Search Documents

By Louis W. Cope

Many Americans have seen Greenland while flying over it on their way to or from Europe. Few have visited this largest island in the world. Portions of the 20 percent of the territory that are not ice-covered are highly mineralized. Greenland could become very productive if the present interest in exploration increases. The people and Greenland’s history The population of Greenland is 57,000. Twenty percent are Europeans, mainly of Danish decent, while 80percent are native Greenlandic or mixed Greenlandic-European. The native population is the same as the Inuit of the Canadian Arctic. They speak the same language.

Jan 1, 2004

By W. G. Pariseau

This contribution describes rock mechanics features of the Davis Cavern at the former Homestake Mine in Lead, South Dakota, U.S.A. The mine is located in the northern Black Hills of South Dakota. In 2003 and again in 2008, the mine site was recommended for development as a national Deep Underground Science and Engineering Laboratory (DUSEL) in cooperation with the Sanford Underground Science and Engineering Laboratory under the South Dakota Science and Technology Authority (SDSTA). The original Davis Cavern was excavated about 9.1x16.8x9.7 m high (30x55x32 ft high) in 1965 (Mitchell 2009) at a depth of 1,478 m (4850 ft). The purpose of the cavern was to house apparatus for detecting solar neutrinos. The experiment ultimately proved successful and earned R. Davis a share of the 2002 Nobel Prize in physics. Recently, a new experiment (LUX=Large Underground Xenon detector for dark matter particles and WIMP's=weakly interacting massive particles) was proposed for the Davis Cavern that required an increase in height of 2.4 m (8 ft). For many years, the Homestake gold mine was the deepest operating mine in North America. Development extended to the 8000 Level (2,438 m). The mine closed in 2003. Pumps were shut off and the water level rose to the 4350 Level, about 150 m (500 ft) above the Davis Cavern. Some six years later after selection for DUSEL proposal development by the National Science Foundation (NSF), access to the 4850 Level and the Davis Cavern was regained. Pumping has lowered the water level to well below the cavern floor. Figure 1 shows the layout and location of the Davis Cavern (Cavity). Detector tank, supporting steel, and so forth were subsequently removed. The cavern was re-supported and new access was developed. By August, 2010, 13,000 ft3 had been removed during enlargement and renovation of the Davis Cavern. Figure 2 shows the detector tank under construction in 1965.

Jan 1, 2012

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By K. A. Allison, D. R. Van Orden, R. J. Lee

Continuing analysis of environmental samples for asbestos content has resulted in the misidentification of non-asbestos amphibole particles as asbestos fibers. These errors have received wide publicity (such as in the asbestos-in-crayon story) and have caused unnecessary reformulation of products. The primary cause of these errors has been a poor understanding of mineralogy and analytical techniques among the many asbestos laboratories that arose following the passage of the AHERA regulations. Presented here is a procedure based on published data that can be used to correctly classify an elongated particle as asbestos or as non-asbestos.

Jan 1, 2005

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005

By Georgene Renner, William R. Yernberg, Steve Kral

ABB offers complete electrical revamps of mining shovels with ac or dc drives, drive control, frequency converters with insular gate bi-polar transistor technology, intelligent control packages and visualization. Many of the world’s shovel excavators and draglines (walking excavators) were built in the1980s. After 15 to 20 years of round-the clock operation in openpit mines, these machines start to feel their age. Electrical parts are particularly vulnerable. Their performance deteriorates and availability and productivity fall. Even with regular ser-vice and maintenance, a machine of this age will accumulate 400 hours of unscheduled downtime a year. The need for a replacement becomes pressing, but the expense is often prohibitive.

Jan 1, 2005

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

By J. Burgess Winter

It is an honor to present the lecture in honor of Daniel C. Jackling, the developer of the technology of copper mining that we continue to use 100 years later. He made a dramatic breakthrough in the early part of this century in the development of bulk-mining methods for large, low-grade porphyry copper-sulfide ore bodies. At Magma Copper, we are particularly proud that the Jackling Award states we have "made significant contributions to technical progress." Before Jackling's time, copper mining had exploited with primitive equipment very high-grade underground ore bodies and high-grade open pits. During the 20th century, the situation changed. Three significant innovations occurred within about 10 years around the turn of the century. In 1903, Jackling's concept of large-scale mining with steam shovels and rail haulage was implemented at the Bingham Canyon mine in Utah. Eighty years after the introduction of rail haulage, the mine converted to truck haulage with large-capacity high-efficiency haul trucks and reduced the stripping ratio from 3.5:1 to less than 1:1.

Jan 1, 1995

By Sigurd L. Lamhauge, Karl Gunnar Holter, Svein E. Kristiansen

An innovative sprayable waterproofing membrane in combination with the traditional Nordic method of waterproofing with polyethylene foam sheets was used for the waterproofing of the tunnel. The sprayable membrane was integrated in the final sprayed concrete lining in a sandwich structure, hence constituting a composite water-proof lining based on sprayed concrete. The spray able membrane was applied in areas with small to moderate water ingresses, making up approximately 50% of the total area requiring waterproofing in the tunnel. State-of-the-art application technology with a computerized spraying robot was used. A consistent application of the required thickness at a high speed was thereby achieved.

Jan 1, 2007

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By H. Walqui, C. Noriega

Southern Copper Corporation (SCC) is one of the world’s largest copper companies and is finishing the modernization of the Ilo copper smelter. A single ISASMELTTM furnace will start smelting 1,200,000 tons per year of concentrate at the end of 2006. Three existing Peirce Smith converters are being upgraded plus a new one for converting the matte to blister copper is being installed. Two new anode furnaces and a twin anode casting wheel have being operating since January 2006. This represents one of the main changes in the process because the final product of the smelter is now anode copper instead of blister copper. A new oxygen plant, acid plant, and others facilities are in the ramp-up stage. This environmental project will ensure that the new smelter will comply with the environmental regulations of Peru by the end of January 2007. This paper summarizes the background to the modernization project, describes the different stages of the project including engineering, procurement and construction, describes the main areas of the new copper smelter and also the pre-operational testing, commissioning and start-up of them. This is a brown field project with a target of reducing as much as possible the production losses of the existing operation. This paper presents the details of the development of the Ilo Smelter Modernization Project and explains the main aspects of the new facilities, the products to be obtained and the associated facilities for their commercialization, including a Marine Trestle for bulk acid exportation.

Jan 1, 2007

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By M. I. Brittan

Cyanide leaching of two West African gold ores was studied in multiple laboratories to provide process-engineering data for plant design purposes. Unusually slow leach extraction kinetics were observed using routine cyanide leach test procedures with pregnant solution monitoring. Carbon-in-leach testing, however, showed normal rapid kinetic behavior, with the same ultimate gold extractions being reached in much shorter elapsed times. Kinetic curves based on washed solids assays also exhibited more typical leaching characteristics. The results bore all the hallmarks of some equilibrium inhibition of the leaching. It was surmised that ore gangue components were responsible for weakly adsorbing gold-cyanide complex reaction product, thereby holding up soluble gold in the solid phase. The term ?preg-borrowing? was coined to describe the reversible phenomenon and distinguish it from irreversible preg-robbing. The two ores investigated may represent an extreme form of a more general effect that in most instances might pass unnoticed. The effect can lead to misinterpretation of kinetic leach curve data and underestimation of calculated ore head grades.

Jan 1, 2008