Search Documents

By M. J. Liesveld, D. Liesveld

For a Colorado mountain quarry, the Water Jet Channeling Method is far superior to Burning, Sawing, Drilling, or Shooting with Primer Cord, Water, or Black Powder. Throughout the life of our quarry, which was founded in 1947, we have used all the methods and turned to the Water Jet Channeler, which we invented and patented as our ideal way to remove dimension granite from our quarry. We jet the block on 4 sides and remove the block with plugs and feathers on the backside. The Water Jet uses approx 7.5 l/m (2 gpm) running at310,000 kPa (45,000 psi) to erode the crystals @ 1sm/h (10sf/h).The 0.533mm (.021”) nozzle oscillates back and forth to achieve an approx 5cm (2”) channel. Using the Jet, we do not lose corners or cause cracks in our red fine grain light class 5 granite.

Jan 1, 2004

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

In May 1993, SME contracted with The Dolecek Companies of Denver, CO to conduct a salary survey and a study of Mining Engineering. A written, four-page survey was sent to a random select sample of 1897 current SME members from the United States and Puerto Rico and to 40 current SME members from Canada. A total of 621 survey responses were input and analyzed, to guarantee the validity of the survey findings. The findings are representative of the entire SME membership. And the survey is within a statistical range of accuracy of plus or minus 5%. Salary survey SME members currently earn an average of approximately $60,000 a year. Some 45% earn less than $60,000 and 49% earn more than that. About 24% of all SME members earn $80,000 or more each year and 13% earn $100,000 or more. Not surprisingly, a statistically greater number of owners (27.5%) and those in senior management (30%) have a current income or salary of $100,000+ a year.

Jan 1, 1993

By S. R. S. Sastri, G. V. Rao

Because the nickel contained in lateritic nickel ores does not occur in an identifiable mineral, it is generally accepted that these ores are not amenable to beneficiation. For this reason, such ores are either directly smelted or leached to extract the nickel. In this paper, a process for enriching the nickel content of the lateritic nickel-bearing chromite overburden, normally a waste material generated during chromite mining, is described. In this flotation process, a nickel preconcentrate containing >1.1% Ni was obtained from material containing as little as 0.36% nickel. An empirical relationship was developed to predict the grade of nickel that can be obtained.

Jan 1, 1997

By H. M. Breza

Recovery of phosphate concentrate at Texasgulf’s Aurora Mine has received increased attention as existing mine and plant production capacity limits are reached. Improved mining techniques and mineral processing of waste streams offer the potential to increase phosphate production without major expansion. Innovative processes are being identified to maximize pit mining recovery and to minimize waste stream losses. This results in more effective use of the phosphate. Texasgulf Inc., is a wholly owned subsidiary of Elf Aquitaine. The Aurora phosphate rock mine and refining facilities are located in North Carolina on the south shore of the Pamlico Sound. Phosphate ore is recovered by open- cast mining techniques. Draglines and other earthmoving equipment are used to uncover and mine the phosphate ore. The mined ore then is slurried and pumped about 8 km (5 miles) to the processing plant.

Jan 1, 1994

By R. Church

The southern Powder River Basin (PRB) of Wyoming has developed into the largest coal producing region in the United States in the relatively short time span of 22 years. Since the opening of the first non-captive mine in the Basin in October 1972, truck/shovel fleets have played a major part in this rapid growth. In 1994, more than 200 trucks and 50 shovels will be used at 14 mines to help produce more than 190 Mt (210 million st) of coal in the southern PRB. This article presents an overview of the truck/ shovel operations in the Basin. Fleet sizes are reviewed, applications discussed, operating considerations explored, factors looked at that drive high capacity and restrictions listed for future growth. Fleet size Various sizes of trucks and shovels can be found in the southern PRB. However, a clear trend of increasingly larger size units is being established as producers attempt to remain competitive and productive.

Jan 1, 1994

By D. D. Harbuck

Previous studies at the US Bureau of Mines (USBM) have shown that only 70% to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the USBM developed and researched the hypothesis that minor amounts of germanium and zinc silicate, present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of formed silica gel increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1994

By Owen Kreilis

By the time coal was discovered in Newcastle, Australia in 1791, it was already a most important industrial commodity in European countries. Coal was the first mineral to be discovered in Australia and the first to be mined. Today, coal remains Australia's most important mineral in terms of local use and international trade. The first mechanized longwall in Australia began operation in 1963. It contained self-advancing hydraulic supports and was installed at Coalcliff Colliery, located in the Southern Coalfields of New South Wales. After nine months and production of 53 kt (58,000 st), the unit was withdrawn, largely because of uncontrollable roof weight and with the problems of airborne dust and large coal still unsolved. Basically, roof support was insufficient. The European design of the Coalcliff longwall was inadequate for Australian conditions. Another type of support with modifications was installed and began operation at Kemira Colliery at Wollongong, New South Wales, in 1964.

Jan 1, 1995

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By R. Hogg

The various sub-processes which, together, make up the unit operation of froth flotation all depend on the characteristics of the feed solids, the solution phase, the air bubbles and the mechanical/hydrodynamic action of the machine. Characterization is obviously necessary for evaluation and process control, but the relationships between characteristics and process response are often unclear. A model-based characterization scheme is proposed in which material and system characteristics are evaluated in the context of simplified models for the individual subprocesses. The general basis for such an approach is discussed using the process of particle attachment and the influence of mineral liberation as examples.

Jan 1, 1989

By J. C. Norman

The United States was the world's largest producer and consumer of boron compounds during 1994. According to US Bureau of Mines (USBM) estimates, boron mineral concentrate and chemical production in the United States totaled about 1.05 Mt (1.15 million st), yielding 560 kt (617,000 st) of B203, for a total estimated value of $370 million. This production level was about 2% less than 1993 revised figures. The United States continued to provide nearly all of its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid for export. Domestic employment in the mining and beneficiation of boron products during 1994 was 900 people, about the same as in 1993. USBM estimated total world production of boron of about 2.3 Mt (2.5 million st), yielding 1.1 Mt (1.2 million st) of B203. World production during 1994 was about the same as during 1993. USBM estimates US reserves to be about 210 Mt (231 million st) of ore and world reserves to be about 630 Mt (694 million st) of ore.

Jan 1, 1995

By R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1997

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By John A. Shuster, Joseph A. Sopko

Construction of two shafts, as well as associated deep concrete structures, for a major storm sewer project in Milwaukee, Wisconsin required ground water control and temporary ground support to depths ranging from 19.2m to 55.0m. Lowering of the site ground water table eras not possible because of potential consequences for existing nearby structures. Construction entailed completion of two shaft collars into bedrock. In addition to the shafts, several adjacent connected. structures were completed. Ground freezing was selected to provide temporary ground support and ground water control for all excavations. The first application of using reinforced frozen earth was successfully incorporated on the project. The procedure enabled the contractor to create openings in excess of 9.1m in height, without bracing, through highly stressed frozen earth walls. Design features and construction procedures for completion of ground freezing and related excavation are reported.

Jan 1, 1989

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on cab air filtration system performance. Factors experimentally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab protection performance. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Gary A. Almeraris, Thomas F. Peyton

This paper describes the innovative procedures employed during the construction of 3 deep shafts within the confines of New York City. The shafts, which varied in diameter from 1.8m (6ft) to 7.3m (24ft) and had an overall depth of 199m (650ft), were excavated by both mechanical and conventional methods. These were subsequently concrete lined, clad steel riser pipes installed and associated surface structures were constructed. Tricky surface rock blasting coupled with the unearthing of unexpected obstructions caused constant uncertainty during the excavation phase. In addition, the necessity of handling men and material in restricted yet deep openings required the development of a safer and more productive shaft construction procedure.

Jan 1, 1989

By T. A. Toney, L. R. Fish, P. J. Bethell

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers and recirculation have been attempted with some success. This paper reports on a novel (patent applied for) approach to retreating spiral middlings in a heavymedia cyclone circuit.

Jan 1, 2000

By Jack G. Pippenger

The Coteau Properties Co.'s Freedom Mine is a surface lignite mine that uses large draglines, trucks and shovels, tractor-scrapers and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity and distance. The system was also used to provide historical information to plan the most efficient and economic use of each equipment type in the mining operation. The Coteau Properties Co. is a wholly owned subsidiary of The North American Coal Corp. The company was formed in 1972 to supply lignite from its Beulah-Hazen coal reserve to a coal gasification project and an electrical generating facility located near Beulah, ND. The reserve consists of a single coal seam between 3 and 7 m (10 to 23 ft) thick. The overburden above the coal is predominately glacial tills and clays and ranges from 6 m (20 ft) to more than 60 m (200 ft) thick.

Jan 1, 1994