Search Documents

By G. B. Misra

Heat transfer in partially wet mine airways has been the subject of study for quite some time. Of the available models some are quite empirical while some involve highly complicated computation. Models developed by Amano, Mizuta and Hiramatsu and Banerjee and Chernyak as well as that modified by Misra were evaluated for prediction of the rise in temperature and humidity (mixing ratio ) of partially wet mine airways at four different levels in the Mosaboni Mine of Hindustan Copper Ltd. Measurements of barometric pressure, virgin-rock temperature and changes in dry- and wet-bulb temperatures along a certain length of airway were made. The rise in dry-bulb temperature and mixing ratio of air over the sections were calculated using the three models. The study reveals that calculated values of temperature and moisture content agree within possible rage of experimental error with all the three models in case of three levels with low wetness factor, but the agreement was poor for the relatively more wet airway on the 30th level. Errors in the estimation of fw to the tune of 0.025 can lead to fair error up to 0.94 K in the estimated temperature while alternative ways of estimating the heat transfer coefficient [] can introduce errors up to 1.45 K.

Jan 1, 1987

By John Nadolski

Intensive hydrologic monitoring of the Powder river basin has been on-going since the early 1970's. Data were used in environ- mental assessments and for determination of hydrologic consequences associated with coal mining activities. For most coal mine operators, data collection has continued in this baseline mode with little or no statistical analysis of the data and with no statistical procedure established to detect changes in groundwater quality. For the past four years Powder River Coal Company has studied several statistical techniques to analyze groundwater quality. Three objectives were pursued: 1) to determine the baseline water quality for key aquifers; 2) to determine which wells could be deleted from the monitoring program without reducing monitoring effectiveness; and 3) to define a statistical test to determine water quality changes. Knowledge of the regional geo-hydrologic system was combined with an analysis of the water quality monitoring in order to identify homogeneous aquifer zones. All wells within an aquifer zone were treated as one population, and a t-test was used to determine the minimum number of samples needed to define the water quality for each aquifer zone. Results indicate that the data for each aquifer zone were nor- mally distributed and that groundwater quality could be defined using a fairly small number of samples. Because of the minimum sample size test, groundwater quality sampling was reduced by between 75 and 85 percent.

Jan 1, 1989

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By A. C. Burrow, R. P. King

A dynamic model that predicts the variation of carbon content with time in the argon-oxygen decarburization (AOD) process has been developed. The model recognizes three distinct zones in the AOD vessel: the tuyere region in which the blown oxygen reacts very rapidly with the metal components in the molten alloy; a region in which bubbles of inert gas and oxide drop lets rise through the molten alloy; and a zone in which the slag layer can interact with the molten alloy. The process is dynamically controlled by the rate at which dissolved oxygen, produced on the surface of rising oxide droplets, and dissolved carbon diffuse through the molten alloy to react at the surface of the rising bubbles. The rate at which carbon and oxygen react on the bubble surface is assumed to be intrinsically very fast. Predicted decarburization rates compare reasonably well with rates measured in the AOD vessel at Middleburg Steel and Alloys. The model has been developed primarily to allow development of a time-optimal blowing stategy for the AOD vessel.

Jan 1, 1990

By F. F. Aplan

The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.

Jan 1, 1988

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

By Joseph Lynch, John DiPonio

This report refers to the Chicago Deep Tunnel Contract 13A, which was the first contract let in the City of Chicago requiring the construction of deep drop shafts for the transportation of high level sewage to the deep tunnel system. The basic contract required the contractor to construct certain drop shafts designed to deliver surface and high level sewage to the deep tunnel system approximately two hundred feet below. The design of the drop shafts was in a degree affected by their proximity to the existing deep tunnel. The tunnel, approximately three and one-half miles long, was to have five shafts dropping sewage at five locations. Four of the drops were approximately one-half mile apart and spaced from the dead end of the tunnel. One shaft divided the remaining two miles from the existing work shaft at the southeast end of the tunnel wherein a 220' deep pumping station was to be built. The existing tunnel had been built some time previously and all dewatering had stopped, allowing the tunnel and main shaft to fill with water. According to the plans, the drop shafts were all between fifty and ninety feet north or south of tunnel center line, and located in heavily built-up residential and industrial property. This then defines the problems: How do we control the water. If we excavate from the top down, how do we handle the slurry and the muck from five locations. How shall we construct the connecting tunnel between

Jan 1, 1997

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By Joginder S. Bhore, Francis M. Keville, David E. Puza, Roger C. Borggaard

A portion of the Massachusetts Bay Transportation Authority's Red Line Extension through Somerville, Massachusetts consists of 1,553cm (5,092 LF) of hard rock tunneling 6.7m (22 ft.) diameter horeshoe, 148m (485 LF) of mixed face tunneling, 7.2m (23 ft.) diameter circular, beneath an active railroad in a heavily commercialized business district. This paper will deal with the excavation of the mixed face area without the use of a shield. It will address the special excavation and support problems encountered during tunneling operations using the floating crown bar and modified spiling methods. Topics covered will include excavation and support methods, cement grouting, compaction grouting, and instrumentation. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnels and Shafts Somerville/ Cambridge, Massachusetts is part of the Massachusetts Bay Transportation Authority's (MBTA) 5.1km (17,000 ft.) Red Line Extension. This extension runs from Harvard Square, Cambridge, to Alewife Brook Parkway, Cambridge through Somerville. This portion (MBTA Contract #091-106) required the excavation and concreting of 1,701m (5,580 LF) of single track twin tunnels consisting of 1,553m (5,092 LF) of conventional hard rock tunneling under 56 residential properties and 148m (485 LF) of mixed face tunneling beneath an active railroad in a heavily commercialized business district. The mined diameter of the mixed face tunnel is 7.16m (23.5 ft.) Access to the tunnel was via the Summer Street vent shaft, and the two Grove Street access shafts where all tunnel excavated materials were removed.

Jan 1, 1981

By W. Morgan, D. Gove

In truck and shovel operations, productivity and cost per ton are influenced by the system matching choice, Optimization involves a balance of the size and number of trucks, the size and type of loading tool and the projected material conditions and haul roads. Caterpillar has updated its Fleet Production and Cost program so miners can more easily look at matching choices and optimize on the variable they choose. This paper introduces the Fleet Production and Cost program. It then demonstrates its capabilities with examples of optimization. Mining operations that use trucks need to properly match the number and size of hauling units (trucks, wagons, scrapers, etc.) to a loading unit (wheel-loader, hydraulic shovel-excavator, cable shovel, push tractor, etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length, grade or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool that can be used to optimize the truck-loader match.

Jan 1, 1995

By William C. Cooley

Modern tunnel boring machines are subject to excessive cutter wear and bearing failures when used in hard and abrasive rock. In very hard rock, the high cost of cutter and bearing replacement, combined with slower excavation progress, make it more economical to drive tunnels by conventional drill and blast methods. The use of high pressure water jets to break rock provides a promising alternative. Experimental data indicate that the specific energy (the energy expended per unit volume of rock broken) decreases as the water jet pressure increases. Continuous jets are generally limited to pressures below 100,000 psi, whereas pulsed jets from a water cannon can attain much higher pressures. Therefore, the Federal Railroad Administration of the U. S. Department of Transportation has sponsored the design (Ref. 1 & 2) and the fabrication and testing (Ref. 3 & 4) of a water cannon to determine its effectiveness in rock disintegration at very high pressures. This paper reports the results of laboratory tests with pulsed jets against large rock samples at pressures of 125,000 to 650,000 psi and field tests against dolomitic limestone and granitic gneiss at pressures near 450,000 psi. Although initial tests were made with a small nozzle, operating at off-design conditions (Ref. 4), this paper only covers results with the full-size nozzle, including 55 laboratory test shots and 67 field test shots.

Jan 1, 1974

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By James S. Hanson

Existing models proposed for the bacterial leaching of metal sulfides generally fail to predict solubilization rates at times greater than a few tens of hours. The reasons for this may be that these models are empirically based and use first order bacterial and chemical oxidation rates. This type of model is satisfactory for short time predictions (on the order of 20 hours) when the bacterially catalyzed dissolution is relatively minor. However, when bacterial action becomes more pronounced, these models consistently predict higher dissolution rates than those commonly observed in laboratory experiments. The present model uses several fundamental chemically and biologically based assumptions to predict the dissolution rate of a chalcopyrite concentrate for extended leach times up to the precipitation of jarosite. The main assumptions made are that Monod growth kinetics prevail, T. ferrooxidans adsorb onto the surface of the mineral (not necessarily mineral specific), and that during periods of high growth oxygen transport may become rate limiting. The model also relies on the energy efficiency of the bacteria in fixing carbon (growth yield) and correlates this value with available surface area of the mineral particles and the bacterial growth rate.

Jan 1, 1989

By I. Iwasaki

As the world tension relaxes and as the interest and taste for consumer products change, complacency is beginning to prevail over the needs of minerals and primary metals. The current trend towards resources and energy conservation calls for miniaturization of consumer goods, and lowers the demand for virgin materials to produce goods and services. Challenged by the third world countries with high grade ores and low labor costs, industrialized nations with lower grade ores are being pressed into more efficient operation through technological innovation, while protecting the environment. In many countries, domestic mines were forced to close since the oil crises due to rapidly rising energy and labor costs. Research in conventional mineral processing needs to be directed towards breakthrough technologies in order to maintain the competitive edge in the global marketplace. Research activities will provide new challenges in the processing of solid waste and waste water for environmental remediation as well as for resource conservation, in the preparation of new functional materials of extreme purity and/or unique properties for high technology applications and in the development of such future resources as deep sea minerals and extraterrestrial materials.

Jan 1, 1995

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By R. Addison, P. V. Avotins, D. W. Kestner, M. F. Dibble, L. A. Haas, M. D. Flavel, D. Halbe, D. J. Barratt, G. V. Jergenaen

Mineral processing in 1980 can be described by several key words, familiar to the industry throughout the past decade: complex, low grade, environmental, energy, high tonnage, and economics. Flowsheets have become more complex in order to treat lower-grade, finer-grained, more complex ores and still meet environmental and economic constraints. Operators and researchers have had to cope with these problems, which have resulted in marked trends in mineral processing. The use of advanced instrumentation in process monitoring, control, and modeling has been increasing to deal with fluctuating ore grades, higher plant capacities, rapidly rising operating costs, and process complexities. The industry has been presented with new generations of equipment that reportedly do the job more efficiently and at a reduced cost. The need to meet stricter air and water environmental standards has resulted in a concerted effort by the mineral industries to obtain an appropriate balance between the needs of mining and mineral processing and the requirements for proper environmental, safety, and health protection. Energy and economic considerations have led to increased equipment size, particularly in grinding, flotation, and conveying. Throughout all phases of mineral processing there has been an effort to reduce energy consumption. One avenue followed by researchers and operators was the testing and use of chemicals to reduce energy requirements.

Jan 5, 1981

By Salt Lake City Research Center, D. G. Foot, J. D. McKay

As part of its research program on column flotation, the Bureau of Mines, Salt Lake City Research Center has performed studies on (1) column flotation amenability and comparison with conventional flotation results for over 15 mineral systems, (2) alternative methods for improving column bubble generation systems, (3) mineral behavior within a column, and (4) the effect of changes in column operating parameters on flotation grade and recovery. Based on results from these studies, flotation columns (1) are capable of producing higher grade concentrates in fewer stages than conventional flotation cells at equivalent or increased recoveries, (2) require less retention time than conventional flotation cells, and (3) can be divided into cleaning and collection zones that have characteristic mineral-upgrading-per-foot values. Attempts to improve the column air sparger have led to the development of a superior external bubble generation system, which can (1) achieve increased air holdups. (2) produce bubbles from 400 Um to 4,000 Um average bubble diameter with minimal frother addition, (3) provide superior bubble size control, and (4) be maintained without column shutdown. Efforts are continuing to improve column flotation and transfer successful technology to industry.

Jan 1, 1988

By R. Worrall

The global mining industry has been proactive over the last decade in finding ways to embrace the concept of sustainability. However, legacy mine sites (which include abandoned derelict and orphan mine sites) across the world continue to present issues for the global mining community, governments, local communities and NGOs. Unfortunately there has been much less academic focus on this area of mining and sustainability. This paper seeks to address how principles of sustainable development can be used to guide the development of processes for addressing post mining landuse issues for legacy mining areas. This is being done using a case study area located near Ipswich, in southeast Queensland, Australia. This area has a 160 year history of coal mining, and was one of Queensland?s crucial early industries. Mining in the area ceased in 2003 leaving a degraded landscape covering an area in excess of two thousand hectares adjacent to one of the fastest growing urban areas in Australia. A sustainability criteria and indicators framework for post-mining landuse on legacy mined land, developed from current best practice used for measuring sustainability across a range of industries is being developed. A review of current best practice suggests the framework should: (1) consider in equal measure environmental, social and economic factors; (2) have a minimum number of indicators which should be easy to identify and measure; (3) must have indicators with a meaningful output; and overall, the framework must consider particular requirements of the site being investigated. Application of the framework to the case study area is an ongoing aspect of this research, and the results will be evaluated through the use of expert stakeholders.

Jan 1, 2007

By Angelus S. C. Owili-Eger

The past decade has witnessed an unprecendented proliferation of groundwater computer models. Some of these numerical models were developed for the purpose of simulating groundwater movement in mining environments and predicting inflow rates into active mines. However, a general acceptance of these models as routine planning tools by the mining industry has been slow. Until recently, the major use of these models in the industry is by consultants. There are several reasons that have contributed to this situation. Some of these factors - include scarcity or non-existence of an appropriate data base information required for executing these models, the difficulty and costs involved in acquiring data, and the fact that the instructions for using these models are often too involved and time consuming. Today, however, the state-of-the-art technology has been advanced to a level where numerical models can be routinely used to simulate and predict inflow rates into active mining environments. Such environments include highly fractured (longwall) and deforming flow media. Features integrated into these comprehensive and yet easy to use models are double-porosity-pressure, multiphase, and non-darcian flow conditions. This paper reviews the role that computer modeling has played in mining-related operations by presenting several case studies and the state-of-the-art tools currently in use. Included will be some of the practical field applications that have been compiled during the past decade.

Jan 1, 1986

By J. D. Pitts

Long distance slurry pipeline systems for steam coal, iron concentrates, copper concentrates, and limestone, first used nearly 60 years ago, are now transporting nearly three billion ton-miles annually. At this time a phosphate concentrate pipeline is nearing start-up and systems for transporting coking coal, lead/zinc concentrates, and fly ash are planned. The solids pipeline concept was first patented in the early 1900's and put into practice in the 1950's. Table 1 summarizes the major elements of several presently operating commercial systems. Increased control system sophistication has been accompanied by significant drops in control equipment size and cost, as illustrated by recent cases of pipeline operation with progressively more advanced level of control: 1) The Consolidation Coal (Ohio) and Savage River (Tasmania) iron concentrate pipelines started in 1957 and 1967, respectively, used simple hard-wired control logic. 2) The Black Mesa (Arizona) coal slurry pipeline commissioned in 1971 added a hard- wired programmable logic controller for some of the start-up and shutdown routines. 3) Two years after its start-up in 1974 the Pinto Valley (Arizona) copper concentrate pipeline was tied into the concentrator digital computer system for data logging. 4) The Samarco (Minas Gerais, Brazil) iron concentrate pipeline which came on-line in mid-1977 was the first slurry system to use a dedicated supervisory computer for its control. Communication to remote areas was via micro- wave and buried cable.

Jan 1, 1979