Search Documents

By F. L. Wideman

Output of ore and waste from metal and nonmetal mines in the United States continued an upward trend and established a new high. The tonnage of ore handled increased 6 percent over that moved in 1964 and the tonnage of waste rose almost 10 percent. Earth moving by these two activities exceeded 3.2 billion tons, an increase of 7 percent over the 1964 total. Crude material from which metal or nonmetal products were derived continued to be about 75 percent of the total material handled. In 1965, surface mining methods were used to produce about 93 percent of the ore, 99 percent of the waste, and 95 percent of the total material handled. These percentages have remained almost constant since the beginning of this decade.

Jan 1, 1966

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

By Sumner M. Anderson

ATHOUGH scattered signs of increased activity in the mining industry accompanied an incipient improvement in the overall economic situation during the latter months of 1963, production levels for the year as a whole responded to the general 1962-63 business recession with a 4.2 percent decline. The petroleum industry, active since 1907, did not become a dynamic force in the economy until exploration and drilling contracts were concluded with private companies in 1958 and 1959; on November 15, 1963, having virtually achieved self-sufficiency in petroleum in the preceding year, those contracts were unilaterally annulled. In the field of metallics, the only approach to internal sufficiency-aside from the iron and steel industry that has depended heavily on the importing of basic raw materials-has been in mining, smelting, and refining lead and zinc although iron ore, silver, beryllium, tantalite, and tungsten have been mine production items of economic significance. Reserves of lead, zinc, silver, bismuth, vanadium, and low-grade and metallurgically difficult iron ore-as well as those of beryllium, tantalite, and tungsten which are produced primarily for export-appear to be fairly abundant. The exploration of deposits of copper, cobalt, tin, lithium, gold, manganese and uranium has been undertaken on a relatively small scale, and little precise information is available on the extent of reserves. Argentina is dependent on foreign sources for part of its required iron and steel and, except for lead and zinc, most of its nonferrous metals. Nonmetallies and solid fuels present an exceptionally varied array of production items among which cement had the second largest 1963 output in South America. Borates, bentonite, common clay, diatomite, fluorite, granite, lime, limestone, obsidian, onyx, rhodochrosite, salt, and spodumene ordinarily are produced for export either exclusively or in excess of domestic consumption requirements. Barite, cement, chalk, gypsum, marble, and mica are both exported and imported. Argentina depends entirely or partly on imports for coal and coke, certain special types of clay, mineral abrasives, graphite, magnesite, mineral fertilizers, sulfur, talc, and minerals for construction, the last group being chiefly attributable to convenience of river transport from Uruguay.

Jan 1, 1964

By R. Ward Stahl

Fire has been one of man's most useful tools through the ages and certainly is a "must" for industrial progress but when uncontrolled is one of the most destructive agencies. This fact is even more important in a coal mine, where many persons and much expensive equipment are confined in a relatively small area. Means of escape from a burning area, as well as from the products of combustion, are often limited; and in many instances the entire surroundings are combustible. Numerous mine fires, which resulted in a high death toll and great financial loss through the years, have caused mine owners to search for the best fire-fighting equipment; much of this has been installed, the quantity depending largely upon the experience of the individual companies or neighboring mines in certain coalfields. A mine owner or operator has meager published information on the actual fire protection afforded and systems of fire-fighting inaugurated in the coalfields, by which he could compare his efforts and get some idea of the adequacy of his own protection. To further general knowledge of the subject, it was decided to survey a representative number of mines in the field and show what has been accomplished. Representative mines were selected in various coal beds; some had similar tonnage, so comparison could be made if desired.

Jan 1, 1957

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state, Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the. fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds.

Jan 1, 1969

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U. S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992

By S. J. Davenport

[The tremendous increase in mine mechanization since 1929 has increased markedly the application of electric power in and about the coal mines of the United States. Cutting, drilling, and leading machines have replaced hand-mining methods in nary mines. As a result, expansion of the gathering haulage has necessitated introduction of extensive feeder, trolley, grid other power wires. (1)3/ In spite of this vast mechanization the fatality rate from electric shock has been on the decline. However, there are still too many accidents, and efforts to eliminate electrical hazards cannot be relaxed. It is hoped that an acquaintance with the physiological aspects of electrical accidents will make workers end management aware of the lurking dangers of this very common and extremely dangerous form of energy.]

Jan 1, 1951

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

By Ivan F. Avery

PRODUCTION of carbon black decreased 4 percent in 1961. Output in the major producing States of Texas and Louisiana decreased 1 percent and 8 percent, respectively. Production of channel black continued downward, declining 10 percent in 1961 compared with 9 percent in 1960. Furnace black production also decreased 3 percent from 1960. Total domestic sales, however, increased 2 percent, Sales to most major consumers increased, but sales to the ink industry decreased 10 percent. Producer's stocks decreased 5,083,000 pounds during the year. Exports decreased 4 percent. SCOPE OF REPORT Carbon black is a very pure grade of quasi-graphitic carbon; particle diameters range from 50 to 5,000 angstrom units. Annual reports were submitted to the Bureau of Mines by operators of all commercial plants in the United States.

Jan 1, 1962

By Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

A fundamental safety research area for the National Institute for Occupational Safety and Health (NIOSH) is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach is to develop and evaluate new and innovative seal designs that provide increased explosion protection for mining personnel. The NIOSH Pittsburgh Research Laboratory (PRL) cooperated with HeiTech Corp. of Virginia, Barclay Mowlem Construction Ltd. of Queensland, Australia, and the Mine Safety and Health Administration (MSHA) in three separate research programs to evaluate the strength characteristics and air leakage resistance of numerous innovative seal designs and ventilation control structures for use in underground coal mines. For each phase of the program, various full-scale seals, stoppings, and an overcast design were constructed in PRL's Lake Lynn Experimental Mine near Fairchance, Fayette County, PA. The seals and stoppings were built in crosscuts and were subjected to explosions to evaluate their strengths. Four pumpable cementitious seal designs ranging in thickness from 610 to 915 mm (24 to 36 in) were evaluated in the first cost-reimbursable research program with HeiTech Corp. A simple wooden framework with brattice liner was used as a form to contain the cementitious slurry during the curing period. As the seal designs decreased in thickness, higher compressive strength cementitious grout was used. All four seals withstood an explosion pressure pulse of at least 138 kPa (20 psi) while maintaining acceptable air leakage resistance. In the second cost-reimbursable research program with Barclay Mowlem Construction Ltd. of Australia, several innovative seal and stopping designs and an overcast design were evaluated. Each of the seal designs and the overcast side and wing walls used one or more air-inflated vinyl bladder assemblies anchored to the mine roof and hitched into the ribs and floor. The air within these bladders was displaced with a high-strength cementitious grout. The overcast deck consisted of a 200-mm ('7.8-in) thick reinforced cementitious slab. This was the first time that an overcast structure had been explosion tested under full-scale conditions. All of the seals, stoppings, and overcast design passed the air leakage tests before being subjected to a series of explosions with static pressure pulses ranging from 14 to 475 kPa (2 tab 69 psi). Instrumentation measured seal and overcast wall displacement as a function of time. The 450-mm (1 7.7-in) thick seal in the 2.8-m(9-ft) high third crosscut withstood an explosion pressure of 170 kPa (25 psi), but failed during a later test, which generated a peak static pressure of 475 kPa (69 psi) at the seal location. A similar 450-mm-thick seal in the 2.1-m (7-ft) high second crosscut withstood three explosion tests, which generated peak static pressures of 195, 205, and 370 kPa (28, 30, and 54 psi) at the seal location. Next, the overcast design withstood four explosions, which generated static overpressures ranging from 16 to 47 kPa (2.3 to 6.8 psi). A third program at the request of MSHA evaluated the effectiveness of using pressurized grout bags (Packsetter bags) along the mine roof and ribs in lieu of floor and rib hitching for a standard-type solid- concrete-block seal. This program was initiated to address an urlusual geological mining condition encountered when building seals in entries where required rib hitching is not a viable option due to soft friable coal. Results showed that the use of these quick-setting grout-filled Packsetter bags pressurized internally to 300 kPa (44 psi) not only provides a seal that can withstand a 138-kPa static pressure explosion, but also provides a sealing option where rib hitching is not possible.

Jan 1, 2003

By H. K. Kutter

The pressure pulse generated by an underwater spark \vas investigated in relation to its potential use for rock fragmentation. The study established (1) the relation between the peak discharge current and the peak wave pressure; (2) the relationships among the peak wave pressure, the discharge voltage, and the spark gap width; (3) the type and pulse duration of the generated wave; (4) the percentage of energy transmitted in the spark as a function of spark gap width and discharge voltage; and (5) the percentage of energy converted into the pressure wave as a function of gap width and discharge voltage. Spark-generated fractures were studied in two-and three-dimensional rock and plastic specimens. The laboratory results indicated that the pressure pulse generated by an underwater spark is a potential practical tool for rock fragmentation. The paper contains an appendix describing the capacitive pressure gage specially developed for the laboratory tests.

Jan 1, 1969

By A. Gene Collins

During recent years the interest in trace and minor constituents of oil-field water, petroleum, and their associated reservoir rocks has increased. The metals copper, nickel, lead, manganese, iron, zinc, and cadmium are not determined routinely in oilfield brine analyses. Determination of these metals and subsequent correlation of these data should yield information to aid 1n the interpretation of the origin of different waters. The methods of analyzing oilfield waters have several potential applications: (1) Aiding in the search for petroleum; (2) identifying sources of intrusive brines; (3) controlling corrosion; (4) controlling produced water; increasing knowledge of the geology of subsurface formations; (5) identifying incompatible waters in waterflooding operations; (6) increasing the knowledge of the flow of oil, gas, and water in underground formations; and (7) aiding in the identification and location of valuable mineral reserves. Some brines contain enough valuable minerals to be recovered commercially.

Jan 1, 1962

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990