Search Documents

By John G. Viets, J. Robert Clark

A multielement extraction system is being used successfully to provide essentially interference-free geochemical analyses to aid in gold exploration. The Methyl isobutyl ketone-Amine synerGistic Iodide Complex (MAGIC) extraction system separates Ag, As, Au, Bi, Cd, Cu, Ga, Hg, In, Mo, Pb, Pd, Pt, Sb, Se, Sn, Te, T1, and Zn from interfering geological matrices. Quantitative extraction of these elements is accomplished over a broad range of acid normality, making it possible to economically determine all 19 elements from a single digestion or leach solution. The resulting organic extracts are amenable to analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES) and flame atomic absorption spectroscopy (FAAS). For many years the principal shortcoming of ICP-AES was the complex spectral and stray-light interferences that were caused by the extreme variability of components such as Fe. Na, and Ca in common geological matrices. The MAGIC extraction allows determination of the extracted elements with enhanced sensitivity, from a virtually uniform matrix, by ICP-AES and FAAS. Because of its simultaneous multichannel capabilities, ICP-AES is the ideal instrumental technique for determining these 19 extracted elements. Ultratrace (sub-part-per-billion) determinations of Au and many of the other extracted elements can be made by graphite furnace atomic absorption spectroscopy (GFAAS), following back stripping of the extracts. The combination of the extraction followed by stripping of the organic phase eliminates 99.999% of potential interferences for Au. Gold determination by GFAAS from these extracts under the specified conditions yields a fourfold improvement in sensitivity over conventional GFAAS methods. This sensitivity enhancement and the interference-free matrix allow highly reliable determinations well into the parts-per-trillion range.

Jan 1, 1990

By H. Polat, B. Mohal, S. Chander

Several nonionic surfactants and one anionic surfactant were tested to enhance the flotation response of a low-rank coal. The nonionic surfactants included an ethoxylated octylphenol and several polypropylene-polyethylene block copolymers, and the anionic surfactant was a dioctyl sulfosuccinate. All of the surfactants improved the yield significantly, but the influence on grade was complex. To elucidate the mechanisms involved, separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents, a correlation between the emulsifying power of the surfactant and the flotation response was observed. An increase in the number of droplets produced was considered to he the main reason for increases in the yield. However, a small amount of surfactant adsorption on coal is essential to promote adhesion of oil droplets. When the surfactant was introduced into the flotation pulp prior to addition of dodecane, the benefits of the surfactant decreased significantly. The decrease was attributed to both a decrease in hydrophobicity of coal through increased surfactant adsorption and a decrease in the surfactant available for emulsification. When a surfactant dispersed in oil was used, the transfer of surfactant to the aqueous phase was minimal, and a considerable increase in yield was observed.

Jan 1, 1995

By F. Aurelian

The development of the uranium mining industry in Romania started in 1950. The exploitation of Bihor region, one of the most important metallogenic zones of the country, began in 1962. Uranium exploitation activities were ceased in 1995 due to the exhaustion of the ore deposits. Between 2001 and 2002, due to the entire mining zone closure, ecological rehabilitation and decommissioning was initiated. The proposed solutions, concerning terrain, equipment and buildings utilization were elaborated according to the guidelines of the Romanian Environmental and Nuclear Authority.

Jan 1, 2006

By L. Lacerda

Shotcrete is widely accepted as an indispensable form of ground control around the world. Other Surface Support Liners such as mesh have been around as long as shotcrete while other Thin Support Liners (TSLs) have been introduced in recent decades. TSLs, however, have yet to replace shotcrete in many applications believed to be “perfect” for them. On the other hand, some recently introduced technologies may be on the brink of meeting most surface rock support requirements economically and safely. This paper will discuss rockfall statistics, small rockfall prevention and compare different surface support liners such as mesh, shotcrete and TSLs. Additionally, a shaft sinking TSL application example will be presented.

Jan 1, 2004

By Alan Bye

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimise the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focussed on ore characterisation and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blastability indices as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model however it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables as well as higher plant throughput. Additionally, the initiative has benefited both Brownfield and Greenfield projects on the PPRust operation.

Jan 1, 2005

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Richard R. Klimpel

INTRODUCTION The purpose of this paper is to summarize the current status of reagents used in the mineral industry plus present some current challenges and possible new technologies of the future. Table 1 lists the important families of reagents which, when taken together, constitute at least 95% of the current commercial reagent market. A very approximate estimate of the free world reagent market size in mineral applications is about 1.5 to 2.0 billion dollars (U.S.) using 1985 data. Obviously, to serve such a large market requires the effort of many different types of commercial supply sources. It is estimated that there are over 300 industrial firms in the free world that have a dedicated business/technical structure for supplying reagents related to the mining industry. There are a number of characteristics which are associated with the product families listed in Table 1. Understanding these characteristics helps to provide a realistic economic/technical basis for outlining future challenges in mining chemicals. 1.Essentially all of the products listed are old chemistry in the sense that the molecules have been known and manufactured for at least 25 years. This has not been a highly dynamic field of endeavor from the viewpoint of new product introduction. 2. The greater majority of the products listed can be viewed in commercial terms as "commodity" chemicals, that is, they are available from many sources and the pricing of a some- what generic product generally dominates differences in product quality or uniqueness. With commodity pricing, reagent suppliers significantly reduce research expenditures, loosen product quality somewhat if the applications of the reagents allow, etc. in order to be cost competitive.

Jan 1, 1989

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. A preliminary indication of the repeatability of a simplified alternative method (MN DNR method) was assessed and results from the MN DNR method were compared to those from the ASTM method. To provide an indication of repeatability, six samples from three different rock types were subjected to dissolution testing for periods of 20 to 68 weeks. Drainage pH values at the end of the tests were within 0.5 units in all cases and within 0.05 units in four cases. The percent difference from the mean for overall sulfate rates from paired cells ranged from 0.04 to 1756, with a median of 6.3%. Nine samples from four rock types were subjected to both MN DNR and ASTM tests for periods of 20 to 132 weeks. The difference in final drainage pH values forsix of the samples was less than 0.1 unit, and these values were less than pH 3.65 or greater than pH 8.0. The final drainage pH difference for the last three samples ranged from 0.15 to 0.4, and these values were ill the pH range of 6.2 to 7.2. The sulfate release rates for the periods of record for the MN DNR method were 70 to 150% of those for the ASTM method, with a median value of 110%. Sulfate and calcium release from the two methods was not substantially different. The MN DNR method typically produced higher magnesium release.

Jan 1, 2000

By Morris Loshinsky, George Ziegler

The New York City Transit System is celebrating its Diamond Jubilee this year. In 1904, 9.3 route miles of New York's first subway was placed in operation in lower Manhattan. Since that date the system has grown to 230 route miles and 458 stations (See Exhibit #1). The age of the system immediately provides a clue to the nature of our construction activity. While we must always plan for the future and expand the system in the direction of the future needs in New York, a substantial amount of time and money must be channeled towards the modernization and maintenance of the existing system which provides vital transportation for 3-1/2 million passengers a day. This paper however will be directed to our New Route's Construction and, specifically, to three rock tunnel and cut and cover sections presently under construction. Currently, New York is engaged in the construction of about 9 New Route miles of structure. Briefly, the 3 Sections we will discuss are as follows: Route 131-A Section 5A is a 4 track structure in Manhattan and includes the new Lexington Avenue Station. This 1240 foot long section is located between Park Avenue and 3rd Avenue and is a combined cut and cover and rock tunnel section under 63rd Street. Route 131-A Section 5B is an intricate 2423 foot long 4 track rock tunnel section extending from 3rd Avenue to the FDR Drive under 63rd Street in Manhattan.

Jan 1, 1979

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By J. P. Mogan

As diesel exhaust contains a mixture of several materials of varying degrees of toxicity which interact to a currently undefined extent in their effects on health, the prescription of a quantity of ventilating air to dilute the exhaust to a safe level is necessarily, to some extent, arbitrary. Some jurisdictions rely on the application of a safety factor to a single "governing" component (usually nitric oxide for most modern diesel engines). Others specify that the total of the "adjusted" concentrations (actual concentration divided by maximum permissible concentration) not exceed "one" for related constituents (irritant gases for example). Neither of these approaches, however, takes account of the interaction of the gaseous constituents with diesel soot (although many studies verify such interactions), nor do they provide any economic incentive for reducing pollutants which are not included in the criteria for ventilation. Because of these factors, the Canadian Department of Energy, Mines and Resources awarded a contract for a study of the current literature bearing on the "Health Implications of Exposure of Underground Mine Workers to Diesel Exhaust Emissions" (1). One goal of this study was the formulation of a new ventilation criterion. The contractors, Ian W. French and Associates, studied more than 1500 literature citations which they interpreted in a 350 page report and summarized in a companion 1600 page annotated bibliography. In the recommendations section of the report, they defined a new 'health effects index' or ventilation criterion "V" as follows: [ ] The contractors consider that a "V" between 3.0 and 4.0 poses a moderate threat to health which could be alleviated by the use of protective equipment such-as filter helmets. If V exceeds 4.0, an increase in ventilation quantity to reduce the pollutant levels is indicated. In the case of mines with a quartz content in excess of 20% in the ore, the contractor recommends that a term. [Quartz]/ [Threshold Limit Value Quartz] be added to the equation, and [2.0 = ?v? = 30] be the range justifying protective equipment, with added ventilation if "v" exceeds 3. A degree of pragmatism was inherent in the development of the equation, as the contractors recognized that the components of the index, if it is to be useful in the near term, should be within current routine underground environmental assay capability.

Jan 1, 1980

By M. S. Kabibwa, E. K. C. Chanda

In planning for the future, Nkana Division deepened the Mindola sub-vertical shaft which was commissioned in 1994 in order to access the 30 Mt of ore between 1274 and 1570 m levels. The Nkana Synclinorium which is estimated to contain 250 Mt of ore is being accessed from the vicinity of Central Shaft. These areas are being planned with the intention of maximizing the use of computers in geological modelling and mine design so as to overcome the inadequacies of manual planning techniques. As a result, there is an increased demand for quality output from the computerized mine planning system the division has been developing over the last few years. A new workstation comprising the Hewlett Packard HP 71 51100 MHz and a CRX graphics monitor was acquired in 1995 together with the LYNX (version 3.09 and version 4.0) Mine Modelling System. Currently the workstation is being used for geological modelling and mine design for the Zerofold at Central Shaft and the Mindola mining at depth project. AutoCAD and Mine Works Planner have been added to the sys- tem configuration. Mine Works Planner is likely to replace Lo- tus123 for mine scheduling tasks. Computer applications in the area of mine planning at Nkana has led to considerable time savings and improved efficiency in areas formerly performed manually and has allowed speedy processing of data that would otherwise have proved too time consuming. Nevertheless, a lot of work still needs to be done in the areas of geostatistics, stope design and financial modelling of mining options. For the foreseeable future computer based planning will operate parallel to manual methods until such a time as sufficient personnel are proficient in the use of computer systems. This paper describes the program of computerization at Nkana Division, reviews current applications and the benefits and experience gained and discusses the promise of current and future developments.

Jan 1, 1996

By R. L. Loofbourow

In addition, dewatering is seldom complete because of aquifer irregularities and an operator's natural reluctance to start a costly study program, provision of wells, and pumping long before mining begins. In some cases, water pumped from the mine is used in treatment. This use is suggested as a way to minimize effluent effects. The true objective of water supply, however, is to provide water of satisfactory quality at the rate needed and at the least cost. Pumping to permit efficient mining isn't likely to coincide strictly with that objective during much of the mine life. The history of mining is replete with efforts, some highly ingenious, to control mine water. Methods that might be used to tackle the challenge Operators of wet mines are faced with both obvious pumping costs and some unquantified water costs. It is possible to reduce both types of costs, generally by reducing inflow to the mine area-and a surprising number of methods have been used to do this. Both the obvious and unquantified costs at a wet mine are now multiplied by: •Increasing costs of power, labor, equipment, and supplies; •Work at greater depth and, in some cases, in wetter ground; •Increasing use of hydraulic fill; and •Increasing zeal in protection of surface and groundwater quality. There are many easily overlooked ways in which mine water may add to hazards and costs (Loofbourow, 1973). As to their importance, consider these examples: •Increased maintenance of equipment, tires, roads, and ditches; •Increased difficulty in supplying proper ventilation; •Increased hazards from ice and use of electric power; • Loss of friable ore minerals and fines stuck on conveyances and in chutes; •Need to use more expensive methods and explosives; and •Decrease productivity of equipment and personnel. Expressed as cost per unit of ore produced, these unquantified costs can be high. Ideally, advanced dewatering should eliminate most of them. Advanced dewatering is a highly effective water control method, but it isn't problem free. Mines in ideal ground for advanced dewatering are most unusual. To be effective, water must be pumped at a comparatively high rate for a period longer than the life of the mine, from below mining depth. Effects on both groundwater and surface water are likely to be drastic. of increasing mine water costs are listed in the accompanying table. Ten groups of possible methods are cited. Most have been demonstrated in mining; two are known from industries other than mining.

Jan 12, 1980

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant. able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). [ ] The most recent development, however, is the use of H2O2 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). [ ] Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: Hydrogen peroxide must be diluted before it is added to the pulp. The dosage of H2O, must be properly regulated based on the oxygen level of the pulp. An important part of the continuous O, control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1990

By E. G. Joe

Introduction Uranium mining has been actively carried on in Canada for over twenty-five years mainly in Ontario at Elliot Lake in Bancroft, and in Northern Saskatchewan at the operations of Eldorado Nuclear Ltd. During this period, approximately one hundred million tons of mill tailings have been created and lie mainly on the surface close to the mining and milling installations. If all of the present reserves of uranium ores in Canada are mined, a further eight hundred million tons of mine tailings could be created in Ontario, Saskatchewan, the Northwest Territories, Labrador and British Columbia. The present control of effluents from existing tailings is managed by the operating mines under the regulations of both federal and provincial control agencies. It is the long-term effect of these tailings on the environment that has not been clearly defined or measured. Several years ago, the Canada Centre for Mineral and Energy Technology of the Department of Energy, Mines and Resources, embarked upon a program of research directed at the long-term effects of uranium mine tailings. Much of the research to date has been on tailings in the Elliot Lake, Ontario area where some tailings piles have existed for over twenty years. The program consists of two projects, one to address the problem of existing tailings and the other to examine alternatives in the management of current and future tailings. TAILINGS CHARACTERISTICS Uranium tailings are generally the result of sulphuric acid leaching in which the uranium and alkaline minerals such as carbonates and chlorites are leached out. If the ore contains sulphides, these minerals potentially present an additional hazard of acid generation over time and could increase the mobility of heavy metals and some radionuclides such as thorium-230. Except for the extracted uranium, most of the radionuclides from the ore remain in the tailings pile. Uranium ores in Canada span a wide variety of mineralization and associated gangue composition. Uranium minerals include pitchblende, uraninite, uranothorite, brannerite and the phosphate uranium minerals autunite and saleeite. Gangue minerals vary from acid consuming carbonates, and chlorites to acid producing sulphides and inert silicates. With such a wide variety in ore composition, the characteristics of the resultant tailings in Canada are in many cases site specific and the solutions to the long-term effects of these tailings may also be site specific.

Jan 1, 1980

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993

By R. M. Williams

Introduction Ring roller mills are efficient size reduction machines embodying the following machine functions: 1) Size Reduction: from a feed size of 2 in. to various size products as fine as 400 mesh, or granulation from 2 in. to 6 mesh containing a minimum of fines. 2) Drying: fluid bed drying of wet feed materials. 3) Conveying: negative pressure air system results in dust-free conveying. 4) Beneficiation: liberation and removal of foreign materials from the auxiliary bottom discharge simultaneously while grinding. Operation Operation of the roller mill system, Figs. 78 and 79, is completely automatic. A feeder introduces raw material into the grinding chamber in the base of the roller mill at a rate determined by pressure variations within the roller mill as material is ground and air conveyed away. The feeder will be activated by the reduced static pressure and introduce unground material into the system, thereby maintaining a constant differential pressure. Plows located ahead of each grinding roll direct the material upward and between the grinding rolls and the bull ring where it is ground to size. The grinding rolls are free to swing out centrifugally, which forces them to bear upon and grind the raw material. Being free to pivot axially, the rolls automatically assume the proper position for grinding and need no adjustment to compensate for wear. Rotation of the rolls is by rolling contact. Once ground to size, material is swept out of the mill by the controlled air flow from the centrifugal main mill fan. Air suspended, the ground material passing through the adjustable spinner separator. In the separator, an accurate size classification is made which allows product-size material to be conveyed away from the roller mill while oversize material is returned internally for additional grinding. By varying the speed of the separator drive, more or less cyclonic action is achieved at this location, effectively controlling product size. Product sized material is removed from the airstream by the cyclone collector. Typically, a conveyor or product storage bin will be located to accept the product as it exits from the bottom of the cyclone collector.

Jan 1, 1985

By Alan T. Nelson, Ronald D. Mariani

The Tilden concentrator was originally constructed in 1974 for the processing of low grade hematite. Flotation is a key concentrating process in the operation, and therefore flotation optimization has been a major concern since the plant startup. This paper will discuss some of the modifications made in the process to achieve optimization. The conversion that now enables the plant to process magnetite as well as hematite also will be discussed. INTRODUCTION The Tilden Mine, located in Ishpeming, Michigan, is managed by Cleveland-Cliffs Iron Company and is owned by Cleveland-Cliffs and two Canadian steel makers. It was constructed and started production in 1974 and expanded in 1979 for processing a low grade, fine-grained hematite iron formation for which there was previously no technology available. Several papers have been written describing the unique character of the concentrating operation. The hematite plant consists of 12 grinding and concentrating lines, which utilize two stages of autogenous grinding with crushing of an intermediate sized product. The ground product is deslimed in a highly dispersed alkaline environment to reject silica. Corn starch, the flocculant, has a high affinity for iron at the operating pH range of 10.5 to 11.0. The ore is upgraded from 35% to 45% iron in the desliming step. The deslime thickener underflow is the feed to flotation. Each flotation line consists of a bank of 10 rougher cells, followed by four scavenging banks incorporating 5, 4, 3, and 3 cells each. The Wemco flotation cells are each 14.1 cubic meters (500 cubic feet) in volume. A total of 12 flotation lines are available. [ ] A reverse flotation process is employed, using a straight-chain, 8 to 10 carbon primary ether amine silica collector. At the levels used in the circuit, the amine also serves as a frother. A final concentrate is produced in the rougher cells. The concentrates from the four scavenging steps are combined and recirculated to the feed end of the roughers, with the fourth scavenger froth being discarded as a final tailing. Upgrading to about 65% iron is achieved, with control of the circuit based on final concentrate silica grade. Starch is again used, this time as a depressant for iron. During the years of operation, several key areas of the flotation process have been targeted for optimization. The most significant improvements have been realized in the following areas: *Grade Control Automation *Control of Water System Chemistry *Flotation Spray Water This paper will focus on these areas, but other minor improvements also will be briefly discussed.

Jan 1, 1993