Search Documents

By Donald J. Olson, Thomas J. Lutzenberger, John Ramage

The North Shore Inline Interceptor, Phase IA tunnel is a 8,550-meter (28,000-ft) interceptor tunnel currently being constructed by Traylor Bros./Frontier-Kemper, Joint Venture, using a 9.8-meter (32-ft - 4-in) diameter Robbins tunnel boring machine (TBM). This tunnel is being driven in Silurian age dolomite approximately 91.5 m (300 ft) below ground surface. Significant water inflows were encountered when the tunnel drive penetrated the thinly-bedded Waubakee Formation. Flow increases approaching 0.75 cu m per min per 30 m of tunnel (200 gpm per 100 ft) have occurred in this formation. After driving approximately 2,285 m (7,500 ft) of tunnel (200 m full face in the Waubakee Formation), total flows exceeded 12 cu m per min (3,200 gpm) with about 5.7 cu m per min (1,500 gpm) entering the tun¬nel from the 200 m (600 ft) of exposed Waubakee Formation. Additional water control measures consisting of increased pumping capacity, increased water treatment capacity, surface grouting ahead of the tunnel, grouting ahead of the tunnel face and panning to improve the working environment for installation of tunnel support, were implemented to deal with the large water inflows. Currently (January 24, 1989), 3,400 m (11,000 ft) of tunnel has been driven, total water inflows are in the range of 11.7 cu m per min (3,100 gpm) with only 6.8 cu m per min (1,800 gpm) inflow from about 1,220 m (4,000 ft) of tunnel driven full face through the Waubakee Formation.

Jan 1, 1989

By K. K. Haramy, J. McDonnel

INTRODUCTION Primarily because of mining at greater depth, an increasing number of coal mines in the United States experience floor heave problems. In many instances, the floor heaves at a slow rate without causing health and safety related problems; only additional roadway maintenance and coal handling equipment are required. However, when rapid, massive heaving occurs, the safety of mine personnel in the vicinity is jeopardized. Extensive floor heave causes a redistribution of stress around the mine opening and can cause additional ground control problems. This paper presents an analysis of rapid floor heave in a deep western coal mine. The analysis is based on field measurements, laboratory data, and beam design theory. Factors affecting floor heave, such as mining-induced stress, mine opening size, entry orientation, mine geology, rock physical properties, and gas pressure, are considered. Examination of floor heave in the mine indicates that heaving is primarily caused by deformation of a soft floor member that is subjected to high mining-induced stress. Theoretical analysis of in situ floor stresses resulting from overburden loading indicates that floor failure will occur. The analysis is confirmed by visual observations of floor heave in the mine. Recommendations for mine layout and opening design to control rapid, massive floor heave under these conditions are also presented. MINE-FLOOR-FOUNDATION THEORY The floor stratum in a coal mine acts as a foundation to support coal pillars and artificial supports, thereby providing support to the mine roof. The overburden load, transferred through pillars and other supports, applies tremendous stress to the floor. Soil mechanics theories provide solutions for foundation design problems that apply to the mine floor. Based on foundation theory, vertical load on pillars causes high shear stress zones in the floor. If the floor is relatively weak, it may fail and dislocate upward into the mine opening. Strong roof strata that do not readily fail transmit most of the overburden load through pillars to the floor. Heaving may result, depending on the thickness and physical properties of the floor

Jan 1, 1986

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By James Warren Andrews, Philip C. Nyberg

The regulation of exposure of underground personnel to radon and its daughter products has significantly changed since the 1950's. The U.S. Bureau of Mines - Mining Enforcement and Safety Administration (MESA) - Mine Safety and Health Administration (MSHA) sequence of standards and regulations have lowered the maximum allowable occupational exposure and now the new Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants, effective in 1990, have further regulated uranium mine emissions. Under the authority of Section 112 of the Clean Air Act (42 U.S.C. 7401), the EPA has set regulations for the control of radon (Rn-222) emissions from underground uranium mines as well as other sources. Since the venting of radon from the mine atmosphere to the outside air is a major component of the miner's protection, and since this is the first quantitative effort to limit gaseous mine emissions to the environment, it was felt that it would be useful to examine the implementation of the EPA regulation at working mines. The concern was not only for determining compliance with the regulation but also for observing what effect the rule might have on mine air quality and thus on worker exposure. The regulation is stated in terms of the maximum permitted radiation dose to the closest potentially exposed individual, which is calculated from a computer program supplied by EPA and radon emission rates measured by the mine operator. Relative proximity to nearby populations determines the allowable magnitude of mine exhaust ventilation emissions. For some mines this is a serious operational constraint.

Jan 1, 1991

By Lawrence W. Teufel

Knowledge of in situ stress and natural fracture distribution at depth improves our ability to stimulate and produce low permeability reservoirs. The focus of this study is three closely spaced, 2.5 km deep vertical wells in the Piceance Basin of Colorado. The wells were completed through the tight lenticular and blanket gas sands of the Mesaverde Group. In situ stress directions and magnitudes were determined from hydraulic fracture tests and anelastic strain recovery measurements of oriented core. The distribution, orientation, and characteristics of natural fractures in the subsurface were determined from detailed observations of over 1300 m of core, of which 400 m was oriented. Stress measurements clearly show that horizontal stresses are strongly influenced by lithology. In a sandstone/shale sequence at a depth of about 2.0 km in situ stresses in sandstone formations are anisotropic, with the average ratios of the minimum and maximum horizontal stresses to the overburden stress being 0.82 and 0.96, respectively. In sharp contrast bounding shale formations are lithostatic. This stress contrast between sandstones and bounding shale formations could act as a barrier to hydraulic fracture propagation during stimulation and impede vertical fracture growth. Natural calcite-filled fractures are present in over 7 percent of the core, with several horizons having a much higher frequency of fractures. Fractures are found primarily in sandstone. The fractures have a strong preferred orientation of N 1060E[+]110, which is aligned with the maximum horizontal stress and direction of hydraulic fracture propagation. The interaction between a well developed fracture fabric and anisotropic stresses in sandstone formations produces a permeability anisotropy, with the maximum permeability aligned with the fracture fabric and maximum horizontal stress.

Jan 1, 1986

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

The US Bureau of Mines' dictionary of mining terms defines productivity as "the efficiency with which economic resources (men, material, and machines) are employed to produce goods and services." Or, the relationship between the physical outputs and the physical inputs used to produce those outputs. As demand for mine materials dropped, mining companies and equipment manufacturers discovered that ratios between the inputs and the final products were disproportionate to the profits realized. Some companies are fighting for survival. The US, while still the most productive country in the world in absolute terms, is looking over its shoulder as other industrialized nations continue to exceed its yearly productive growth rate. According to John Belcher, Jr., of the American Productivity Center in Houston, TX, the US has seen a steady decrease in productivity growth since the mid-1960s. During the post World War II period, the US labor productivity growth rate was 3.2% annually. The slowdown began in 1965 and by the mid-1970s, the country's annual growth rate was 1%. By 1978, labor productivity growth ceased to gain at all and from 1978 to 1980 a 2% decline occurred. Solutions to the productivity decrease are increasing product prices or improving productivity. By increasing prices, though, the producer runs the risk of pricing himself out of the competitive market. To maintain an acceptable profit level, prices must increase proportionately higher than required to offset production cost increases, Belcher says. Many companies are turning to in-house productivity improvement programs as an answer to increased costs and declining profits. These programs are geared toward management commitment and employee awareness of what productivity means. Companies are finding ways of measuring productivity levels in financial reporting, budgeting, and planning. Organizational teams have been formed to coordinate activities and oversee product management, and improve productivity of materials and capital investments. This special issue of Mining Engineering examines productivity in the mining industry. First, there are articles about various, and different, factors that affect productivity in each of ME's five main readership areas - exploration, mining, processing, coal, and industrial minerals. There is also a look at mining industry productivity from the manufacturer's view. The next section of this special issue is devoted to some topics that affect all areas and sectors of mining: research, management practices, computers, maintenance, and energy management. Then follows case studies in exploration, coal, and iron and steel. These studies provide examples of practices and strategies used by companies and operations to boost productivity.

Jan 11, 1983

In 1991, most industrialized countries, except for Germany, were in a recession or a period of reduced growth. The US economy, already in recession, suffered from mounting banking system losses and the uncertainty brought about by the Persian Gulf War. However, US and worldwide minerals exploration did not collapse as it did during the mid-1980s. Even though gold and base metal prices declined, prices were still above cash costs for most operations. This allowed the continuation of established exploration programs but sharply limited new initiatives. Exploration 1990-1991 Planned worldwide 1991 exploration expenditures declined by about 8% from 1990 levels, according to a survey of 153 companies by the Metals Economic Group (MEG). Canada was the leading exploration target with 23% of the total, followed by Australia and the US (19% each), South Africa (13%), Latin America (11%) and the South Pacific (7%). The remaining 8% was split evenly between Europe and the rest of Africa. In Latin America, Mexico and Chile are the most attractive countries for exploration. Recognizing the risks involved, the industry has been cautious about ventures in the former Soviet Union. Survey results also showed that while the majors expected to maintain exploration spending, smaller firms were cutting back or actively seeking farm-outs from the majors (personal communication, M. Wegener, MEG).

Jan 1, 1992

By M. J. Garcia, Howard Hallman, G. M. T. Marshall, Ken Higby, Louis Cope, Robert S. Hess, John Peters, A. G. Law, William C. Larson

After a good year in 1979-strong mineral demand, adequate prices for most metals, minimal labor problems-1980 was not so good. The US produced $24.8 billion worth of nonfuel minerals last year, up 3.5% from 1979, according to preliminary US Bureau of Mines figures. But the $800 million increase was the smallest annual gain since 1977 and reflected reduced auto and construction industry demand, strikes, and energy shortages. Preliminary figures for 68 minerals show that production of 42 decreased, 25 increased, and one was unchanged. Production of 11 of 21 US-produced minerals was up. Noteworthy mineral events in 1980 included a copper industry strike, increased gold and silver prices, troubles in the iron ore and uranium industries, discussion about a US nonfuels mineral policy, and corporate interest in mining companies as merger targets. Recessionary conditions experienced by the Western world in 1980 resulted in a slowdown in new mine development, evident in the relative scarcity of major new base metal projects. This could lead to short term supply/demand anomalies within the next few years which, in turn, could have a significant effect on metal prices, according to Mining Magazine (Jan. 1981). World Mining (Sept. 1980) noted that US mining strength is in open pit operations. A much lower tonnage is mined underground and is centralized in trona, uranium, lead, zinc, molybdenum, potash and, to a lesser extent, copper. The most notable increase in new underground mines has been in Wyoming's trona district where new mines are being developed and production will increase, the magazine said.

Jan 5, 1981

By Sharon Thomson

Since 1977, Amax Coal Co.'s Belle Ayr mine near Gillette, WY, has been the largest producing coal mine in the US. In its 10 years of operation more than 90 Mt (100 million st) of coal have been shipped from the mine's facilities to electric generating plants across the country. It is thought to be the largest amount ever produced in US history from a single coal mine. The railroad is Belle Ayr's lifeline for moving this massive volume from a relatively isolated corner of northeastern Wyoming. There are no waterways for barge traffic, and highway truck hauling would be impractical considering the quantity and distance of coal to be moved. Transportation in the Powder River Basin-at least for the present-is strictly unit trains. An average of four unit trains daily load at Belle Ayr. These trains average 108 cars long, with a capacity of 91 t (100 st) per car. Burlington Northern Railroad serves the Powder River Basin, but locomotives supplied by Union Pacific, Milwaukee Road, and Kansas City Southern are a common site as well, since coal will often travel these lines too on its way to utility plants in Colorado, Kansas, Iowa, Texas, Arkansas, Louisiana, Wisconsin, and Oregon. When Belle Ayr opened transportation in the Powder River Basin was in an early development stage. As the first large-scale coal shipper in the area, Belle Ayr was the only user of a 27-km (17-mile) railroad spur south of Gillette. Other mines, however, were to open soon on the abundant, low-sulfur reserves. Today, less than a decade after Belle Ayr's debut, 13 large-capacity mines operate near Gillette. The 27-km (17-mile) spur that once served only Belle Ayr has been extended 177 km (110 miles) south to service other mines as well, and to tie into a major rail line in central Wyoming. The Powder River Basin is now served by a wishbone-shaped track configuration that allows train movement north into Montana, south into Colorado, and east into Nebraska for connections across the country. Operations at Belle Ayr are closely tied to train arrivals and departures, with coordination essential between mine operations and rail personnel. "Train movement in the Powder River Basin has evolved to the point where we are fine-tuning mining operations to coordinate them with a more dependable transportation system," according to Joe Jefferson, transportation supervisor with Amax Coal's western division. That, however, hasn't always

Jan 10, 1982

By Donald A. Dahlstrom, Wai-Ping Kam

The mineral industry and individual processing plants are large consumers of energy. While energy conservation has received some attention in the present Federal Administration National Energy Strategy proposal it is obvious that the mineral industry should also continue to emphasize energy consumption reduction for important economic savings alone. As indicated by other studies, comminution is the largest single consumer of energy in the mineral processing plant (1.3% of total electrical energy consumption in the U.S.A.).1 Fine grinding is the largest portion of this amazing statistic. While substantial energy savings have been demonstrated by new machine developments and improved control methods, undoubtedly there are additional areas in comminution where substantial progress can be made. Some time ago, the U.S. Department of Energy published a report on "Comminution and Energy Consumption" by a committee composed of experts in the field of comminution from industry and academia. They identified the following potential for energy savings by specific areas? Classification device design 9-13% Comminution device design 3-16% Control 9% Grinding additive 3-6% Materials 3% It is apparent that the classification device had the first or second highest savings potential. Obviously, serious research consideration must be given to this technology area. A series of three papers have previously been written on the subject of two stage classification research work for ball mill operation by the authors. Accordingly, a brief review will be made. Previous Research Results on Two Stage Classification The hydrocyclone was selected as the type of classification equipment for this study as it represents by far the majority of the devices used in ball milling. While four different hydrocyclone circuits have been proposed by others,3 only two were considered in this work as illustrated in Figure 1. Flowsheet A is truly counter-current in nature in that the product from the ball milling circuit is taken from the first stage overflow

Jan 1, 1992

By V. C. Rogers, K. K. Nielson

INTRODUCTION An evaluation of the radiological health risks from uranium mining and milling requires the determination of several key parameters. As shown in Figure 1, the first step is the estimation of the radioactive source term. The radionuclides in the ore consist of the 238U decay series nuclides shown in Figure 2, the 235U series nuclides, and 40K. The 238U decay series isotopes dominate the source term, with the 235U series isotopes causing less concern and 40K remaining at background levels. [ ] Specifically, the risks from uranium mining and milling are mainly associated with 230Th, 226Ra, 222Rn, and its short-lived daughters. These radioisotopes are mainly alpha-particle emitters; hence, some dispersion mechanism is necessary to bring them into intimate contact with man so that they can be inhaled or ingested For water pathways, the leaching of the isotopes from [ ] the solid ore or tailings provides a measure of the amount of contaminant initially available to the environment. For the air pathway, dust-creation mechanisms such as blasting, crushing or general resuspension processes dominate for 226Ra and 230Th. However, 222Rn, being a chemically inert gas generated from the decay of 226Ra, can migrate through the ore, overburden and tailings over considerable distances. As shown in Figure 1, the next step in the pathway to man is environmental dilution and delay. For the water transport mechanism, the delay in the isotopes reaching an accessible water supply may be considerable (several thousand years or more), but for airborne nuclides the dispersion in the atmosphere is rapid and constitutes the main mitigating factor. Considerable ventilation is provided in underground mines to dilute and remove radon and its daughters in order to keep their concentrations low and thereby minimize their inhalation by miners. The rate of uptake by both the workers and the general public is often difficult to ascertain. It involves breathing rates, rates of water consumption and other poorly-defined parameters. The final steps are the risk estimators used to predict doses and cancer rates from the inhaled radon daughters and ingested or inhaled radium. Many

Jan 1, 1981

By K. N. Santini

The evaporite deposit at Searles Lake consists of alternating brine-saturated saline beds and saline-bearing mud beds. Three major subsurface brine-saturated saline horizons have been identified by private companies and the U.S. Geological Survey. They have been termed, from bottom to top, the Mixed Layer, Lower Salt, and Upper Salt. The important water-soluble components (Na, K, Mg, CO3, HCO3 , SO4, Cl, and B407) are either in brines or have combined to form the following minerals: halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, northupite, sulfohalite, glaserite, etc. Kerr-McGee Chemical Corp., the current operator at the lake, selectively pumps interstitial brines from each of the major horizons to feed its three chemical plants. As the pumping continues, brines are continuously replenished within the deposit by dissolution of the minerals through natural recharge or artificial fluid injection (solution mining). The brines are processed to produce a variety of chemical products, which include sodium carbonate and sulfate, potassium chloride and sulfate, sodium borate, and boric acid. The Anaconda Minerals Co. has been evalua¬ting potential domestic trona acquisition since 1981. We have evaluated various properties in the Green River, Wyoming trona district, and Owens Lake and Searles Lake in southern California. In 1983, we purchased with our joint-venture partner, Leslie Salt Co., the southern portion of Searles Lake from Occidental Petroleum Corp. Since mid-1983, Anaconda has been conduct¬ing a small exploration-drilling program at the property. The initial core holes were drilled along and adjacent to the existing access road. In 1984 we used an all-terrain drill rig to gain access to drill sites on the playa where no roads exist. The use of this equipment proved to be highly successful. The drill program consists of coring to an average depth of 450 feet and collecting brine samples from potentially commercial horizons. The brine samples are collected by setting a packer and swabbing the hole. The core is logged and split lengthwise; one-half is submitted to our Tucson Geoanalytical Laboratory for semi-quantitative mineralogy by X-ray diffraction and the following suite of chemical analyses: Na, K, Mg, C03, HCO3, SO4, Cl, B407, Li, H20 insolubles, and acid insolubles. Additional test work for selected core samples will include effective porosity and horizontal permeability determinations. The brine samples are subjected to the same suite of chemical analyses (minus insolubles) as the core samples. In addition, specific gravity is also determined. Both cross sections and isopach maps are being constructed. The hydrological characteristics of the potentially commercial horizons are also being investigated.

Jan 1, 1987

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993

By Kaye P. Strong, Desmond M. Levins, Anthony G. Fane

1. INTRODUCTION The safe disposal of tailings is the most important environmental question facing the uranium mining industry today. This is because tailings present a major long term radiological hazard as they contain about 71% of the radioactivity originally in the ore. The magnitude of the problem can be appreciated by considering the quantity of tailings involved. For example, projections of milling programs in Australia indicate that there will be 100 million tonnes of tailings produced by the year 2000 (Levins 1980). The United States currently has in excess of 100 million tonnes and by the year 2000 will have between 900 and 1700 million tonnes (Landa 1980). Present options for tailings rehabilitation include leaving them above ground, returning them to the mine or placing them in specially excavated pits. In any event, the tailings will be covered with earth and revegetation attempted. This will remove the problems of airborne radioactive dust and water erosion of the tailings, at least in the short term, but diffusion of radon-222* from the tailings may still occur. The Atomic Energy Control Board of Canada (1981) has proposed a maximum allowable radon flux from rehabilitated tailings of 0.074-0.37 Bq m -2s-1(2-10 pCi M-2 s-1); the exact level is to be determined "after discussion with other regulatory agencies and the industry". The United States Nuclear Regulatory Commission (USNRC 1980) has been more restrictive in recommending a maximum flux of 0.074 Bq m -2s-1 (2 pCi m-2s-1). As a guideline they also suggested a minimum depth of covering material of 3 m to achieve this surface flux for tailings typically found in the western milling regions of the United States. The design of rehabilitation schemes is aided by a knowledge of radon transport through tailings piles. In this paper we present the results of a theoretical analysis and experimental study of radon diffusion through selected Australian tailings and cover material. The minimum cover criteria of 3 m is reexamined in the light of these findings. [ ]

Jan 1, 1981

By R. C. Dunne, C. T. O'Connor

Flotation practice on eighteen South African flotation plants is described. The plants are categorized as those treating reclaimed tailings, those treating material which has already been subjected to cyanidation or uranium leaching, and those treating milled ore. The similarities and differences are highlighted.

Jan 1, 1998

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By R. E. Muller, L. G. Martin, J. M. Stonehouse

Erratic distribution of values in free gold ore bodies presents severe problems in sorting material in large scale open pit mining. However, an intense program of modern blasting techniques and less than modern gold panning results in good sorting at Houston International's Manhattan mine. Blasting technique is important. If the sample location cannot be relocated because of blasted material movement, information acquired while drilling is useless. So short benches are critical to minimize dilution. Though not very accurate, panning allows for rapid analysis. The more accurate fire assay does not provide the needed speed. Panning can be fairly accurate and errors made are mostly on the low side. Samples of mixed and broken stockpile material are used as checks on pit procedure and to develop stockpile content in¬formation. Added tonnages discovered offset the higher labor costs of this careful sorting technique. The mine is located in central Nevada's Toquima Range in the small mining town of Manhattan, 322 km north of Las Vegas. The mine has four epithermal stockwork ore bodies that are mined in two pits. The mine problem was that conventional ore control was not separating ore from waste. Assays of 6-m blast-holes were used on 5-m centers. The blastholes were relocated by stadia survey after blasting. Holes assaying above the cutoff grade were flagged and mined as ore. This system is practical and useful in high concentration ore bodies or in evenly disseminated mineralization. But it was not practical at Manhattan because of large gold particles and small ore pocket sizes. Ore pockets were often missed when drilling a grid area for blasting. Also, large gold nuggets made assay results unreliable. The probability of a nugget being contained in an assay charge is small. So most results were low, compared to actual grades mined based on stockpile samples. When a nugget found its way into a fire assay charge, the result would be far higher than the actual grade of material represented. In addition, disturbance by blasting created problems in relocating ore. Because of these problems, the grade control program was intensified in September 1979. It successfully separated ore and waste in blocked out ore areas and located more ore in "waste" areas. Known reserves mined to date have increased up to 50% on some benches. The methods used are modern blasting techniques, detailed assaying, and traditional panning of samples collected from active mining faces. These methods allow mining flexibility, to match the variable mineral occurrence in ore bodies. The united effort of the geology and engineering departments has been important to the program's success.

Jan 12, 1980

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002