Search Documents

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer'. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public's legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By Edward Holloway

The basis for the selection of the ultimate pit for an open-pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau while the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-mak-ing range is significantly reduced and the process for select-ing the ultimate pit becomes more consistent, replicable and defensible. The technique outlined in this paper provides an approach to including risk in the process used to select the ultimate pit.

Jun 1, 2024

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By Peter G. Chamberlain

Novel and innovative mining methods are attracting the attention of mining engineers at an unprecedented level. Historically, the US mining industry has responded rather conservatively to new technology. The financial difficulties affecting the domestic mining industry in the early 1980s changed attitudes toward new technology. The market contraction during that period, coupled with an expanding world mine capacity, created a serious oversupply of many raw mineral products. Many mining companies found that retaining a share of world markets while making a profit required drastic cost-cutting measures.

Jan 1, 2008

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

A Mark IV surface force apparatus (SFA) was used to conduct direct force measurements between mica surfaces in dodecylamine hydrogen chloride collector solutions at varying pH levels. It was found that long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40 to 0.48 nm2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that, in the pH range of 8.0 to 10.3, the maximum flotation recovery of quartz may be attributed to the appearance of a long-range hydrophobic force, which, in turn, can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1998

By Larry Taylor, Thomas Zdeb, Brian Jacobs, Dennis Jensen

Subway tunnels proposed for the Los Angeles County Metropolitan Transportation Authority (LAMTA) East Side Extension are to be excavated below the groundwater through an area of Los Angeles, California with dissolved hydrogen sulfide concentrations in excess of 200 mg/L. To address unique construction and worker safety issues, bench scale and field pilot test studies were conducted to evaluate various mitigation alternatives including in-situ oxidation by chemical injection, slurry pH adjustment to suppress H2S evolution, and chemical treatment to remove the H2S from the slurry and muck material. The results provided the basis for detailed hydrogen sulfide control specifications for the contractor.

Jan 1, 1999

By J. Villeneuve, M. A. Reute, E. Verhoe

The objective of EU waste policy is to reintroduce used materials into the economic cycle, especially by recycling, or to return them to the environment in a useful state or at least a harmless state. To support decision-making in complex systems, the standardised ISO 14040 life cycle assessment (LCA) method can be used to quantify and to interpret the environmental repercussions of (changes in) a product system from cradle to crave related to a functional service unit. The use of the standardised LCA method at European level can be characterised as a damage-oriented or top-down method, which is often used in product design. Winning, extraction and processing of metals are part of the interconnected worldwide metals production system linked to product design, manufacture and recycling. This complexity cannot be dealt with using LCA. This paper will discuss a dynamic model that deals with this complexity, at the same time providing detailed bottom-up insight into the complex web of materials referred to as Metal Ecology. An example on the replacement on lead in solders will be discussed to illustrate this.

Jan 1, 2005

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By John E. Anderson, Charles A. III Cravotta, Eleanora I. Robbins, E. Terrance Slonecker, Gordon L. Nord

Remote sensing is being tested for its ability to identify the severity of impact on streams that are subjected to contaminated mine drainage (CMD) in the Southern Anthracite Coalfield of Pennsylvania. Airborne digital multispectral video images of acidic and near-neutral CMD are being compared with field spectra, water chemistry, mineralogy, and microbiology. Spectral differences in the visible region of the electromagnetic spectrum are caused by the presence of schwertmannite in the acidic precipitates and ferrihydrite in the near- neutral precipitates. The acidic CMD averages 1,500 mg/L sulfate and has bacteria coated with schwertmannite; the near-neutral CMD averages 87 mg/L sulfate and has bacteria coated with ferrihydrite.

Jan 1, 2000

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

By G. Wang, L. R. Moore, Y. Xiong, J. Gu

"Quartz is the second most abundant mineral in the earth’s crust. Not only does quartz have many valuable industrial applications, it is also one of the most concentrated gangue minerals encountered in the processing of other minerals. Minerals such as hematite, apatite, calcite, feldspar, barite, and many more. Numerous applications of industrial minerals are sensitive to the hardness and abrasiveness encountered with quartz minerals, while other applications may lead to processing challenges for the end user. Therefore, process and chemistry optimization must be applied to ensure optimal grade is obtained for these valued industrial minerals. Extensive studies have been conducted in processing various industrial minerals, thus achieving a range of quality specifications, which entailed the application of ArrMaz’s CustoFloat and CustAmine collectors towards the separation of quartz from other minerals. INTRODUCTION Industrial minerals often have the misfortune of the gangue mineral being very similar in surface charge, and coordination properties, to that of the mineral of interest. An example is seen in phosphate beneficiation, when dolomite can be a gangue minerals (Table 1). Therefore, the development of processing reagents are quite complicated. Some minerals, like clays, may be washed away. However, most require the manipulation of the pH, in efforts to fine tune the system to the narrow difference in isoelectric points of the different minerals, as well as the knowledge, and resources that are necessary to exploit the differences to yield and an optimal grade/recovery. In some cases, the application of a depressant may be required, such as the phosphoric acid commonly applied to achieve the optimal balance of grade/recovery for phosphate from a mineral with elevated concentrations of dolomite (Wang, 2016), or the application of hydrofluoric acid to assist in producing feldspar product from a mineral rich in quartz (Heyes, 2012).ArrMaz's CustoFloat and CustAmine product lines have successfully been applied to the processing of industrial minerals for more than 50 years. Applications include, but not limited to phosphate, sand (glass, foundry & high purity quartz), clays (feldspar, kaolin, etc.), and many carbonaceous and sulfate minerals. The successes of these 50 years are largely due to ArrMaz's ability to tailor make the processing chemistries to fit the ever changing and declining mineral feed grade and variations in water quality (Moore, 2015; Moore, 2016). This technical knowledge of mineral processing is strongly complimented by the intimate service programs in place at many of the beneficiation plants."

Jan 1, 2018