Search Documents

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By Barbara C. Schickner

The long-awaited COSMAR study prepared under the auspices of the National Academy of Science reaches one emphatic conclusion that has been enthusiastically seconded by the mining industry: The 1977 federal surface mining act is "poorly suited" as a vehicle to regulate noncoal mining. Though the industry greeted the report with approval, the weight it will carry and the extent of its impact are yet to be felt. The COSMAR report makes no recommendations-that's a job left to the Administration's Council on Environmental Quality-and the prospect of legislation still hovers. For a closer look at the study, MINING ENGINEERING talked to COSMAR committee chairman James Boyd, a well-known presence in the mining arena for over 50 years. After highlighting some of the study's major points, Dr. Boyd comments on the report's impact and possible repercussions. Dr. Boyd, for those readers who haven't seen the COSMAR report, would you summarize some of its major findings? The committee analyzed the surface mining act to determine if it was applicable to noncoal mining and found that there were provisions of the act that either could not be met by existing technology or would be extremely difficult and not necessarily beneficial to adapt. We found that most noncoal mineral mines, despite their obvious diversity, can be considered in two major groups: 93% of all mines move 45% of all materials mined (mostly small units mining construction materials); and the few gigantic regional operations (2%)-copper, iron, phosphate, and uranium mines-that move 50% of the material. With few exceptions, neither of the two groups is amenable to the coal mining practices addressed by the act. The strip mine law was designed for coal mining, where land is regraded, revegetated, and returned to usefulness. In contrast, construction mineral quarries supply local needs for decades, remove most of the material from the immediate vicinity, and cannot be returned to their premining uses (though they have innumerable other valuable uses). The nation's huge mineral deposits require enormous capital investments, are vital to the nation's economy, and can take centuries to exploit. Any attempt to return these locations to premining use would be illogical. Pebble phosphate in Florida and red-bed copper in Oklahoma come near to meeting the conditions contemplated in the act. In addition to COSMAR's basic finding, the study also makes the following points: •Mining uses a relatively small part of the land resource, in contrast to

Jan 4, 1980

By G. T. Adel, J. D. Miller, C. L. Lin

Washability analysis determines the maximum separation efficiency that can be achieved in the operation of coal preparation plants. Unfortunately, there are no on-line techniques for determining this most fundamental information. It now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. This paper presents the results for the development of a CT-based, on-line coal washability analyzer. The development of appropriate hardware and software necessary to adapt a CT analyzer for use in determining coal washability is discussed. Testing of the analyzer using well-characterized coal samples is presented.

Jan 1, 2000

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By Y. Luo

In designing and operating underground room-and-pillar coal mines, it is always difficult to achieve a good balance between preventing surface subsidence and achieving high recovery ratio. In this paper, a design methodology applying the pressure arch theory is proposed, and the principles and mathematical models involved are detailed. A computer program was developed to carry out the design optimization process and was applied to the examination of a documented case in which a massive cascading pillar failure had occurred over a large area in a shallow coal mine. The results indicate that the proposed design method can be applied to prevent subsidence while achieving reasonably high recovery ratio for roomand- pillar mining operations.

Jan 1, 2014

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type. (1) prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution.

Jan 1, 1978

By Stanley C. Suboleski

1977 was the modern day low point for productivity in the coal industry. At that time, no one could have predicted that the industry was about to enter a productivity rise that would continue unabated through the 1980s. Thirteen years later, the cause of this phenomenon is still not well understood. While many government studies focused on the fall in productivity from 1969 to 1977, none have been undertaken to explain the rise. Some of the likely causes of the gain in productivity during this period will be discussed here. An attempt will also be made to quantify the value of some of the technical innovations that have taken place. The remainder of the gain is assumed to come from non-technical sources. The nature of these sources, although largely non-quantifiable, is also discussed. Since the number of mines that have adopted the technical innovations noted here is largely unknown, the actual contribu¬tion of technological changes to the overall productivity gain can only be estimated.

Jan 1, 1990

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes&apos; new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

By Robert Schnab

ASFINAG is responsible for the construction and operation of the Austrian highway system. It is approx. 2,400 km of highways and 65 tunnels with a total length of 200 km including the Tauern Tunnel. In order to improve the documentation of the tunnel construction, ASFINAG chose to use a state of the art tunnel scanning system to record the various stages of construction: excavation, initial shotcrete lining, smoothing layer and final cast in place concrete lining. The geometric and photogrammetric documentation is provided on a daily basis to all par-ties involved. This innovative concept provides accurate & complete information in real time. The tunnel scanner documentation of the 2nd tube at the 6.4 km long Tauern Tunnel will be presented in this paper as a part of the survey contract.

By Steve Kral

U.S. mines are among the most efficient, productive and safest in the world. Much of that efficiency is due to the high-technology equipment and processes available to the industry. The U.S. mining industry can produce more material now with fewer people than it could a few decades ago. And that material can be produced more safely. However, the workforce is growing older and fewer young people are filling the holes created by retirements. Even though mining is one of the highest paid occupations in the United States, young people believe they can find jobs that pay almost as well without the risks and the often remote locations associated with mines.

Jan 1, 2002

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002