Search Documents

By Andy Thompson, Frank Perrone

"As part of the Metropolitan Transportation Authority’s $10.5bn East Side Access Project in New York, 3,200 m of tunnel had to be constructed in rock, mix face and soft ground conditions beneath one of the largest passenger railroad junctions in North America, handling over 780 trains per day. The use of risk based decision making tools was essential in developing the bespoke contract framework that was adopted as well as making informed decisions once excavation commenced. This paper will outline the risk management process adopted, discuss the risks and mitigation strategies adopted and comment on the impacts of this approach on the as built Project cost and schedule. In particular, the paper will outline the unique approach used to establish the baseline against which the Contractors performance would be measured as the selection of a Slurry TBM to excavate the tunnels was considered to compromise the effective use of a Geotechnical Baseline Report. BACKGROUND AND CHALLENGES Contract CQ031, Queens bored Tunnels and Structures was awarded in September 2009 to a joint venture of Granite Northeast/Traylor Brothers/Frontier Kemper (GTF JV) for $717.6m following a negotiated procurement process. A robust approach was taken with regard to the management and payment for risks associated with the construction of these tunnels. Risk assessments were carried out during the design phase and a risk register was developed prior to procurement. During the procurement phase close attention was paid to ensuring that the allocation and pricing of known risks, together with mechanisms for managing future risks were clearly defined between the MTA and GTF JV.In comparison to the excavation work in Manhattan, which was performed in competent hard Manhattan schist, the tunnels in Queens were excavated predominantly through soft ground with a high water table and complex environmental conditions. Not only did this require the use of pressurized face TBM technology, a first in New York, but also a re-evaluation of the contractual mechanisms used to manage the hard rock excavation contracts for their appropriateness to the soft ground tunnel work."

Jan 1, 2016

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998

Researchers at National Institute for Occupational Safety and Health (NIOSH) are investigating how fiber-reinforced shotcrete mix designs can be extrapolated from proven designs employing wire mesh. This paper explains the results of round determinate panel tests and relates the flexural strength and toughness of fiber-reinforced shotcrete to known energy absorbing properties of wire mesh. The energy absorbed with central deflection is strongly influenced by the amount of fibres. The higher the energy absorption the more load cracked shotcrete can support. Two types of fiber-reinforced shotcrete were investigated, one with steel fiber and another with polyfiber. The residual load supported in Round Determinate Panel Tests can be matched with the strength of wire mesh, thus providing equivalent bag strength values for fiber reinforced shotcrete panels. There is also evidence of a panel crack width comparison to the load holding capabilities of the fiber in the shotcrete mixes. In practice, this provides designers with a method for comparing the ground support provided by fiber-reinforced shotcrete with that supplied by wire mesh.

Jan 1, 2010

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Secondary blasting requirements have varied from one shot per 27 tonnes (30 tons) to one shot per 900 tonnes (1,000 tons) of ore. Geology, structure, cave abutment loads, and location of the ore in the column all affect the amount of oversize boulders (greater than three-fourths cubic meter or one cubic yard) that require secondary breakage. The primary method of breakage utilizes cone charges (plastic funnels filled with an emulsion) placed on accessible oversize rocks. Hangups in the brow area of the drawpoint are drilled with a self contained diesel hydraulic drill and loaded with gelatin dynamite. High hang-ups located beyond the reach of the secondary drill are "bombed" in with strategically placed emulsion bundles or ANFO bags loaded in place though a sectioned aluminum pipe.

Jan 1, 1994

By C. Clark, J. Johnson, M. Stepan

"Shotcrete and mesh are often installed to control ground deformation, falls and ejection between bolts. The combination of mesh and shotcrete forms a panel or plate that is typically bent by ground extruding between restraining rockbolts. The ground pressure applied (that is, the resistance of these panels to bending) over large ground deformations is important for maintaining ground support safety. This paper describes a new test device that measures this resistance and its evolution over large deformations. Mixes of shotcrete, mesh and other components that can maintain significant support pressure are desired, a characteristic described as the “toughness” of support. Results show toughness depends largely on how shotcrete is integrated with other components. Shotcrete strength is less important. INTRODUCTION Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often called upon to do this (Figure 1). Applications are especially common in mines with squeezing ground or seismic loading. The support pressure maintained during ground deformation is key to the performance of these systems, and to protecting miner safety. However, the toughness of a design is difficult to estimate. Researchers at the Office of Mine Safety and Health Research (OMSHR) responded to this deficiency or “gap” by designing a full scale test device, described in this paper, and beginning a testing program. Some initial results from this program are reported to demonstrate test capabilities.BACKGROUND - TOUGHNESS Mining in ground that fails from the combination of in situ and mining induced stress is commonplace. Ground support elements are installed to reinforce such ground and preserve mine safety. Typically, the strength of support is considered key, and is used to prevent or halt yielding. However, ground movements driven by creep of weak ground or seismic loading may be impossible to halt altogether. In these cases, it is essential that support is able to yield with the ground in a safe manner while maintaining confining pressure that mobilizes the strength of rock in the immediate perimeter of the opening. In addition, it’s usually desirable to contain ground between rockbolts to protect miners from loose rock that might fall or be ejected. Shotcrete and screen are often employed, sometimes together and in combination with other support elements, to accomplish this function. A key characteristic of such a system is its ability to maintain support pressure through large ground deformations, a characteristic often called “toughness” – especially in support systems incorporating shotcrete. Toughness can be quantified as the work done during deformation (e.g. force x displacement)."

Jan 1, 2015

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii's Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world's first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By Luis Fernandez-Deza, James Hawn, Dustin Mount, Jean-Marc Wehrli

The RiverRenew Tunnel System project in Alexandria, VA forms part of a CSO scheme aimed at reducing overflows of combined stormwater and sewage into the Potomac River during storm events. A major piece of the project is a 12-foot internal diameter tunnel of approximately 12,000 feet length lined with a single-pass precast concrete segmental liner and excavated by an Earth-Pressure Balanced Shield TBM. The tunnel lies between 120 to 140 feet below grade in the clays of the Upper Potomac Formation with occasional dips of more granular, saturated soils of the Terrace Formation and the Alluvium. The TBM is launched from a figure-8 configuration Pumping/Screening Shaft located within AlexRenew’s operational Water Resource Recovery Facility. This paper discusses the challenges encountered during the launch of the TBM in short mode within a highly congested site and from narrow deep shafts.

Jun 13, 2023

By V. E. Housman

EPA's Mining Waste Section within the Office of Solid Waste is continuing to collect and analyze information on mining waste management practices. Starting in 1991, the Mining Waste Section has continued to conduct site visits and prepare case study reports on the waste generation and management practices of operating mines. In choosing sites to study, a reasonable attempt was made to provide diversity in mining commodity types, geographic regions, geology, climate, and environment. To date, EPA has visited the following mines: Asarco Troy (copper) in Montana, Newmont Rain in Nevada (gold), Cyprus Thompson Creek (molybdenum) in Idaho, LTV Steel (iron) in Minnesota, Phelps Dodge Morenci (copper) in Arizona, Doe Run Fletcher (lead) in Missouri, Brewer (gold) in South Carolina, IMC Four Corners (phosphate) .in Florida, Pennzoil Culberson (sulfur) in Texas, Nerco Cripple Creek (gold) in Colorado, Copper Range White Pine (copper) in Michigan, Magma San Manuel (copper) in Arizona, Colosseum (gold) in California, and several gold placer mines in Alaska, including the Valdez Creek Mine. EPA has prepared a case study report on each facility. The mine operators were provided an opportunity to comment on their respective site visit report and their comments have been included in' each respective report. These site visit reports have in turn been incorporated into technical resource documents which provide a detailed description of each mining sector. EPA is currently reviewing the technical resource documents and plans to release the documents in the Spring of 1994.

Jan 1, 1994

By S. T. Murray

The European industrial minerals industry and its markets are largely self-sufficient. The companies who are members of the Industrial Minerals Association (IMA-Europe) number around 150 contributing 5 billion Euros to the EU?s GDP and range in size from global publicly quoted corporations to small family owned private companies. Their means and capability to implement sustainable development vary considerably. However the leading companies provide an excellent set of best practices, which IMA as a trade association with recognised core competencies in the field of sustainable development is ideally placed to promulgate throughout its membership. As an active participant in the EU Voluntary Scheme for SDI reporting IMA is not only working to increase the level of response to the SDI questionnaire but is also developing with its members a new sustainable development charter which its members will voluntarily adopt as a guiding principle for their implementation of sustainable development This work will be a consultative process involving all IMA?s section members as well as other trade associations, NGOs and MEPs. Public awareness of the benefits of minerals and their contribution to sustainable development has been raised by IMA?s awareness campaign now being followed by a more targeted programme aimed at MEPs. Further work in the future will consider product stewardship and life-cycle analysis. IMA is already positioning itself with the help of its members to assimilate the minerals industry of the accession territories in the sustainable development process.

Jan 1, 2003

By Verya Nasri, James Sullivan, Alex Varas

"INTRODUCTION Many major cities in the United States have a combined storm water and sanitary sewer network. Regular rainfall overwhelms the system capacity and results in millions of cubic meters of untreated sewage being dumped into local waterways. One legally mandated solution includes several kilometers of large diameter shallow or deep rock or soil tunnels, a pump station as well as associated collection sewers, diversion structures and drop shafts. In this paper, the basis for design of different system elements including the drop shafts and pump station is explained in detail. Common construction methods used for different type of shafts including tangential vortex and baffle plunge, and also pump station alternatives comprising cavern or various shaft configurations are discussed. DIFFERENT TYPES OF PUMP STATIONS The dewatering pump station serves as the heart of any deep CSO tunnel system and is critical to the goal of reducing CSOs by providing a controlled release of the stored tunnel volume to the wastewater treatment plant. As the major mechanical component of the project, the station will require the greatest attention by operations and maintenance staff. Designing a durable and easily operated pump station requires addressing some major challenges, including the following: • Longevity – equipment, materials of construction, and station environment • Controlling odors • Safety for operators and maintenance personnel • Easy access to equipment • Protection from hydraulic surges Location. Owners face a fundamental decision relative to the location of the pump station, which will affect how these challenges are addressed. The pump station can be built within the tunnel launch shaft or within its own dedicated shaft. This decision is driven by cost and schedule. Use of the tunnel launch shaft may provide owners cost saving opportunities by not having to construct a separate pump station shaft. However, this will likely extend the pump station construction as much as two years until the tunneling has been completed. Furthermore, delays to the tunneling operation would delay the pump station construction work, potentially leading to delay claims. For this reason, it has been more common to utilize a separate pump station shaft on recent CSO tunnel projects (Nasri et al. 2015)."

Jan 1, 2016

By D. K. Mynear, J. S. Gardner, S. Mittle, A. A. Campoli

West Virginia, although having adequate solar insolation, has witnessed very little actual solar development to date. The reasons for this lack of development are varied, but the primary obstacles to future development appear to be the absence of state-level policies and regulations promoting growth in the solar industry. West Virginia possesses large tracts of under-utilized land throughout the state created by previous mountaintop mining operations that could theoretically be re-purposed for solar farm development. Accomplishing this task will require not only revisions to the current legislation, but also acceptance by utility companies, landowners, and mining companies. Solar developers will need confidence that they can secure revenue from the electricity and Renewable Energy Certificates (RECs) generated by solar projects. Additionally, solar companies will need assurance they will be protected from any non-related environmental liabilities that could arise in the future. The primary avenue in bringing significant solar development to West Virginia will come through large corporate clients demanding or partnering with utility companies for incorporation of solar options into their energy portfolio to help meet established sustainability goals. This scenario has been witnessed in other states where a large client demands renewable options. Solar development could also represent a means through which mine operators might alleviate some of their reclamation and bonding obligations; where the landowner could supplement income from their underutilized land holdings; and where displaced miners could be repurposed in solar installation/maintenance jobs. Utilizing data from the West Virginia Permit Database, this report identifies several mine sites that hold potential for solar development in the future. INTRODUCTION The diversification of energy sources in the United States (US) has seen major shifts during the past decade resulting from: • A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques. • Incentive-driven policies leading to new development in alternative energy. • The emergence of renewable energy sources, proliferated by state and federal level incentives and falling capital costs. Coal was once the primary low-cost fuel source for the generation of electricity in the US for most of the last century, providing approximately 50 percent of the total production capacity. However, within the past decade lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and renewable sources have steadily grown to account for approximately 10 percent of the overall mix.

Jan 1, 2019

By M. Visnjic

Open Pit Mine Production scheduling under commodity price uncertainty suffers from an exponentially increasing problem size as simulations and real options flexibility are used to generate and evaluate multiple production schedules. Robustness evaluation techniques attempt to evaluate a production schedule that is generated on a single set of economic parameters against several varying prices and sources of uncertainty. This approach is invalid as the corresponding optimal LOM mine plan will change for each set of evaluation parameters. Using commodity market futures and treasury bonds as production schedule economic input parameters provides fully price and time-value-of-money risked scheduling parameters that maintain a deterministic problem size. This paper will provide comparative analysis of project NPV’s coming from traditional price uncertainty evaluation based on a single fixed LOM mine plan using varying prices versus evaluation based on varying LOM plans that are both generated and evaluated using varying prices. When cross evaluating constant price mine plans against simulations, the upside potential and downside risk of a project are significantly misrepresented. INTRODUCTION The life of mine (LOM) production scheduling problem seeks to answer the question of from where and when to extract a given block within the ultimate pit limit as well as where and when to process it. Solving this problem takes into account the constraints of extracting any particular block while seeking to maximize the net present value (NPV) of the mineral asset as a whole. A direct driver of the value of a block, and there for the entire asset, is the market price of the commodity in question. Complications arise when an optimal production schedule is attempted to be solved under price uncertainty. Many solution methodologies have been proposed in an attempt to optimize under this criterion, yet there are three salient aspects that are overlooked during this process. They are: • Generating a single production schedule and evaluating it against many simulated price paths. • Failing to understand the mechanism describing particular commodity price behavior • Inappropriate risk adjustment In an effort to address these aspects of production scheduling under commodity price uncertainty, we propose a methodology to define the economic parameters as input that is applicable to most if not all production scheduling approaches. This methodology will not only simplify the production scheduling process in terms of establishing block value but utilizes the risk adjustment of real options valuation to avoid the arbitrary blanket risk adjustment of traditional discounted cash flow valuation. Our findings conclude that attempting to optimize around individual price paths is futile and using a market risk adjusted single price forecast provides a justified economic basis for production scheduling while maintaining the same problem size as a deterministic production scheduling problem.

Jan 1, 2019

By L. R. Moore

The World Health Organization (WHO) considers contamination from oxyanions, such as selenium and arsenic, a global concern. While their elemental forms are toxic, the aqueous oxyanions are more so. These aqueous forms, which exist at a higher oxidation state, are the most common forms released during mining processes. Many technologies are capable of meeting the governmental discharge criteria for oxyanionic contaminants, but may possess limitations due to redox chemistry as well as the water matrices. An innovative technology was developed that can successfully reduce such aqueous forms generated during mining processes to a level below the discharge criteria. This paper discusses how an understanding of the sensitivities of this novel adsorbent towards these variations in water matrices and redox chemistry can be used to optimize its application.

Feb 27, 2013

By L. Yuan, J. H. Rowland, R. A. Thomas

"Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners. INTRODUCTION As many types of battery-powered mining equipment such as scoops and shield haulers are used in underground mining operations, charging stations are required to charge the equipment batteries. These batteries are of lead acid chemistry. A safety issue exists with the battery charging stations as all lead acid batteries produce flammable H2 gas during the normal charging process. Overcharging or excessive heat can quickly cause batteries to produce even more H2. If H2 is not appropriately diluted or dispersed, it builds up, and the risk of fire and explosion increases. Mine Safety and Health Administration (MSHA) regulation (30 CFR Part 75.340) requires that battery charging stations should be housed in noncombustible structures or be equipped with a fire suppression system. When a fire suppression system is used, the battery charging stations must be ventilated with intake air that is directed into a return air course or ventilated with intake air that is monitored for CO or smoke using an AMS. The monitoring of intake air ventilating battery charging stations should be done with sensors that are not affected by H2."

Jan 1, 2018

By B. Berg, J. Stephenson, J. Mansanti, C. Nyikos

"Intrepid Potash, Inc.’s Carlsbad East facility has refined sylvite and produced muriate of potash (MOP) since 1965. In addition to MOP, Intrepid Potash began recovering the mineral langbeinite from a mixed ore reserve in 2005. In 2011 a new langbeinite recovery process for the coarse (+850 micron) size fraction was constructed to enhance the overall langbeinite recovery. Based on the limited mixed ore reserve and an abundance of langbeinite ore reserves the transition of the East plant to a langbeinite only facility was targeted for 2021. Due to a decreasing grade of the mixed ore reserve, declining sales pricing, and high sylvite operating costs a strategic decision was made to accelerate this transition into 2016. To enable a successful transition, a fines recovery system needed to be developed, constructed and implemented. This paper describes the advancement of langbeinite processing at Intrepid Potash and the planning, development and successful execution of the transition to a langbeinite only operation. BACKGROUND Langbeinite (K2SO4·2MgSO4) is a double salt containing potassium sulfate (K2SO4) and magnesium sulfate (MgSO4). It is used as fertilizer and in the industry is described as Sulfate of Potash Magnesia. It is attractive as a specialty fertilizer and in addition to containing a ready source of a primary nutrient potassium, it also provides two secondary essential nutrients, magnesium and sulfur. It is especially attractive for chloride sensitive crops. Langbeinite has a specific gravity of 2.8, a Mohs hardness of 4.2, and is brittle thus very friable. It is the hardest of the saline minerals, and despite its relative softness on the Mohs scale can be very abrasive in process environments and in field applications, probably due to its conchoidal cleavage. Its solubility at 240 g/l is less than the solubility of sylvite (KCl) or halite (NaCl) and due to even slower relative dissolution kinetics washing with cold water has been a common practice for upgrading langbeinite ores. The solubilization/crystallization relationship for langbeinite is different from the majority of other evaporite minerals in that once langbeinite is solubilized it does not form langbeinite again. Instead it gives up one mole of magnesium sulfate, takes on various waters of hydration and precipitates out as either schoenite (K2SO4·MgSO4·6H2O) or leonite (K2SO4·MgSO4·4H2O) depending on temperature. Due to its partial solubility and phase transitions at its surface when exposed to moisture, there is strong cohesion between wetted particles; the resulting stickiness of the upgraded products can create significant materials handling issues unless processed in slurry form or at relatively low moisture levels. Langbeinite has been produced commercially from two locations, the Kalush and Stebnik regions in the Cartpathian Mountains of former Poland and now the Ukraine and from the Permian Basin in New Mexico (Garrett, 1996; Smith 1949). Current production is from two operators in the U.S., Mosaic and Intrepid Potash."

Jan 1, 2017