Search Documents

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

By Stephen C. Tadolini, Thomas M. Barczak

Western mines have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the early 1990’s provided a very effective alternative and remains the dominant form of tailgate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled together, provides more capacity than an equivalent sized Can support and improves transport efficiency. However, the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but they have not been proven in high deformation environments. Alternative supports are also being used in longwall recovery operations. These include the Rocprop and Omni Prop, which are extendable support systems. They also provide active roof loading which can be beneficial in these applications. Specialty supports, such as the Sand Prop and Spider Prop, have also been introduced into western longwall operations. This paper compares the performance characteristics of these various support systems.

By Gregory J. Chekan

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating multiple seam interactions associated with longwall mining. Longwall gate entry and panel stability have been influenced by previous mining in coalbeds above and below a mine in Virginia that operates in the Lower Banner Coalbed. Directly superjacent, approximately 115 ft, the Upper Banner Coalbed has been partially worked by room-and-pillar mining. Directly subjacent, approximately 730 ft, the Tiller Coalbed has been worked by partial room-and-pillar retreat mining. The study mine has experienced problems during development of gate entries in areas of overmining and undermining. It is anticipated that stress fields associated with adjacent mining may further affect gate entry stability and face advancement during the extraction of the longwall panel. To assess overmining and undermining effects on ground stability, the Bureau gathered geotechnical information at the site. Headgate entries and pillars were instrumented and monitored to study loading behavior as the longwall face approached and passed potential problem areas. Measurements indicate that although increases in average pillar pressure were greater than predicted values, previous mining in adjacent coalbeds had little effect on headgate stability.

Jan 1, 1989

By C. M. Frost

The hydrodesulfurization characteristics of a Venezuelan topped crude oil and a Venezuelan reduced crude oil were determined at temperatures from 740° to 850° F, pressures from 800 to 1,600 psig, and space velocities from 1.0 to 2.0 Vo/Vc/hr. Kinetic calculations showed that under these conditions the desulfurization reaction was first order with respect to sulfur and had an average activation energy of 32.5 kcal/mo1. Catalyst life tests made at 750° F, with pressures of 800, 1,200, and 1,600 psig and space velocities of 1.0 and 1.25 Vo/Ve/hr, showed that the decrease in the relative activity of the catalyst was a logarithmic function of time or volume of oil processed and the amount of vanadium deposited on the catalyst. Comparative tests made with residual fuels prepared from a Wilmington, Calif., crude oil and a Wyoming asphaltic crude oil showed that catalyst life may be extended by processing fuel oil with a low metal content, but it may be shortened by the presence of large amounts of asphalt in the feed.

Jan 1, 1971

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By Terry J. Close

The Gates of the Mountains Wilderness study area is underlain by intrusive and sedimentary rocks, mainly limestone. No limestone has been produced from the study area; suitable material is more readily available elsewhere. Small amounts of gold, sapphires, and corundum were produced from a placer deposit along the banks of the Missouri River. The remaining gravel contains low mineral values. Other alluvial deposits along the Missouri River and Beaver Creek contain no identified economic resources other than sand and gravel. Some deposits could provide suitable construction material for local use.

Jan 1, 1984

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By R. B. Schluter

The Bureau of Mines investigated the flotation responses of two copper-nickel ore samples from the Duluth Complex with the objective of recovering bulk sulfide concentrates. One of the ores studied was taken from a test pit; the other was taken from a test shaft. The samples were quite similar except that the pit sample analyzed 0.35 pct Cu and 0.11 pct Ni and the shaft sample analyzed 0.69 pct Cu and 0.14 pct Ni. Flotation responses were studied in both laboratory and pilot plant tests. Pilot plant flotation responses were similar for both samples resulting in grades of 12.2 pct Cu and 2.5 pct Ni for the pit sample and 12.2 pct Cu and 2.1 pct Ni for the shaft sample. Weight recoveries were 2.5 pct for the pit sample and 5.2 pct for the shaft sample. Copper and nickel recoveries for the pit sample were 87 and 62 pct, respectively, and 92 and 73 pct for the shaft sample. Both concentrates contained small but significant values of cobalt and precious metals. Cobalt recoveries were low--less than 40 pct for both concentrates. Precious metals contents of the concentrates were 1.59 oz/ton for the pit sample and 0.99 oz/ton for the shaft sample. Silver was the predominant precious metal by weight, but platinum and palladium represented the highest values.

Jan 1, 1980

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases. In the 1950's, the Chesapeake and Potomac Telephone Co. of West Virginia introduced a telephone set for use in explosive atmospheres that was designed around the philosophy of explosion containment. To contain an explosion within the telephone set required a 39-pound casing, which greatly limited portability. [ ] Both of these telephone sets required "pipe" or conduit, not a very practical item for a 100-squaremile coal mine. A common thread prevalent in the first 40 years of design and development is that the primary effort was placed on the telephone set. In the early 19701s, as work began on the design of modern communication systems for use in underground mine environments, the following requirements were established: 1. Must meet intrinsic safety standards .--This applies not only to coal mines, but to other explosive environments. 2. Must be compatible with the environment.--The system must with- stand dust, moisture, and corrosive conditions. 3. Must be rugged in structure.-- The system must withstand maintenance by 10-inch pliers and 4-pound hammers, as well as impact from a falling piece of roof. 4. Must be size-flexible.--Whatever is built must be sized for the small operator as well as the large companies. 5. Must be a total system in design.--The system must be intrinsically safe, including cable, power supply, and station set. 6. Must work with present telephone system.--The system should be compatible with aboveground communications already in place; it should not be the single cause of change in aboveground communications. 7. Value-added pricing.--The system should be reasonably priced so that savings created by its introduction will more than offset the installation cost.

Jan 1, 1984

By Arthur S. Swanson

The DuBois fluorite property in the southwestern part of Hardin County, Ill., has been active intermittently since 1904 and has produced an estimated total of 1,000 to 2,000 tons. The persistence of the vein and the stratigraphy suggested extensions of the ore body formerly mined. The Bureau of Mines investigated the property by core drilling early in 1944. Four holes were bored which totaled 1,106 feet and extended along a strike length of 1,150 feet. The data obtained in the course of the investigation are presented in this report.

Jan 1, 1948

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

By Ben A. Kornhauser

Petroleum production was the principal component of the mineral industry, followed by cement production and some salt output. The French Central Fund for Economics Cooperation loaned $9.15 million2 to the Communauté Electrique du Benin (CEB), which served Benin and Togo, toward financing the construction of a dam on the Mono River at Nangbeto, Togo. The dam was to supply hydroelectric power to reduce the energy dependence of the two countries and to irrigate crops. Nine other international financial organizations, including the International Bank for Reconstruction and Development (World Bank). the African Development Bank, the Arab Bank for African Economic Development, and the French Aid and Cooperation Fund, contributed to the estimated $140 million cost of the dam. The CEB also was to contribute to the financing. Contracts amounting to $60 million already had been awarded to West German and Canadian firms. The dam was expected to be completed in 1987.

Jan 1, 1986

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using empirical approaches previously developed. The Bureau of Mines assessed data collected from 16 longwall panels in the Northern Appalachian basin. Attention was focused on the effects of rock lithology, excavation width, and panel depth on the subsidence factor. The results show that the subsidence factor can be expressed in terms of the width-to-depth ratio by a simple exponential equation, which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site, and can be expressed in terms of percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

Provide a method for obtaining in situ measurements of coal cutting forces which are needed for mining machine design. Approach A portable in-seam testing device is carried to the face of an underground coal mine heading to measure the cut-ting force encountered by a continuous miner pick directly at its maximum depth of cut. How It Works The tester frame is attached directly to the coal surface with four one inch diameter threaded studs resin-bolted into 1-1/4 inch diameter holes which are drilled 30 inches deep. Spherical nuts and washers compensate for misalignment between the bolts bearing plate, and traverse beams. Spacers can be placed over the studs to assure that the traverse beams remain in the same plane. Cutting forces are applied by a hydraulic cylinder that moves the pick of the tester through a twin-chain arrangement which gives a 20-inch cutting stroke with

Jan 1, 1982

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992