Search Documents

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Y. J. Wang

The concept of subsystem characteristic curves for multiple-fan ventilation networks is presented through the construction of characteristic curves for two-fan, series-parallel networks. By considering fans as the individual network branches, the multiple-fan network is viewed as consisting of two components: any one fan branch, which is called the reference fan branch, and its associated subsystem. Thus, F subsystems can be designated for the network with F fan branches. Each subsystem contains one or more fan branches. The subsystem characteristic curve is the pressure-vs.-quantity curve of the subsystem. As illustrated in the example networks, the subsystem characteristic curve is not a strictly increasing curve and does not pass through the origin. The intersection of the characteristic curves for the subsystem and the reference fan branch represents an operating point. Multiple intersections therefore represent multiple operating points.

Jan 1, 1994

By Y. M. Jiang

From underground instrumentation data and from direct observation of longwall panels, it was demonstrated that growth of the main-roof overhang causes an extremely high roof weighting on the face supports. This can result in catastrophic effects on the supports when the roof-weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on the characteristics of main-roof breakage and its effects on shields at different locations along the face. The study was based on monitored shield data, theoretical analysis and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed to define the main-roof failure modes and to understand the maximum roof-weighting intensity imposed on the shields. From this study, it was found that the effects of main-roof breakage on shields are chiefly related to the shield's initial-setting condition and to the final failure mode of the main roof.

Jan 1, 1996

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1988

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By I. J. Lin

The effect of various types of structural modification on the critical micelle concentrations (CMC) and hydrophile lipophile balances (HLB) of certain surfactants has been considered. Using the concept of effective chain length for the substituted species, an index of hydrophobicity (I) has been defined. It is hoped that such an index will allow one to choose surfactants for particular purposes in a less arbitrary fashion than heretofore.

Jan 1, 1973

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written which aid in the design process in the academic arena and should also have industrial applications. The programs described include a dragline cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program and an overburden volume and coal tonnage sequencing program.

Jan 1, 1985

By Hussin A. M. Ahmed

Oxidized coals are difficult to float. Therefore, in this paper, a special flotation procedure was investigated for upgrading this type of coal. The procedure is called direct contact flotation. It relies on mixing dry coal either with pure (anhydrous) flotation reagent(s) or microemulsion. By applying the new direct contact flotation procedure, a coal yield reaching > 95% using anhydrous flotation reagents was achieved, but with relatively high consumption of reagents (up to 30 g/kg). This high reagent consumption may be attributed to the fines included in the flotation feed (100% less than 0.5 mm, with 40% less than 75 µm). On the other hand, the clean coal yield was found to be approximately 88% when mixing dry oxidized coal with microemulsion droplets from dodecane and dodecyl tetra (ethylene glycol) ether (C12E4) in water at a total reagent dosage of 10 g/kg. The direct contact of coal either with unhydrous reagents or microemulsion also provided a high flotation selectivity.

May 1, 2012

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By W. B. Collingwood, D. Misra, T. Ghosh, S. Bandopadhyay

Understanding the variability of sulfur and calorific value in coal seams is critical to planning mining operations and marketing the mined coal. In this study, statistical and geostatistical techniques were used to explore the underlying spatial trends present in a large coal deposit. Eight prediction models for the sulfur content of the coal seam were developed. Six of the models were created using geostatistical techniques, while the remaining two models were created using other techniques. The performance of each model was examined by conducting cross validation exercises. The results of the study showed that very pronounced trends and anisotropies were present in the sample data, which had to be accounted for in the modeling. The study found that a cokriging model using sulfur and ash is the best prediction model for predicting sulfur content in this coal reserve.

Jan 1, 2014

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By A. Metzer

When paraffinic gases (ethane, propane, butane) are used as the gas phase in flotation systems, the initial rate of flotation and recovery are generally increased as compared with air. The mechanism of the effect of paraffinic gases in flotation was studied and it was shown that they co-adsorb with the collector ions on the mineral-aqueous solution interface. The effect of this co-adsorption was interpreted in terms of apparent increase of the effective chain length of the collector by the co-adsorbed gas. Adsorption densities, contact angles and flotation behaviour were studied on the following systems: a) Quartz - dodecyl ammonium chloride - ethane and propane b) Calcite - sodium oleate - propane and butane. The positive effect of the co-adsorbed gases is a maximum at low collector concentrations or where critical conditions for flotation with air prevail.

Jan 1, 1974

By Y. J. Wang

The use of controlled recirculation began in the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually, and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a nondimensional parameter (A), which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, far and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of and the subsystem air quantity. Numerical examples are included.

Jan 1, 1997