Search Documents

By F. B. Brost

In 1976, a decision was made by Anamax Mining Company to install an unusual conveying system to transport ore 10.3 km (6.4 mi) from the new Eisenhower Mine to the Twin Buttes concentrator. The system, supplied by Cable Belt Limited of the United Kingdom, represents a radical departure from conventional belt conveyors. The driving tension is applied through two endless wire ropes driven by a single 2 240 kw (3 000 HP) drive while the belt acts only as the ore carrying medium. Full production was begun in January, 1979. Start-up problems hampered production for several months but were resolved by a joint Anamax-Cable Belt effort. The system has been operating at design capacity for 4-1/2 years, and has proven itself as a reliable, low cost ore transportation system.

Jan 1, 1984

By Harvey P. Knudsen

Case studies are presented in this paper to illustrate the usefulness and applicability of using conditional simulation in under- ground coal mine planning. Conditional simulation is a technique developed in the last five years that allows the building of a simulated ore body (or coal deposit) model. Construction and validation of the simulated model is described in order to show how well the model reproduces the essential characteristics of the deposit. In the model, the thickness, ash, and sulfur content are known everywhere in the deposit and each variable has the same mean, variance, and spatial variability (variogram) as that variable has in the real deposit. Use of the simulated deposit in the design of drilling strategy for long range mine planning is demonstrated in me case study. Determining the potential of short term production scheduling to reduce the fluctuations of sulfur in run of mine coal is described in the second case study.

Jan 1, 1980

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

The efficient and effective utilization of hydraulic excavators relies on, among other factors, a better understanding of the formation resistance during the excavation process. Studies on hydraulic shovel excavators have focused on optimizing the digging process by considering the reaction of the boom, stick and bucket, and analyzing the resulting moments at the shovel’s front-end joints. These studies failed to understand resistive forces from a statistical viewpoint. The purpose of this paper is to develop machine-learning models capable of predicting the formation of resistive forces during shovel excavation. The shovel’s excavation was simulated in the PFC 5.0 environment using a typical field-size hydraulic shovel bucket to generate the shovel contact forces required to overcome formation resistance

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

By B. Mishra

This paper presents a rock mechanics investigation of the time-dependent behavior of the rock immediately surrounding the excavation in a hypothetical one-entry coal mine based on the geology of the Illinois coalfields Research in the area of time-dependency is almost nonexistent and, therefore, this research was performed to make inroads into this neglected research area. Numerical analysis of a typical one-entry coal mine in an Illinois basin was performed using the commercial finite difference program FLAC3D. The immediate roof of the coal entry was assumed to be a shale formation. Shale in other formations has shown a tendency to creep with time. Therefore, in this study the authors modeled the shale in the roof using time-dependent characteristics. The input properties were taken from laboratory creep tests performed on shale. Model runs were performed at different stages, mimicking the progressive excavation of the entry. The model results showed that stresses in the roof attained the limit of yielding. Using Mohr-Coulomb failure criteria, potential zones of failure were also predicted. The results showed that the current computational capacities are sufficient to explore this previously uncharted territory of ground control.

Mar 1, 2014

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By F. G. Miller

It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur, make up almost all of the total sulfur and occur in varying amounts in different coals and can vary greatly in coal of the same seam Pyritic sulfurs of 20% to 80% of the total sulfur have been reported Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and Jones (1) state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal, to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing a process, which can effectively produce in the fine fractions the efficiency of heavy media devices in the coarse.

Jan 1, 1963

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By J. R. Tonry

In the grinding of dry non-metallic materials such as rocks, ores, gypsum, lime, and cement clinker, it is recognized that only a relatively small portion of the energy is utilized for actual size reduction, and the major portion of the energy used is converted into heat. As a result, heat is generated inside grinding mills imparting to the ground product a higher temperature than that of the mill feed. In some cases, as for instance in grinding cement clinker and gypsum into finished cement, it may be desirable to keep this temperature increase within certain limits, to avoid any change in the properties of the product and, because consumers may specify a maximum temperature of the finished product for reasons associated, with the tulimate use of the cement. The actual proportions of heat and useful work are somewhat indefinite. Some tests have indicated that nearly all the energy is converted into heat, and. other investigators have found that they could account for "everything except the noise." Investigations sponsored by the American Institute of Mining and Metallurgical Engineers, and carried out with an adiabatic calorimeter, indicated that a surprisingly high 19 percent of the energy might actually be used for size reduc¬tion. However, for the purpose of the following discussion it will be assumed that: (Fig. 1) 10% is lost in motor and gears 10% is lost by radiation and convection from the mill body 10% is used for size reduction, and. that 70% of the energy input leaves the mill as heat in the ground. product. A typical example (Fig. 2) would be a 7x22-ft tube mill operating in open circuit, driven by a 400 hp motor, charged with 77,000 lb of grinding media and producing 70 bbl or 26,300 lb of cement per hour. Reducing this cement from a clinker size of 96 percent passing a No. 16 mesh sieve to a specific surface of 3,230 sq cm per gm (Blaine) will increase the temperature of the cement approximately 143F above the temperature of the feed, as explained later. If the tempera¬ture of the clinker therefore is 125F, the finished cement will be 268F, which in some cases may be too hot. : When cement temperatures approach a range during grinding where dehydration of the gypsum becomes a problem, a logical consideration would be some means of reducing the temperature before it attains the range conducive to gypsum dehydration. Regardless of the varying degrees of heat generated within the mill or mills during grindingto various finenesses, consideration of the maximum safe limit for any type of cement being ground, which may vary fromplant to plant, govern in refining the mill circuit to obtain a safe temperature range. All plants are not necessarily required to do the same cooling job, and may or may not use cement coolers following the grinding circuit. (Not discussed in this paper). In the past, various means have been employed for controlling this temperature increase, Such means have included water cooling of the outside of the mill shell; equipping the shell with cooling fins; injection of moisture inside the mill; ventilation through the mill; and., in cases of closed-circuit grinding, drawing cooling air through the classifier; the purpose in all such cases being to remove heat from the grinding system.

Jan 1, 1958

By C. H. Perbix

[On Pier D in the Port of Long Beach, California, the Port of Long Beach has built a new bulk cement distribution terminal. The facility is operated by Pacific Coast Cement Corporation, who designed the complex and leased it from the Port of Long Beach on a 40-year lease. At one bulk cement is unloaded from vessels carrying from 12,000 to 30,000 t. The unloading is performed with pig speed mechanical unloading equipment and delivered into a concrete silo complex with, a capacity of 50,000 t. From the silos, bulls cement is loaded into trucks for delivery. The facility was completed in September 1981.]

Jan 1, 1983

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By D. D. Gertenbach

"The successful commercialization of a pressure oxidation (POX) process for recovering metal values, including gold, copper, zinc, nickel and molybdenum, is the result of a carefully planned development program. The initial task involves developing one or more conceptual flowsheets, including the POX autoclave and downstream purification and recovery steps. A laboratory program is completed to determine the technical viability of the flowsheets, define the operating parameters for each step and provide information for an initial economic assessment of the process. The process is then confirmed during a continuous pilot plant program, providing engineering design data and other information for the commercial design. A well-thought-out development program has been shown to be critical for reducing the risk of commercializing POX processes. Experiences developing POX processes for refractory gold ores and copper concentrates are briefly discussed. IntroductionPressure oxidation (POX) has become a common commercial operation for processing sulfide-bearing feedstocks. These feedstocks include gold ores and concentrates; copper concentrates; nickel concentrates and mattes; zinc concentrates; and molybdenum concentrates. Drivers for the development and commercialization of POX processes include:• The high cost for pyrometallurgical processing of sulfide ores, much of which is attributed to environmental controls.• The motivation to implement safe and more environmentally attractive alternatives for sulfide ores.• The need to process increasingly difficult ores with complex mineralogy.• Improvements made over the last 25 years in POX equipment design and experience operating commercial POX plants.Although the capital and operating costs for commercial POX processing can be high, this technology is capable of rapid oxidation of most sulfides and arsenic minerals in the feed, with little noxious gases and environmentally stable iron arsenate and other iron compounds in the POX residue (Marsden and House, 2006).In POX operations, sulfides are oxidized to either sulfates or elemental sulfur in an autoclave at elevated temperature and pressure with oxygen gas. An example is the overall oxidation reactions of chalcopyrite when sufficient oxygen is present, shown in the following reactions:"

Jan 1, 2016

By SME SME

List of 43rd ICGCM 2024 ORGANIZING COMMITTEE

Jun 25, 2024

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By T. R. von Ow

The method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said that almost every decade in the last half century had its own trend. The trends were dominated by the market demand, the advanced process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology. The increasing size of the ring geared mills in the last years requires more awareness on the drive train solution. Special attention must be paid to the mechanics and the requirements of the power grid. Operational challenges such as soft starting and controlled operation as well as the protection of the equipment have gained importance. Frequency converter drive solutions dedicated to single or dual pinion ring-geared mills offer significant advantages over conventional drives due to their application specific features and controls. Solutions with low speed motors as well as high speed motors cover all possible configurations available for ring geared mills.

Jan 1, 2010

By John T. Cantwell

INTRODUCTION The process engineer usually is responsible for the design operating philosophy and/or day-to-day operations of a process. Since instrumentation is an integral part of the operation, it is essential that engineers understand the general capabilities of the different types of control equipment available. Many "noncontrol" engineers have become involved with instrumentation for machinery monitoring and control as well as other plant applications. The advent of the microprocessor has led to significant changes in control, both in systems configurations and man-machine interfaces. Today's concept is called simply "distributed control." What is distributed control? Distributed control is exactly what the name implies; the control system is divided into several functional segments and spread out to cover a process. The systems are distributed for physical, functional, and risk reasons. Before delving further into the specifics of distributed control, let's look at the evolution of control systems to see how we got here. Instruments initially were located near measurement and control points in the field. Operators physically had to go to the instrument to change setpoints or take measurements. As processes became more complex, it became evident that a central control area was required. This allowed an operator to monitor and control many variables. The operator's effectiveness was increased dramatically, which resulted in greater efficiency, better quality control, and lower personnel requirements. At the same time, plants became much larger, control applications became more complex, energy became expensive, and the industry became more competitive. All of these factors placed pressure on process and production engineers to get the most for the money. The result was a continuing push to put more instrumentation into a central control room to maximize efficiency and productivity and minimize manpower. This chapter deals in some detail with devices for measuring physical and chemical properties of coal; devices for measuring the weight and weight-rate of flow of coal; devices for the monitoring and control of conveyor systems, solids inventory, fluid flow, liquid level, density, and specific gravity. These instruments have a multitude of uses throughout a coal preparation plant. The discussions cover advancements in "on-line analysis," nuclear control devices, and distributed control using microprocessors, mainframes, and soft-

Jan 1, 1991