Search Documents

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By D. E. Cameron

The Cannon mine, located in north-central Washington is mining gold hosted in silicified Eocene-age arkosic sediments arrayed along a regional strike-slip fault system. Branches of the Eagle Creek fault have broken the Chumstick Formation into blocks and wedges, and have caused intense deformation of stratigraphy in the mine. Mineralization at the Cannon mine (B-Reef) and O-Reef (L-O mine) is a bulk silicification with high grade cross-cutting veins containing principally electrum, silver sulfosalts and pyrite in a gangue of quartz, adularia and calcite. Orebodies have very irregular shapes, but tend to follow stratigraphy and high-angle pre-mineral fault breccias and splays developed adjacent to the major faults. Both B-Reef and O-Reef occur at significant bends in the regional trend of major fault strands. Mean gold grades decrease upward from near sea level to the 300 m elevation at the Cannon mine. A new discovery, the A-Reef is hosted by a moderately dipping structure which is at a low angle to bedding. Fluid inclusion studies of B-Reef ore zones indicate dilute ore-bearing fluids boiled at temperatures between 185 and 2850 C at a depth of 1 km. Many ore zones are bounded by sheared mudstone and claystone and a much broader halo of argillic alteration comprising illite, smectite and sericite. Trace and major element analysis by ICP-ES for 33 elements, LECO for S, Hg by CVAA and gold by AA-FA shows dispersion patterns hundreds of meters outward from the known orebodies in the Cannon mine. Geometric mean comparisons, hierarchical R-mode cluster analysis and single element spatial plots show that Hg, As, Sb, S and K/Al compose a suite of elements which are significantly dispersed away from, and increase toward mineralization. Ba, Ca, Na, Mn, V and Zr decrease toward mineralization. The suite is more selective than gold with respect to known mineralization within the exploration area.

Jan 1, 1992

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By E. Lee Bray

"Editor’s note: The editors thank those who make this annual issue possible. A special thank you goes out to the Industrial Minerals Annual Review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech Geo, is the industrial minerals annual review editor. Edgar Blanco, member SME, of Freeport- McMoRan, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• NickTushar Gupta and Sallie Gaillard, of the USGS, members SME, agricultural materials.• Abhishek Choudhuryand Xihui Yin, members SME, of Montana Tech and Kemira, repectively, ceramic and refractory materials.• Bobbi Strange and Riddhika Jain, members SME, of Outotec, Martin Marietta and Outotec, respectively, chemical raw materials.• Snehamoy Chatterjee, Alyssa Kendir and Alind Chandra, members SME, of BMT, Universityof Kentucky and Michigan Tech, respectively,construction aggregates.• Subham Verma, Gauran Soni and Freddy Sime, members SME, fillers and pigments.• Kaiwu Huang, Thomas Hilderbrand and Ricardo Santander members SME, of Virginia Tech, Thiele Kaolin and Carbo Ceramics, respectively, sorbents, filters and process aids.• Rhaghay Dubey and William Rapier, members SME, of Outotec and a consultant, respectively, specialty minerals.On behalf of ME readers, the editors thankTwo U.S. alumina refineries produced an estimated 1.5 Mt (1.65 million st) of alumina from imported bauxite in the United States in 2018. The 500-kt/a (550,000-stpy) refinery in Burnside, LA, owned by Almatis Inc. produced specialty alumina used in the abrasives, ceramics, chemical and refractory industries. The 1.2-Mt/a (1.32 million-stpy) refinery in Gramercy, LA, owned by Noranda Alumina LLC produced alumina mostly for use in aluminum smelters but also produced specialty alumina. An upgrade project at the Gramercy refinery to convert 200 kt/a (220,000 stpy) of capacity to produce more profitable specialty alumina was completed in the first half of 2018, and another project to increase capacity was started but a completion schedule was not available. The amount of new capacity was not disclosed, but it would be used to produce nonmetallurgical grade alumina. The 2.3-Mt/a (2.5 million-stpy) refinery in Point Comfort, TX, which was temporarily shut down in March 2016, remained closed throughout the year."

Jul 1, 2019

By J. O. Marsden, C. Green

In 2003, a high-temperature pressure leaching circuit to treat copper sulfide concentrates was commissioned at the copper/molybdenum operation at Bagdad, AZ. In late 2007, a medium-temperature pressure leaching circuit was commissioned at the Morenci mine in Arizona. The Morenci circuit was shut down in mid-2008, following a fire in the autoclave circuit. The onset of the global financial crisis in late 2008 resulted in significant changes to the operating profile in the Southwestern United States with respect to concentrates production, concentrates treatment, acid production and acid consumption. As a result of these changes, the Morenci concentrator was shut down, and the pressure leaching circuit remained offline. In late 2014, the increasing acid requirements in the Southwestern United States prompted a reevaluation of the Morenci concentrate leaching facilities. As a result, the pressure leaching circuit was restarted in high-temperature (200 °C) mode in May 2015 and has operated successfully for three years since recommissioning. This paper describes the current pressure leaching circuit configuration and the factors leading to the successful application of copper sulfide concentrate leaching at this location.

By E. Krist

The newest addition to the Anamax Mining Company's Twin Buttes copper producing complex is a by-product uranium extraction plant which was placed into service in February 1980. The plant is unusual in that it is placed internal to the copper countercurrent decantation, solvent extraction, and electrowinning plant. The plant reached full production within a month and, to date, has produced continually above design rates.

Jan 1, 1981

By P. C. Thakur

Methane has been a hazard since the beginning of coal mining and has influenced, more or less, every aspect of coal mine design. It is receiving increased attention lately because the rate of methane emission in coal mines is increasing as increasing demand for coal leads to exploitation of deeper seams and the use of higher productivity equipment. Consequently, the government and private industries have directed a great deal of effort towards understanding and solving the problem of methane emission in coal mines. In the United States, Consolidation Coal Company has pioneered research in this area since the early 1950's.1 Currently this work is being expanded by Consol through the Mining Research Division of the parent company, Continental Oil (Conoca), to find new techniques for degasification of virgin areas as well as control of methane in gob areas. Basic reservoir properties of coal seams, such as gas content, reservoir pres-sure, diffusivity, porosity and permeability are better understood today largely through the efforts of the U. S. Bureau of Minese2,3,4 It is possible now to identify and model the basic mechanism of gas emission from coal and to forecast steady as well as unsteady state emission of methane in coal mines with some degree of reliability. Combining this knowledge with any ventilation simulator should often identify problem areas in advance and permit adequate methane control measures to be planned.5 Another recent innovation in methane control is the horizontal hole drilling technology. The U. S. Bureau of 1-1ines and the Mining Research Division of Conoco have independently developed techniques for drilling horizontal holes 300 to 600 m deep6 The Bureau's method employs a rotary drill string while Conoco uses a non-rotating string with a down hole drill motor. It is the authors' view that the latter provides more positive control on bore hole deviation both vertically and laterally and appears to be faster, though somewhat more difficult to operate. The rate of methane emission depends on a number of factors which can be broadly classified in two groups. These are (1) the basic reservoir properties of

Jan 1, 1977

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By James S. Browning

The Mineral Resources Institute of The University of Alabama conducted research on the removal of sulfur from coal using a combination of gravity concentration and flotation methods. The research utilized the gravity and centrifugal force capabilities of the Humphreys spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphreys spiral coal concentrate removed additional sulfur and ash to yield products that conform to Federal air quality standards for sulfur oxide emissions. The clean coal products recovered by the combined process contained 7.7 to 8.0 percent ash, 0.12 to 0.16 percent pyritic sulfur, and 0.78 to 0.96 percent total sulfur. Pyritic sulfur rejection by the process was about 95 percent. In addition to obtaining good recoveries of high quality coal the tests demonstrated that the pyrite in the wastes could be isolated as enriched flotation products by the combined gravity - flotation apporach. Pyrite concentrates analyzing 25 to 33 percent sulfur were recovered. Potential benefits of the pyrite flotation step are recovery of a product of possible market value and the elimination of the pyrite from the waste ash which could be a potential acid water problem when impounded.

Jan 1, 1981

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By J. G. Groppo

Eastern U.S. oil shale contains approximately 10 to 12 gallons of oil per ton and 7 to 10 percent pyritic sulfur. Physical beneficiation of these low grade shales using froth flotation provides a high grade material which will make extraction of oil more economically attractive. The Alabama oil shale used in the present study contained 16.46 percent organic carbon and 14.5 gallons of oil per ton as determined by Fischer assay. Liberation size of the kerogen was estimated at 10 /-Lm. 'Ken-Flote' column flotation technology provided a high grade concentrate containing as much as 60 percent organic carbon, however, carbon recovery was about 60 percent. Carbon recovery was improved to 75-85 percent while maintaining concentrate grades in excess of 40 percent carbon by providing longer retention time in the column which facilitated effective bubble-particle collision and attachment.

Jan 1, 1993

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Muhammet Mustafa Kahraman

Despite technological advancements and organizational adjustments, lost time accidents are major issues in occupational safety. However, there is very limited work that focuses on variables influencing days lost as a result of occupational accidents. In this study, decision tree and artificial neural network methods were used as machine learning techniques to investigate the impact of factors on accident lost day duration. Degree of injury, worker age, and worker activity were found to be the top three variables impacting loss of time from work. It was also identified that the mining method, location, and nature of injury had a moderate influence on duration lost due to occupational accidents. However, worker experience and ore type did not have any significant impact on the duration, which is an unexpected result. These results confirmed that some accident factors that might have a large influence on the number of mine accidents can be less critical when it comes to accident lost day duration.

Feb 3, 2021

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

Geostatistics is well known as a tool for ore reserves calculations at the exploration stage. The goal of this paper is to show geoscatistics can also contribute to productivity gains, allow better selection of the mining methods and better control of the grades during production. The first two examples show how geostatistics can provide sophisticated models, using conditional simulations and the use of them for simulations or optimizations of mining processes. A third example will show how to use geostatistics for short term planning in a large polymetallic vein type mine.

Jan 1, 1983

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

By W. M. Cross

The hydrophobic character of sapphire surfaces in SDS solutions was examined with respect to the aggregative nature of the adsorbed surfactant phase. It was found that, at equilibrium, sapphire surfaces having adsorbed SDS bi-layers exhibited no contact angle. Conversely, when the adsorbed SDS was found to be mi-cellar in nature, sapphire surfaces developed significant hydrophobic character. The surface states as detected by Fr -IRIIRS conformational analysis were found to be reversible with temperature. The variation in adsorption density with temperature was studied by in situ Fr-IRIIRS. The isosteric heat of adsorption was calculated to be -1.6 kcal/mole. Although the adsorbed SDS was found to undergo a reversible phase change between 25 and 32°C, similar to SDS in solution, the extent of adsorption was not reversible with temperature.

Jan 1, 1993

By O. Babak, O. Leuangthong, M. A. Cuba

Integration of data from multiple sources and/or multiple scales is a common, yet challenging aspect of geostatistical resource modeling. Common approaches to data integration are based on a cokriging framework that assumes a consistency of scale in the information that leads to a requirement to composite the data prior to model construction. It is well known that the geostatistical model parameters are scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the semivariogram that should be used in model construction and/or the assessment of volume-variance relations as it affects resource estimation. This paper reviews and compares two different approaches for semivariogram upscaling. The first approach is the scaling laws. It is an empirically derived approach, involving several simplifying assumptions, one of which is a strict assumption of invariance of the semivariogram shape. The second approach is a theoretically derived direct upscaling of the semivariogram. This approach has been around for a number of years, but is seldom implemented due to software limitations. In this paper, we present a numerical integration approach to facilitate direct semivariogram upscaling. The advantage of direct upscaling over the scaling laws approach is shown by considering a synthetic example and a case study. Further, in the case of multiple codependent random variables, the extension of the direct semivariogram upscaling to the cross semivariograms is derived and an upscaled consistent linear model of coregionalization is presented.

Jan 1, 2013