Search Documents

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By P. R. Segopolo

"The purpose of the project is to convert current shuttle car utilization on an underground coal mine to best practice by focusing on change-out points and tramming routes, which have a major influence on shuttle car away times. Time studies were an integral part of the project as these enabled the determination of shuttle car away times. An indirect proportional relationship between shuttle car away times and productivity is established. Through the time studies, it is deduced that a third shuttle car will make an insignificant contribution to production when there is only one split open. During this time, maintenance on the third car can be optimized. In order to satisfy the mine’s key performance indicator of keeping shuttle car away times less than 75 seconds, a belt extension must be scheduled after the third split is open. It is established that at any given time, a minimum of two shuttle cars should be used. When cutting on the left-hand-side of the belt road with only two shuttle cars available, the centre and left (left of the feeder breaker) shuttle cars should be used for coal hauling. When cutting on the right-hand-side, the centre and the right-hand-side cars should be used. If only one shuttle car is available, the centre car is the most efficient to use. Alternative anchoring configurations can be employed so as to enable cars (left or right, especially) to reach the opposite extremities of the panel and hence minimize cable length restrictions. Paper written on project work carried out in partial fulfilment of BSc. Eng. (MiningEngineering)"

Jan 1, 2015

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By J. C. van Dyk

The objectives of this study were firstly to characterize and quantify the inorganic material in the Secunda gasification feedstock. Secondly, the effect of washing on coal properties and sulphur content was investigated. Coal from a single source and a coal blend from 6 different mines were tested. Composite samples were visually sorted by a geologist in the groups containing roof, floor, C-shale, pyrite, carbonates and siltstone material. Inorganic mineral types from the single source and coal blends were characterized separately. Characterization results indicate that the average mineral matter distribution (mass %) of the coal tested was as follows: carbonates (6%), carbon-shale (19%), pyrite (12%), roof (18%), floor (46%) and siltstone (22%). The roof, floor, pyrite, carbon-shale, carbonates and siltstone in the single source and coal blend have similar chemical properties and characteristics, except for the ash melting temperatures of pyrite and kaolinite in the siltstone. By implementing selective mining and increasing mining management practices, the percentage discard in the run of mine coal can be significantly reduced, by up to 45%, if the mining of roof and floor material can be avoided. No significant impact of mining practices on sulphur content is expected in this case due to the low concentrations of sulphur in the roof and floor material. In summary, selective mining practices will probably result in almost45% decrease in the discard content in the run of mine to gasification, an increase in the carbon content from 55.0% to 58% (air dry basis) and a decrease in sulphur content from 1.1% to 0.9% (air dry basis). It is clear from this study that the main source of sulphur is not in the high ash-content mineral types (e.g. floor and roof), but in situ in the coal structure. Keywords: inorganic material, effect of washing, roof, floor, pyrite, C-shale, carbonates and siltstone

Jan 1, 2005

By J. N. Van der Merwe

"A major shortcoming of the statistical back-analysis of coal pillar strength is that it relies on the asmined pillar dimensions, not taking into account time-related pillar scaling with subsequent reduction in pillar width. The paper describes an investigation where the rate of pillar scaling was applied to the pillars in the databases of failed and unfailed pillars. The reduced pillar sizes were then used in the same method of statistical back-analysis that had been used in the past.This resulted in an equation for pillar strength which predicts significantly greater pillar strength than the previous statistical analyses, which is similar to the strength which had been found earlier by direct testing of large specimens underground. It is concluded that the lower strengths found by previous statistical analyses are due to the incorrect pillar width being used and that by adjusting the pillar sizes to compensate for scaling, more credible results that correspond to direct testing are obtained.As the newly derived strength equation is time-dependent, it follows that the safety factors and probabilities of failure are likewise time-dependant. An equation to determine the probability of failure is also developed. This results in the safety factor being close to unity at a probability of failure of 50%, which is aligned to statistical expectation. IntroductionSince the Coalbrook mine disaster, caused by massive pillar collapse, there have been several attempts at analysing and defining the strength of coal pillars. It was realized in the very beginning that performing classical strength tests on coal specimens in a laboratory and then transferring those results to real coal pillars could not be successful. The scatter of results is one problem and, more seriously, there is a size effect (at least for small specimens) that made the transformation of strength results to much larger coal pillars underground all but impossible.Two main schools of thought then emerged. Some researchers preferred to perform direct strength tests on large specimens underground, while others relied on statistical back-analysis of failed and unfailed pillar cases, attempting to determine the differences in size and shape that would allow a satisfactory prediction of failure. The latter school of thought resulted in the method that was widely accepted by the South African coal mining industry, described in the landmark publication by Salamon and Munro (1967)."

Jul 1, 2019

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By A. Engelbrecht, B. North, B. Oboirien

"There is large electricity generation potential in discard coal, both in stockpiles and current arisings. Power stations with a combined capacity of up to 18 GW electrical (GWe) could be fuelled by discard coal. Modern circulating fluidized bed combustion (CFBC) boilers, with capital costs comparable to equivalent pulverized fuel (PF) boilers, are capable of utilizing discard coal at a high efficiency while reducing sulphur dioxide (SO2) emissions though the use of limestone sorbent for ‘in-situ’ capture.A detailed economic assessment of the feasibility of electricity generation from discard coal, comprising material and energy balances and the construction of a discounted cash flow (DCF) table, shows that it is also potentially attractive from an economic perspective. A base case analysis shows positive net present values (NPVs) and an internal rate of return (IRR) of 21.4%. Sensitivity analyses on critical parameters show that the economic viability is heavily dependent on parameters such as coal cost and the value of electricity. The project becomes unattractive above a coal price of approximately R300 per ton and at an electricity value below approximately 59c per kilowatt-hour (kWh).Site- and project-specific information such as the delivered cost of coal, location and efficacy of sorbents, and effective value of the electricity produced can be used as input to the economic analysis to evaluate siting options and sorbent source options for such a power station."

Jan 1, 2015

By G. Westcott

Impala Platinum, the second largest platinum producer in the world, is embarking on a major expansion strategy to increase its platinum output from 1.95 moz to 2.8 moz by the year 2008. The smelter complex, situated in Rustenburg, will undergo substantial modifications, and will require a solution to the capture and treatment of the smelter off-gases and dust produced during smelting and converting operations. One of the solutions explored was an integrated approach, where all the off-gases from both the primary smelting electric furnaces and the converter operations are routed to a large central gas cleaning and double catalysis, double absorption acid plant. In-line sulphur burning, utilizing a highly flexible LURO1spin cup burner with a turn down ratio of 50%, ensures that the acid plant operates independently of operating conditions at the smelter complex.

Jan 1, 2007

By W. D. Northrop

This paper gives an account of the development of a technique whereby the vertical limits of geological horizons may be identified by the use of vertical variograms on the mineral of economic interest. This information may supplement or guide the correct subdivision of the individual horizons into meaning full data sets by diligent geological observation. This process then improves the quality of the variance modelling of the gold distribution in the plane of the individual layers and therefore enables better estimates to be made into the grids or blocks of the mine model. The technique is explained by an account of the development work, which was performed, on duplicate superimposed reef horizons in the Kimberley formations. The paper then shows how the correct approach was developed to evaluate the mineralized layers in a multiple stacked conglomerate layer sequence in the Elsburg reefs of the Witwatersrand Rand System at the Target deposit. The method of categorization of resources according to confidence in the estimate is also explained. The feasibility processes carried out on the three-dimensional model, in accordance with the SAMREC code are also described. An example of the development of a reconciliation process utilizing chip sampling is also explained.

Jan 1, 2003

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By A. Amiel

Tarkwa Gold Mine is owned by Gold Fields Ghana, IAMGOLD and the Government of the Republic of Ghana in a 71%, 19% and 10% ratio. The mine is operated by Gold Fields Ghana. This large, low-grade, open pit, gold mining operation is located in Tarkwa, in the Western Region of Ghana, approximately 320 kilometres by road, west of Accra, the capital of Ghana, West Africa. In the Financial year ended June 2007, the operation mined a total of 108 million tons of which 22 million tons was ore. The mined ore is processed through three gyratory crushers supplying two heap leach pads (north and south) and a carbon-in-leach (CIL) plant. Before the 6 Sigma project commenced, the current fragmentation was resulting in sub-optimal feed size to these crushers. It was decided to use 6 Sigma methodology to improve the fragmentation. A defect was defined as a fragmentation analysis indicating less than 95% passing 750 mm. The objective was to improve fragmentation in order to achieve a constant throughput to the north heap leach crusher of 1500 t/h, a 5% increase in pit loading efficiency and a 50% decrease in rock breaker hours, equipment damage costs and in-pit sheeting costs respectively. However, this was not to be achieved at the expense of grade control as Tarkwa is exploiting a low grade, high volume deposit and therefore ore dilution must be kept to a minimum. This paper is intended to take the reader through the various 6 Sigma phases of the project (define?measure?analyse ?improve?control), which have resulted in a 10% reduction in loading times, of which half has been attributed to improved fragmentation, as well as a substantial increase in blasted stocks. The focus has been on both drilling and blasting parameters as both processes had to be taken into account. These parameters are technical but personnel factors were also identified and dealt with as they arose. In order to measure the impact of any change in the process parameters on the fragmentation size distribution, cameras have been acquired. One has been installed looking into the bowl of the north crusher and the other one was dedicated to field observation, of individual blasts. Both are used for ongoing fragmentation analysis. At Tarkwa, mining efficiency is strongly dependent on good fragmentation as well as the presence of unblasted ?toes? on the pit floors. Crusher throughput depends on an acceptable ore fragment size. Compliance with plan for actual hole depths was temporarily monitored by manual hole dipping, but this is now being replaced with a fully automated drill data management system developed by Sandvik and Modular Mining. The Six Sigma methodologies, using control charts based on data collected in the field, allowed the mine to improve methods for the control of blasted material. It also enforced the implementation of a quality control programme encompassing the entire drill and blast process.

Jan 1, 2008

By R. M. Franz

This paper considers potential risks to the health of workers in ultra-deep mines, including barotrauma, physiological effects and toxicity of airborne pollutants. Relevant previous research is reviewed, including work by the Chamber of Mines Research Organization and the Deep Mine Cooperative Research Programme, and recommendations are offered for prospectively limiting pressure-related health risks.

Jan 1, 2005

By F. T. Cawood

The distinction between real estate ownership and that of interests in the property is fundamental to the appraisal of mineral properties. This distinction affects the nature and understanding of security of tenure and, consequently, the perception of what constitutes fair value. Legal matters are a particular concern because of their influence on security of tenure, ownership definition and use restrictions. The dynamics of the market and the complex interrelationships between the factors of production define value at a specific point in time for the bundle of rights, interests and assets that constitute a mineral property. Because each mineral property is unique, physically immobile and of a wasting nature, its usefulness to its owner and society must be optimized. The US Appraisal Institute (2001) classified the forces that affect land use as the cultural, political and economic attitudes of society. These forces culminate in laws that often dictate the purposes for doing appraisals. Once the legal definition of the asset is understood, valuers can decide on the valuation process that will support the final valuation approach.

Jan 1, 2004

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By R. Degel

Keywords: Pyrometallurgy, DC furnaces, electric smelter, FeCr, FeNi, FeMn, Si metal, ferro-alloys, platinum production, circular furnace, energy recovery system In 1906, the first submerged-arc furnace was supplied by SMS Siemag. Since then, the division has become established in various industries such as ferro-alloys and non-ferrous metals, and in numerous other special applications. During the evolution of this technology, more efficient units with longer lifetimes were developed. Today, especially the potential of DC-based smelters, raises worldwide attention, with some projects having already started to implement this kind of technology. This paper evaluates SMS Siemag?s general viewpoint regarding the potential application of DC smelter technology and possible options for the ferro-alloy and non-ferrous industry. SMS Siemag is currently executing a FeCr project in Kazakhstan, where four of the world?s largest closed-type DC smelting furnaces, with a power input of 72 MW, will be installed. These furnaces include the latest technological features of modern DC smelters, which are described in this paper. SMS Siemag has started a long-term research and development project allowing a direct comparison of AC versus DC technology on a large scale, using a recently installed 1 MVA test furnace at the IME at the University of Aachen, in Germany. For open-type ferro-alloy and Si-metal furnaces, SMS Siemag has developed an energy recovery system, which is presented in this paper.

Jan 1, 2011

By R. Butcher

Mud rushes are hazardous occurrences that have occurred frequently in mines in South Africa, and have been the cause of numerous fatalities in the past. Mud rush incidents not associated with accidents are believed to be common occurrences that are not generally reported. Many such incidents are probably associated with the operation of chutes and box fronts. This paper describes the conditions necessary for mud rush occurrences, postulated mud rush mechanisms, and methods of combating the mud rush hazard.

Jan 1, 2005

By R. M. Kear

Strategic and tactical planning are both required in the mining industry but have completely different objectives and require different environments. If these are not fully understood, then the best value for a mining operation may not be realized. This paper examines the differences in these approaches and how they interface in the mining environment. The objectives, content, skills required and the implied management issues for these two components are examined with the hope that this will assist management and the planning teams in defining their respective roles and expectations. The opinions are those of the author based on his experience on several mining operations and projects.

Jan 1, 2006

By L. Bircumshaw

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) degree This paper details the formulation of a mathematical model for the simulation of a primary bioleach reactor, with specific reference to the leaching of pyrite. The model is based on the direct reaction mechanism, where the leaching of pyrite is said to occur via a two-step process. The process involves the formation of ferrous?iron through the chemical leaching of pyrite and subsequent bacterial oxidation of ferrous-iron back into ferric-iron. At steady state the rate of chemical leaching and bacterial oxidation are linked by the ratio of ferrous-iron to ferric-iron in solution. The extent of conversion of pyrite in the reactor system is described using the segregated flow model, with the exit age distribution of the solid phase being described by the Tanks-in-Series model. The final phase in model formulation involves the inclusion of steady state material balances on the bacteria and fluid phase components. The model is compared to pilot plant data and laboratory data for two different types of pyrite concentrates, with simulation results showing that the model is in good agreement with the data. Author key words: Bioleaching; pyrite; primary reactor; modeling; segregated-flow model; tanks-in series model.

Jan 1, 2006

By R. J. Kendall

As we enter the new millennium, the South African mining industry has to ensure that it becomes more competitive if it is to survive in the ever more demanding global environment. Traditionally, mechanization in narrow stopes has been limited to the use of scraper winches, and numerous mechanization attempts have been restricted to pilot projects operated on an extremely limited scale (with varying degrees of success). The benefits of hydropower are well documented, and Northam Platinum has shown these benefits to be achievable on a mine-wide basis. However, the equipment originally developed for hydropower systems has followed the traditional labour-intensive approach commonly used in deep level narrow stoping operations. The problems experienced with the hydropower system are discussed and the rationale for developing alternate technologies is explored. The hydropower system has shown to be a versatile powering medium which can be harnessed for a diversity of uses. It (hydropower) enables the mining engineer to change traditional paradigms and to design an entirely new approach for optimizing the mining operation based on explosive techniques. The system developed for Northam consists of the following: ?Purpose-built stope drill rig operated off the hydropower system with special features to ensure accurate drilling patterns throughout the length of the blast hole ?Purpose-built high rate cleaning system for rapid transfer of fractured ore to the stope orepass ?Redesigned stope layout to facilitate in-stope water control and to recover fines from the run-off water ?Purpose-built drill rig for rapid establishment of reef raises and advanced strike gullies ?Purpose-built drill rig for flat end development. On both types of development end rig, emphasis is placed on ensuring accurate drilling patterns throughout the length of the hole to maximize linear advance per blast. The paper discusses the implementation of the Northam system on a large scale as well as current initiatives to further improve on the efficiencies of mining operations. It concludes by emphasizing that mechanized hydropowered stope technologies are in their infancy and thus offer unlimited scope in progressing beyond today?s paradigms to present as yet unthought of solutions for optimizing deep level ore extraction.

Jan 1, 2000

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004