Search Documents

By K. D. Luxbacher, J. T. Davis

"A wind tunnel was designed to examine air flow, heat transfer and layering near an active fire at a working face. This tunnel simulates an active entry in an underground coal mine including an attached cross-cut of similar dimensions. A steel rectangular duct 1 ft. (0.305 m) tall, 3 ft. (0.914 m) wide and 10 ft. (3.05 m) long composes the main body of the tunnel and represents a mine entry. Air flow is generated by an exhausting centrifugal fan attached to one end of the crosscut. This fan was sized to supply air velocities based on Froude scaling. A 6 in. (15.25 cm) propane burner is used to simulate fires of various heat release rates at the working face. Thermocouples are used to map heat layering in the tunnel. Ports are installed for the introduction of tracer gases into and from sampling the system. Barometric, differential pressure, and temperature sensors are also included to monitor environmental conditions. Details about the design and testing of the system are presented including an overview of how the tunnel was scaled to accurately represent fire and flow phenomena. Finally, the proposed use of the tunnel for better understanding of mine fire phenomena and prevention is given. INTRODUCTION Fires in underground mines have been a concern since the dawn of mining. While technological advancements, regulations and best practices have improved both fire detection and firefighting techniques, mine fires continue to represent high risk events. From 2006 through 2015, fires accounted for 1.06% of fatalities in underground coal mines and 0.85 percent of fatalities in all underground mines in the United States (U.S. Department of Labor, 2006 to 2015). In addition to the risk of loss of life, mine fires can cause millions of dollars in equipment damages and lost production revenue. Extensive research has been conducted on how fires occur and spread in underground mines. In addition to testing conducted by government agencies such as the Mine Safety and Health Administration (MSHA) and the National Institute for Safety and Health (NIOSH) (e.g.(Liming, 2006), researchers like Verakis and Dalzell (Verakis, 1988) and Lowndes, et. al. (Lowndes, 2004) have furthered this field by studying ignitions and propagation of conveyor belt fires. While the studies of belt fires in mines are extensive, studies focused on fires at the working face are few in number. The particularly confined space and limited access to a working face, coupled with less robust, temporary ventilation controls create a unique environment that warrants special attention. Separate from studies on mine fires, the use of tracer gases to characterize flow patterns in normal mining ventilation is well established. In 1982, Timko and Thimons (Timko, 1982) outlined current and future applications of sulfur hexafluoride (SF6). However, little experimentation has been conducted to study specifically how tracer gases might be used to evaluate active mine fires and the fires’ effect on the surrounding mine environment (e.g.(Lindsay, 2014). In order to better understand the dynamics of smoke layering from a fire in an enclosed space, a small-scale apparatus was designed to map smoke layering and to examine other aspects of fire behavior at a working face. In addition to studying smoke flow around an active fire, experiments will be conducted using tracer gases in order to determine how they might be used to evaluate an underground fire."

Jan 1, 2017

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-adsorbed onto clay surfaces or inner layers, or organically bound. Rare earth minerals such as monazite exist in coal and have grain sizes smaller than 5 µm. In this study, froth flotation was successful in concentrating rare earth minerals existing in a thickener underflow material derived from Fire Clay seam coal that contained around 431 ppm of total rare earth elements (TREE) on a dry ash basis. Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2,300 ppm TREE. Using a laboratory flotation column to limit hydraulic entrainment, the TREE content was further enriched to around 4,700 ppm, which equated to an enrichment ratio of 10:1.IntroductionRare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets and batteries (Binnemans et al., 2013; Zhang et al., 2015). REE recovery from alternative sources such as coal and coal byproducts has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials.The average REE content of the world’s coal resources is around 60 to 70 ppm (Zhang et al., 2015). There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia with contents of 300 to 1,000 ppm, the Fire Clay coal seam in eastern Kentucky in the United States with contents around 500 ppm and the Sydney Basin in Nova Scotia, Canada, with contents of 72 to 483 ppm (Birk and White, 1991; Seredin, 1996; Hower, Ruppert and Eble, 1999; Blissett, Smalley and Rowson, 2014). The occurrence of REEs in coal and coal byproducts can be classified into three types: (1) rare earth minerals, such as monazite and xenotime, (2) ion-adsorbed REEs on clays and (3) REEs associated with organic matrices. The rare earth minerals in coal and coal byproducts are very small in particle size, generally on the micrometer and/or nanometer scales (Honaker et al., 2014). Froth flotation, which concentrates minerals based on surface chemistry differences, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime and bastnaesite (Abeidu, 1972; Cheng, Holtham and Tran, 1993; Pavez and Peres, 1994; Pavez, Brandao and Peres, 1996; Jordens et al., 2014). As such, flotation is a promising method for the concentration of rare earth minerals from coal and coal byproducts."

Jan 1, 2017

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994

By L. Bloom

"Man-Made Parameters" refers to the importance of selecting appropriate analytical procedures to acquire useful chemical data. The correct procedures are particularly critical at the sample preparation stage where decisions concerning pulverizing equipment, sample size, contamination and dissolution will impact on the final results independent of the instrumental method of analysis. Several experiments were designed to quantify the impact of these approaches.

Jan 1, 1993

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Jue Kou, Fazhao Sun, Jiang Liu, Cuili Gui, Baoqiang Yu, Chunbao Sun

A novel special magnetic separator was developed based on the special properties of precious metal-bearing alloy in highgrade nickel matte. The recovery of Au, Pt, and Pd was 77.79%, 84.79%, and 81.79% respectively at optimum operation conditions of magnetic separator feed of 2.5t/h, pulp density of 45%, and flush water of 1.5t/h, and the recovery significantly improved comparing with normal magnetic separator. Magnetic field simulation of the special magnetic separator indicates that magnetic intensity of 0.6 T can be generated on the surface of magnetic drum, which can strengthen the recovery of heavy alloy that contains precious metals. The alternate strong and weak magnetic field can also make magnetic particles rolling on the surface of drum, which will reduce the generation of magnetic agglomeration to a large extent and decrease the content of impurities in magnetic concentrate.

Jun 16, 2022

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By D. R. Zeni

Current mine development requires the safe, 'expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994

By J. Szarkowski

"INTRODUCTION The Butte district of Montana is well-known as one of the biggest historic producers of copper in the world. It is also a classic example of a porphyry Cu-Mo system that has been overprinted by zoned, polymetallic (Cu-Zn-Pb-Ag) lode mineralization. After copper, silver was the next most important metal mined from Butte, with over 700 million ounces of total Ag production between 1880 and the present day. Although many papers have been written on the mineralogy of the early porphyry Cu-Mo mineralization and the high-grade Cu-rich lodes in the center of the district, relatively little information exists on the mineralogy of silver in Butte. The purpose of this paper is to summarize past and present silver production trends for the district, and to combine previously published work with new research to examine the mineralogy of silver in the Butte mining district. BUTTE HISTORIC SILVER PRODUCTION According to a recent USGS compilation1, Butte is one of the most Ag-rich porphyry deposits in the world, both in terms of average Ag grade (8.6 g/ton) and total production + reserves (Fig. 1). It is also the 2nd biggest Ag-producing mining district in the U.S. (after the Couer d’Alene district, Idaho). Annual silver and copper production data for the Butte district, compiled from various sources2,3,4, are summarized in Figure 2. Peak production of Ag and Cu was in 1917. While Ag production gradually declined in the ensuing decades, Cu production remained strong until the years leading up to the closure of the Berkeley Pit in 1982. In 1984, mining of the nearby Continental Pit resumed under a different operator, and continues to the present day. The Continental mine produced an average of 35,000 metric tons Cu and 575,000 oz Ag per year between 1984 and 20044. These figures do not take into account a period of mine closure in 2001-2003 due to an unexpected hike in utility prices. The long-term decline in Ag/Cu ratio of ore mined in Butte (Figure 3) is due to several factors, including: 1) changes in metal prices; 2) a downwards decrease in Ag/Cu ratio of most of the lodes with depth below surface; and 3) a shift in mining methods from selective underground mining of high-grade veins to open-pit mining of the bulk rock."

Jan 1, 2016

By Deepak Malhotra

Is operator training necessary for optimization of flotation plants? The answer is obvious-Yes. The author suggests a three-phase program for operators when new plants are built or new crews are hired in existing operations. Case examples are discussed to illustrate the benefits of operator training.

Jan 1, 1999

By Anthony Busigin, Stephen Pogorski, Colin R. Phillips

The precision of radon daughter measurement techniques is a complicated function of uncertainties arising from concentration and flowrate fluctuations during sampling, counting statistics and many other factors. Optimization of a measurement technique requires that all these uncertainties - not just counting statistics - be considered. In this work, the optimization procedure of Busigin and Phillips (1980) is tested against Monte Carlo experiments for the case of the modified Tsivoglou method.

Jan 1, 1981

By M. Pantazidou

The wide use of chemical grouts, in combination with increasing environmental awareness, necessitates the evaluation of possible adverse effects if grout constituents may leak in groundwater. Acrylamide-based grouts are of particular interest, since the engineer has to balance the superior properties of these grouts and the known human health impacts of acrylamide. This paper identifies the properties of acrylamide that are required for the evaluation of its fate and transport in the subsurface and presents results of numerical simulations of acrylamide transport for a hypothetical tunneling application.

Jan 1, 2006

By S. Behl

A major limitation in developing successful selective, flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper, a correlation between selectivity of flocculant adsorption and separation efficiency is outlined, and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1994

By A. Chattopadhyay, J. Res

High-level electrical energy can be suitably converted to shock waves of stress that, in turn, may be used for disintegrating hard rocks. This development, known as the electrohydrodynamic method, is very safe and highly economical compared to other methods of rock breaking. This paper deals mainly with development of the equipment and some details of the experimental work carried out with different rocks and concrete block.

Jan 1, 1988

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By D. J. Barratt

The specification of the prime mover of an autogenous-semiautogenous mill involves an analysis of the likely operating conditions within the mill and the choice of a nominal operating speed. For variable speed mills, the operating range for mill speed has to be defined so that mils power-torque requirement can be matched by the motor power-torque capability. This paper describes how thin relationship can be influenced by ore grindability.

Jan 1, 1995

By D. A. Stanley, B. J. Scheiner

The Bureau of Mines, US Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1990

By O. K. Kuznetzov, L. A. Otrozhdenova, N. D. Malinovskaya, I. I. Maksimov, N. D. Khodov

While processing zinc cakes with application of Weltz-technology silver remains unrecovered and goes into clinker. In order to prevent it the elaboration of effective silver recovery methods from zinc cakes before their weltzing becomes necessary. A combined method of zinc cakes treatment with leaching and flotation in a closed water circuit has been worked out. The technological scheme envisages the use of sulphgydril collectors in combination and comprises a series of consecutive operations: leaching, filtration, precipitation(cementing) and flotation. Total silver recovery is approximately 94%. The technology elaborated has been realized in a project by which the construction of a new shop is under way now.

Jan 1, 1995

By A. Mai, J. S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7-m diam primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1987