Search Documents

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific and the U.S. National Institute for Occupational Safety and Health (NIOSH) combined efforts to evaluate an in situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was preloaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both realtime and time-weighted-average approaches. The real-time measurements were performed with a Model AE33 aethalometer, and filter samples analyzed by the NIOSH 5040 method were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82 to 89 percent. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the aethalometer were higher, possibly due to differences in the performance of the size selectors used for the two methods: impactors versus cyclones. More research is required to develop a robust correlation between the two methods to support the use of the aethalometer in future mining applications. The advantages of the aethalometer are that it can measure and record DPM levels for weeks at a time and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally, such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise in reducing DPM concentrations in the mine environment.

Mar 1, 2017

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By Joseph J. Yancik

An exchange of coal mine specialists was made with the USSR under an "Agreement on Exchanges and Cooperation in Scientific, Technical, Cultural, and other Fields for 1972-73," which was signed by President Nixon and Chairman Breshnev on April 11, 1972.* This exchange, in the field of coal mine safety and scientific research in hazard control technologies, was one of 16 technical exchanges covered under the above agreement. A six-man USA delegation visited the Soviet Union from September 9 to September 21, 1973. The delegation visited four deep mines, three in the Donets Basin and one in the Moscow Basin, a State Safety Research Institute, a Mine Research Station and associated Research and Design Institute, two Research and Design mining equipment institutes, and a Trade Union-sponsored health sanitarium. In Moscow, the delegation received a briefing on the Soviet coal industry from First Deputy Minister Vladimir Fedanov. A similar briefing was given to us on the Donets coal basin by the Deputy Minister S. Saratikyanz of the Ukrainian Coal Ministry. Lengthy technical discussions were held with the mines staff and research personnel at the institutes we visited. In addition, we had detailed discussions with key staff members of two combinats "Donetskugol" and "Tulaugol." In all these meetings, principal topics were matters of safety related to hazards associated with face mechanization, coal transport, methane gas control measures, gas outbursts, coal and rock outbursts, fire fighting add control, explosion suppression and control measures and other related hazard factors. There was also much discussion on miner training, miner's attitudes toward safety and accident prevention practices, and preparation and enforcement of safety rules and regulations. The delegation was very warmly received and constant attention was given to our needs. Our numerous questions were answered with candor although quite often in not as much detail as we would have liked.

Jan 1, 1974

By Robert J. Wright

The purpose of this paper is to propose a classification of uranium deposits that is believed to be well suited to the needs of uranium exploration and resource assessment. By way of background some observations are offered about mineral exploration in general, and uranium in particular. Attention is first given to the we of models in mineral exploration. Some general principles of mineral deposit classification, the basis for model formulation, are then considered. Finally, the uranium classification is presented.

Jan 1, 1979

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By Inkap Choi

Asbestos is a broad term embracing a number of fibrous silicate minerals. These minerals look extremely fragile, yet their fibers have a tensile strength equal to that of piano wire. Chrysotile asbestos is the only mineral that can be woven into cloth, and its fibrous structure is, if anything, even more amazing than its remarkable ability to withstand heat. Because of its unique physical properties asbestos has achieved great industrial importance, and more than 3,000 current uses are known, ranging from use in the kitchen to use in space missiles. Because their minuscule fibers are eminently respirable, asbestos minerals have also found their way into the lungs of humans, where they apparently produce serious biological effects such as asbestosis and lung cancers. 1, 2,3 Because of both their usefulness and their hazardous properties, these minerals have attracted a good deal of attention from research workers during recent years. For example, the surface properties of asbestos minerals have been studied by many investigators. 4, 5, 6, 7, 8, 9 However, even for the important mineral chrysotile, the literature data are more or less conflicting. Pundsack4 measured a PZC (point of zero charge) of 10.1; Martinez and Zucker5 measured 11.8; Chwastiak reports 10.8-11.0; and Raddick measured three sepa-rate apparent PZCls at about pH 8.3, 10.0 and 10.9. More recently Trivedi8 reports 10.11. Naumann and Dresher9 have studied surface charge enhancement of chrysotile by metal ions, and describe how the mineral reacts with contaminantions. In the present paper, the mode of dissolution of magnesium and hydroxyl ion from asbestos minerals placed in water was studied by kinetic experiments involving rate at which these items leave the minerals. Also, some study was made of interaction between dissolved species.

Jan 1, 1972

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By Harold L. Lovell

The current interest in sulfur recovery from coal measures is indicated by a recent report prepared for the Public Health Service (1) It was noted that the concentration of pyrites to a product containing 42-48 percent sulfur should be relatively easy with present equipment. It was also pointed out that a utility potential exists for the high-grade iron concentrate which results as a by-product of the consumption of pyrites in the acid-making process. However, economics, marketing characteristics, location, transportation, pyrite levels and coal characteristics all strongly influence the feasibility of fostering industrial development of such processes. The extent of pyrite recovery and product quality is intimately related to pyrite particle size and its degree of liberation, a consideration usually given greater emphasis in metal ore preparation than in processing coals. Consequently, fine crushing to nearly 20 mesh probably will be essential for maximum practical processing. It appears that any process separating pyrites from a coal must involve a reprocessing of the normal preparation plant refuse, although some yields can be attained from certain existing operations as products from, a shaking table or a jig. Further, the existence of millions of tons of coal refuse cannot be ignored as a mined source of raw materials. The recovery of saleable products from such wastes, although untried on a large scale under current conditions, not only offers a realistic source of sulfur but also would achieve a secondary refuse with the minimal contents of substances which incite and propagate the burning of organic and inorganic combustibles. These silicate materials, thus beneficiated, also offer some potential for economic utilization. Some significant tonnages of pyrites have been produced from coal measures in the past, but the experience was, in general, not consistent with current coal preparation practice. The processes involved did not include cyclones and heavy media; nor were they carries out under the sociological environment concerned with pollution as exists today.

Jan 1, 1967

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By Mir Ahmad Mohammadi

Land uplift due to mine flooding has become a significant challenge with extensive historical mining activities, particularly in Germany’s Ruhr district. The cessation of coal mining operations has led to a gradual rise in groundwater levels, altering geotechnical and hydrological conditions and causing surface uplift. This study develops a system dynamics (SD) model to investigate the dynamic interactions of influential variables such as groundwater levels, total stress, porosity and permeability with land uplift over time. The model integrates causal loop diagrams (CLD) and stock flow diagrams (SFD) to comprehensively understand the system’s behavior. SFD illustrated that for a 10 percent increase in groundwater level, the land uplift increased by about +6 percent, and a rise of 200 percent in total stress caused an 18 percent increase in effective stress, which decreased the land uplift by about 20 percent. This study highlights the importance of dynamic modeling in informing land-use planning and mitigating the long-term impacts of land uplift after mine closures.

Mar 1, 2025

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015

By M. R. Peterson

The U.S. Bureau of Mines (USBM) is investigating alternative methods to strip metal-loaded solvent extractants. Hydrolytic, precipitation, and hydrogen pressure stripping all recover metal or metal salts directly from the organic solvent extractant. Pure metals, metallic oxides, or metal salts can be formed, allowing direct production of value-added products. Aspects affecting commercial application are emphasized, including metal recovery from actual ore leach solutions, particle size control, organic modifier and diluent effects on stripping and metal recovery efficiencies, metal grade, seed addition, mixing intensity, recycling efficiency, and reactor plating. Metal separations from copper ore leach solutions and complex waste leach solutions were examined.

Jan 1, 1995

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018