conducted at high oxygen pressures around (e.g. 500 psi) 170°C for 3 hours. This study also concludes that the oxidation in an autoclave is far superior to that in a fluidized bed in terms of calcium adsorption, BTU loss and reaction time.

Jan 1, 1994

By Ossi V. I. Hintikka

There are several limestone deposits around the Lohja area in southern Finland. Raw material for cement rock is mined from some of them. The formations are geologically complicated, and therefore selective mining is used whenever possible. One of these mines is the Tytyri underground limestone mine, which is divided into two parts; Törmä and Solhem. In addition to the selective mining system hand sorting or picking must be used at the Tytyri mine to improve the overall grade of the blended limestone. Some means were needed in order to improve the quality and to increase the feed rate by the elimination of hand sorting. Sorting machines were considered and eventually a Sortex 811MW was pilot plant tested at the Ojamo mine near Tytyri. This machine now continues to be used on production.

Jan 1, 1971

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of screens were developed for the Coal Cleaning Simulator running under Aspen Plus during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for the size separation and a calculation for moisture content of the oversize product based on particle size and specific gravity distribution. This paper discusses the algorithm for predicting the moisture content of coal dewatered by screens.

Jan 1, 1997

By S. Koro

The current economic climate of low commodity prices and increasing costs has put a lot of pressure on mining companies to ensure their operations will survive through the current economic downturn. While history tells us that the cycle will turn around and prices will go back up again, how many mining companies will be left to take advantage of the next upturn? On average in Australia, the maintenance of mining equipment accounts for up to 50% of operating costs; which equates to nearly $15bn per year. In addition to trying to boost productivity, mining companies are also putting a lot of pressure on reducing costs; all with the intention of maintaining/increasing profit margins and thereby keeping shareholders ?happy?. The whole premise of our economy is based on ?growth? and ?profits?. Movements in the market place force mine owners to ?react? to short term fluctuations. And if that movement is downward; operations people at the sites are forced to start reducing costs. Is this cost reduction done in a logical, systematic way where all risks (short-, medium- and long term) are considered? Invariably, the answer is no! Short term ?fixes? are normally implemented with little, or no, regard for medium- and long-term impact. And the reason for this is that management is not fully focused on the long term; focus is mainly on survival. Decision making is driven by shareholder sentiment and history tells us that this is largely short-term. So given these paramteres to work within, what role can ?Asset Management? play in assisting management to meet shareholder and market requirements whilst still maintaining long-term viability of their operations (to the long-term benefit of shareholders dare I say). As maintenance costs account for nearly half the operating costs of mining companies; the ?smart? management of assets is not only crucial; it is essential for survival in today?s economic climate. What is asset management? Asset Management, according to the UK-based Institute of Asset Management (IAM) is ?the systematic and coordinated activities and practices through which an organization optimally and sustainably manages its assets and asset systems, their associated performance, risks and expenditures over their life cycles for the purpose of achieving its organizational strategic plan.? How important is asset management in today?s mining companies? IAM goes on to say: ?This definition of asset management represents a significantly greater scope than just the maintenance or care of physical assets, and is closer to the central purpose of an organization. Good asset management considers and optimizes the conflicting priorities of asset utilization and asset care, of short-term performance opportunities and long-term sustainability, and between capital investments and subsequent operating costs, risks and performance. ?Life cycle? asset management is also more than simply the consideration of capital costs and operating costs over pre-determined asset ?life? assumptions. Truly optimized, whole life asset management includes risk exposures and performance attributes, and considers the asset?s economic life as the result of an optimization process (depending upon the design, utilization, maintenance, obsolescence and other factors).?

Feb 23, 2014

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996

By Shiou-Chuan Sun

This paper is to be presented at the Annual Meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers, New York, New York, February 18-22, 1962. Permission is hereby given to publish with appropriate acknowledgments, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the Secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the author, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1962

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By R. E. Nivens

In the past, Newmont Gold Company relied on cement for their ore agglomeration process. With assistance from Betz Industrial, Newmont began Investigating the use of polymers for ore agglomeration. If gold recovery would not be jeopardized, then polymers could replace cement and possibly reduce operational costs associated with cement agglomeration. The following outlines the preliminary testing conducted to determine the feasibility of polymer agglomeration with Newmont's ore and the results of the test heap, which was constructed so the program could be examined under actual operating conditions. Similar polymer agglomeration testing has been successfully performed in other Nevada gold operations. By eliminating the need for cement, a polymeric agglomeration program could improve material handling operations, as well as offer the following additional savings. First, the polymer application uses only lime for adjusting basicity, the polymer does not contribute any alkalinity to the heap. Because lime is more soluble than cement, detoxification of the heap becomes much faster and less costly for the mine relative to rinsing cement alkalinity. The following graph compares the detoxification rate of cement and polymer over a 33 day cycle.

Jan 1, 1993

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of ' an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

By Robert R. Munro

Traditional aggregate sources, that is the riverbeds, the alluvial fans, located relatively close to the developing urban centers are being foreclosed to mining. As the sand and gravel reserves are depleted, those production plants are unable to secure additional adjacent reserves and are being forced to close down. The sand and gravel industry, in many respects, is its own worst enemy. We promote development, we promote the paving of streets, the building of houses, and industrial and commercial centers, and because of economics, we tend to favor those developments located close to our operations. Thus, we encourage development by our neighbors who soon become our detractors. In general, urban development is not compatible with sand and gravel mining. The neighbors don't like the view of the pits or the quarries, they complain about the "dust", about noise, about trucking . . . in general, the neighbors are not happy being close to an aggregate source.

Jan 1, 1984

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abandoned coal mines also imposes potential hazards in current mining operations since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive man-made tunnels in previous work has led to the development of a surface- operated automatic earth resistivity survey system and associated computer data processing system for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to- diameter ratios greater than ten to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting coal mine workings. The hardware and software aspects of the new system are described together with applications of the method to the survey and mapping of abandoned coal mine workings. Field tests are presented showing the detection of both air-filled and water-filled mine workings.

Jan 1, 1981

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976

By C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 RC was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique and weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure errosion it was found that there was a synergistic effect between corrosion and erosive wear. Erosive wear rates are given as a function of pH and mineral type.

Jan 1, 1984

By R. A. Deju

The Basalt Waste Isolation Project of the U.S. Department of Energy is a part of the National Was re Terminal Storage Program. Its mission is to assess the feasibility of siting a nuclear waste repository in the basalt formations which underlie the Hanford Site of the U.S. Department of Energy. The progress in all program areas is summarized in this paper. Activities conducted to date have led to the identification of possible repository candidate sites within the Hanford Site.

Jan 1, 1981

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

The Bureau of Mines, U.S. Department of Interior, is currently investigating strata interactions associated with the mining of multiple coalbeds. Strata interactions due to subsidence are a result of undermining. This study involves underground investigations at a mine where room and pillar panels are actively being developed through an area of the Sewickley Coalbed which was subsided by undermining of the Pittsburgh Coalbed. Research to date indicates that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. Consequently, this has led to major roof falls in the active panels, resulting in considerable production delays and supplemental roof support costs.

Jan 1, 1985

By R. M. Campoy

Mexico's mineral wealth has long been recognised and indeed has played a historically significant role on a world scale. The dynamics of the Mexican mineral industry have experienced a dramatic transformation especially over the last two decades. This transformation has mainly been instigated by the high growth rates and industrialisation of the Mexican economy since the 1960's. This paper focuses on the base metals sector of the industry which represents one of the major contributors to this transformation. The objective is to present a brief base metals review and to discuss some recent occurrences which pertain to this sector of the industry. This is followed by a discussion of mining's relevance in the current economic situation in Mexico. With this overview as background, the investment climate, primarily from a domestic investor's perspective and secondly in terms of foreign investment, is discussed. Finally, some recent government initiatives, including tax and accounting changes, are outlined. Any one of the sections of this paper can easily be developed into an extensive and indepth analysis; however, the intention of this paper is to provide the reader with a broad overview of the topics discussed.

Jan 1, 1985