Search Documents

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By R. L. Eppley

The Blacklick Creek Watershed Association was awarded a $158,000 Growing Greener grant from the Pennsylvania Department of Environmental Protection in 2002 for the design and construction of a sulfate reducing bioreactor (SRBR) cell to treat acidic discharge from the Judy 14 abandoned underground coal mine near Indiana, PA. The vertical flow SRBR was designed to treat 38 liters per minute of MIW containing elevated concentrations of aluminum and iron. Other treatment systems at this site plugged due to aluminum precipitates; this problem did not occur in the SRBR. The bioreactor has been periodically overloaded with flows up to six times the design rate. To date, the only maintenance performed on the unit has been the addition of hay to the surface of the unit in response to less than expected performance. The periodic hay additions appear to have restored the SRBR to nearly post-construction levels. Since construction, the SRBR has treated about 136,000 cubic meters (36 million US gallons) of MIW.

Jan 1, 2010

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By G. B. J. Leon, M. Karmis, C. Newman

"The prediction of surface deformations due to underground mining operations has been a long recognized practice with case studies documented as far back as 1556 in Georgius Agricola's De Re Metallica (Latin for On the Nature of Minerals). There is currently increased public awareness and regulatory scrutiny on the potential impacts of underground longwall and second mining operations, but this time the focus is placed on environmental impacts to overlaying bodies of water such as streams, rivers, wetlands, lakes, etc. (Karmis and Agioutantis, 2015). Community residents and environmental groups, as well as federal and state regulatory agencies, have often cited adverse stream impacts and demanded stronger measures and scrutiny in issuing mining and reclamation permits (Booth, 2006). Mining companies are required to focus on the protection of sensitive bodies of water through the monitoring of stream flow and water quality, management and rehabilitation techniques, as well as the adoption of ""no mining zones,"" which potentially sterilize large portions of minable coal reserves. This paper examines the use of an empirical modeling approach for the protection of surface streams based on evaluation of ground strain magnitudes. Utilizing enhanced features of the Surface Deformation Prediction Software (SDPS), ground movements can be predicted accurately in the vicinity of surface bodies of water. The modeling of ground movements can aid in establishing optimum extraction sequences, while the magnitudes of anticipated subsidence can be used in the evaluation of mitigation plans when undermining surface bodies of water. INTRODUCTION When utilizing high recovery underground mining methods, such as longwall or room-and-pillar mining, the movement and deformation of the overburden propagates toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope, and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidence initiated changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, subsidence induced strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed, ""ruptures,"" upward blocking stream flow or having the stream diverted into the facture zone at the base (Iannacchione, et. al., 2010)"

Jan 1, 2016

By Thomas Schwind, Benedikt Grau, Angelos Gakis

"In Crossrail’s Farringdon station, compensation grouting was successfully utilized to mitigate the surface settlements induced by the tunneling works. The main focus of this study was the platform tunnels, which were approximately 300m long each and were enlarged to platform size using sequential excavation method (SEM) from the existing TBM running tunnels, initially supported using sprayed concrete linings. The rear grouting injections were carried out at a typical distance of minimum 5m above the completed, fully strengthened shotcrete lining hence inducing some additional stresses. In-tunnel monitoring using surveying targets was performed systematically to ensure that no excessive distortion of the initial shotcrete lining occurred. 3D finite element analyses were utilized to back calculate the actual “effective” pressure that was imposed on the completed shotcrete rings against the additional measured in-tunnel displacements due to the compensation grouting episodes. Additionally an assessment of the theoretical, “maximum” allowable grouting pressures that would lead to overstressing of the lining is presented. INTRODUCTION As part of the back analysis performed for the SEM tunnels in Farringdon station, an investigation of the effect of compensation grouting on the two constructed platform tunnels was undertaken. The platform tunnels were 10.6m high by 11.4m wide and approximately 300m long each. They were enlarged to their final shape from the existing TBM tunnels using SCL methods. This study utilized 2D and 3D finite element (FE) analyses in order to back calculate the observed tunnel crown displacement, assessing the equivalent grouting pressures during the rear injection episodes of the concurrent grouting operations. The results provide a useful reference for the order of magnitude of the grouting pressure load cases that can be applied in the numerical simulation of similar cases. Part of the results presented in this paper, were derived by the second author as part of his Master of Science thesis in Technical University of Graz."

Jan 1, 2016

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By R. Bernard

This paper will discuss innovative strategies that combine the capabilities of an Enterprise Asset Management (EAM) solution, sometimes referred to as a Computerized Maintenance Management System (CMMS) and E-Commerce solutions. Strategies discussed include solutions that minimizes the costs of operations through maximized equipment productivity and availability. Thusly, achieving the ultimate goal of keeping the cost per production unit as low as possible.

Jan 1, 2001

By Deepak Malhotra

Western technology is considered a panacea for all ills in developing countries. Is that really the case? Are inventors of new technology overselling? What are the expectations of the receiving party? The author offers his views on these questions and proposes a process for systematic transfer of technology while minimizing surprises on the part of the seller and the receiver.

Jan 1, 2001

By D. A. Harman

The U.S. Environmental Protection Agency recently recognized Newmont and other mining companies, along with the Nevada Division of Environmental Protection for their voluntary work in reducing mercury air emissions. One example of this voluntary effort is the installation of a reactive scrubber to capture mercury vapor from the exhaust of a carbon regeneration kiln at Newmont’s Twin Creeks Mine. After considering the available technologies, a proprietary reactive scrubber, developed by ADA Technologies, Inc., was selected and is currently being commissioned. Mercury removal rates greater than 90% have been documented.

Jan 1, 2004

By S. Bhattacharjee, S. K. Singh, R. K. Galgali

A method for the preparation of zirconia- toughened mullite using dc plasma is presented. An indigenously developed 50-kW thermal plasma reactor is used for the preparation of zirconia-toughened mullite using a dissociated zircon and alumina mixture. Both XRD and SEM studies of the product confirmed the formation of mullite and zirconia. The zirconia grew as equiaxed grains of uniform size (~5 µm) in a mullite matrix.

Jan 1, 2002

By H. Schultheis

The European Commission has launched in April 2002 the Thematic Network NESMI with-in the FP5 under Growth. NESMI stands for ?Network on European Sustainable Mining and Processing Industries? and will run until 2005. Within NESMI there are different ways to set up indicators and evaluate them throughout the NESMI Members. First analyses concerning the Demand and Competence within NESMI are developed. New focus points for analyses can be implemented into NESMI.

Jan 1, 2003

The research deals with the study of the quality indicators in the productive process and its use for the consuming market, for two types of ores: industrial sand and crushed stone. Companies who represent the profile of the São Paulo producing market in its respective modalities well produce the selected cases. The development of the studies have to be, for the application of consistent methodological models of the fundamentals of the Engineering of Quality, especially how much to the statistical control of processes and its trustworthiness, of form that the results of the research can serve as referential in the boarding for other generic cases of the mineral industry.

Jan 1, 2003

By Tien H. Wu, Pinnaduwa H. S. W. Kulatilake

The concepts of conditional probabi1ity and geometrical probability are used to establish a relation between the probability density of the trace length and the probability density of the discontinuity diameter. The discontinuity is represented as a thin circular disc. A numerical solution scheme is used to obtain the probability density of the disc diameter from the probability density of the trace length. An example was used to illustrate the possibly large difference between the mean discontinuity diameter and the mean trace length.

Jan 1, 1986

By Alwyn Protheroe, Steve Smith, Herbert Jr. Gibson

In September of 2000, Cowin and Company, Inc., contracted with Paramont Coal Corporation to construct a large decline approximately 820 m (2,700 feet) in overall length at a grade of 8 degrees to the Lower Banner Coal Seam. This paper will discuss the methods used by the contractor and owner to overcome the unique problems required to construct this tunnel in a coal mine environment. The problems include, initial design considerations, equipment selection, ventilation, ground control, control of water in?ows, and placement of concrete.

Jan 1, 2003

By Jorge Martinez

The Muck Valley Hydroelectric Project in Northeastern California required construction of a 3.65 meter tunnel through 6,623 meters of mixed volcanic flow deposits within a critical time frame. As Engineer and Construction Manager for the Project, Morrison-Knudsen Engineers invited bids for both Drill and Blast as well as Tunnel Boring Machine methods, selecting a contractor proposing a TBM designed and built specifically for this project which could excavate a wide variety of materials and maintain acceptable progress rates to complete the work within schedule. Tunnel lining as required included shotcrete with metal fibers and full circle concrete.

Jan 1, 1989

By Glenn M. Boyce, Timothy R. Coss

Microtunneling first appeared with some regularity in the United States in 1987. Until then, only Japan and Germany utilized this method of construction. Its high costs initially limited its application to special situations. The last ten years have seen the use of new pipe materials, new machines, new cutterheads, new techniques, and an average growth of30 percent each year. This paper documents the growth and changes that have occurred with microtunneling. Based on current industry practices and advances from abroad, this paper postulates what the next ten years may hold.

Jan 1, 1997

By Gordon F. Revey, Dan Harrison

Hanging Lake Joint Venture recently excavated two conventional 12.8 m (42 foot) diameter highway tunnels in the difficult ground conditions of Glenwood Canyon, Colorado. This paper outlines the type and success of the various Controlled Blasting Techniques that were used to minimize overbreak in the portal and tunnel excavations. The different Smoothwall and Cushion Charge loads used in the different ground types are described in detail. Delay Timing and Drilling Pattern variations are also discussed.

Jan 1, 1991

By Maurice Deul

Limestone can be used effectively in treating acid mine water. Aside from a lower cost than for other treatment agents, limestone has the advantages of easy storage and effectiveness even when impure and in slack sizes. Limestone incorporated into waste piles in layers or as riprap can inhibit acid formation; limestone rubble packed in a mine entry offers promise in formation of a low-cost autogenous resilient seal.

Jan 1, 1974

By D. C. Panigrahi

The paper presents the application of Object Oriented Programming approach for the development of a network simulation model based on nodal pressure method using linearised flow equations. The convergence and computational efficiency of the algorithm have been investigated. Finally the paper re- ports the validation of this algorithm in actual field conditions.

Jan 1, 1996