Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D.2 Principal Types of Coating A Sodium Silicate Sodium silicate is a good fire retarder when freshly applied, but it loses its effectiveness if the relative humidity is at all high, thus exposure to a relative humidity exceeding 65 percent causes a serious decrease in the effectiveness after only one month. In fire, sodium silicate swells to a frothy mass (intumescence) which hardens and insulates the wood against heat. This property is destroyed by exposure to moisture. Manufacturers of many of the proprietary paints containing silicates state that their products have overcome this difficulty The reagent may be applied alone, or, better, in a mixture with lime-water and common salt, or with inert fillers such as kaolin or asbestos. B Ammonium Phosphate Strong solutions (25 to 35 percent) of monammonium phosphate or diammonium phosphate give good protection. Two or three coats of hot solution should be applied either with a large flat brush or an ordinary paint spray gun The solution should be applied as hot as possible, as this improved penetration, and it should be the aim of the operator to apply 4 lbs of reagent, i e , one gallon of 33 percent solution to every 100 square feet of surface

Jan 1, 1976

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence coefficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculation methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By N. W. Lord

This volume contains the descriptions of the samples whose analy- ses are published in the preceding volume, Part I of this bulletin. The descriptions have been compiled from the notebooks of the per- sons who collected the samples, have been condensed from accounts given in published reports of the United States Geological Survey, or have been furnished by the collectors themselves. Inasmuch as the descriptions represent the work of many persons during a period of six years, and inasmuch as they were recorded under widely differing conditions, they necessarily vary in fullness of detail. The descriptions are published for two purposes: (1) To prosent such information regarding the character of the coal, the impurities in the beds sampled, and the nature of the roof and the floor of the beds as has a definite bearing on the significance of the analyses of the samples, and (2) to give any supplementary details such as the capacity or the output of a mine, the method of mining and prepar- ing the coal, and the chief uses to which it is put, that may be of assistance to Government engineers or purchasing agents, and to other persons, in preparing specifications and awarding contracts for fuel.

Jan 1, 1913

By Maria I. De Rosa

Coal mine fires pose a constant danger to the safety of miners and to their livelihood. Underground mine fires pose an added hazard because of the confined environment with remote exits. Enactment of safety regulations [30 CFR2 75 and 771 for under- ground coal mines and surface coal operations has greatly improved the safety of miners. However, mine fires and fire injuries remain serious hazards for all coal mining operations. This report analyzes mine fires and fire injuries for all U.S. coal mining categories (underground coal mines, surface of underground coal mines, surface coal mines, and coal preparation plants) during 1990-1999. Fires involving contractors are also included in the analysis. Similar analyses (for underground coal mines only) by the former U.S. Bureau of Mines (USBM) were reported by McDonald and Pornroy [I9801 and Pornroy and Carigiet [I9951 for 1950-1977 and 1978-1992, respectively. For comparison purposes, data for 1978-1 992 are mentioned in the "Underground Coal Mine Fires" section of this report. Detailed analyses of mobile equipment fires for all underground and surface coal and metal/nonmetal mining categories during 1990-1999 have recently been reported by NIOSH [De Rosa 20041. Risk rate values (fire and injury risk rates) for the 10-year period (1990-1999) and for five successive 2-year periods within the 10-year period are derived. Risk rate values for individual states for the 10-year period are also derived. Other variables by state and time period include employees&apos; working hours, lost workdays, and coal production (underground and surface coal mines only). The number of fire fatalities is reported by time period. Variables such as ignition source, method of detection and suppression, equipment involved, location, and burning material are reported by five 2-year periods only. Furthermore, the number of fire injuries per number of fires causing injuries and total fires has been analyzed by year, ignition source, equipment involved, and location. For comparison purposes, the major fire and fire injury findings for all coal mining categories have been reported. The data in this report were derived from "Injury Experience in Coal Mining" [MSHA 1991a, 1992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001, "Fire Accident Reports" [MSHA 199 1 b,c; 1994b; 1995b,c; 1998a,c,d,e,f; 1999a,b,d,e], MSHA "Fire Accident Abstracts" internal publications, and verbal communications with mine personnel. Mining companies are required by 30 CFR 50 to report to MSHA all fires that result in injuries and fires that are not extinguished within 30 min of discovery. A small number of fires lasting <30 min without injuries reported in the "Fire Accident Abstracts" have been included in this report. The analysis in this report will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the causes and hazards of mine fires and fire injuries. It will also form a basis for developing future fire research programs.

Jan 1, 2004

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For gold, silver, copper, lead, zinc, and tin, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal.

Jan 1, 1981

Reduce the cost and incidence of low-back pain in underground coal mines through redesign of materials-handling tasks. Background Approximately 25 pct of all injuries in mining involve trauma to the hack. These injuries account for at least 30-40 pct of worker compensation payments made by the industry, are the leading cause of lost work days in mining, and have been estimated to cost the industry $50 million annually. It is clear that the traditional approach to reduce back injuries (i.e., training) has been largely ineffective. Thus, new approaches are necessary to control this problem. This document briefly describes methods that can be used to redesign hazardous materials-handling tasks to reduce the threat of worker injury. Approach A model for redesigning materials-handling tasks is shown in figure 1. The model outlines the sequence of steps that should be followed (and questions that should be asked) when developing new strategies for handling materials in underground coal mines. A critical examination of the current supply-handling system is the first step to developing safer materials-handling procedures. The purpose is to identify hazardous tasks that can be modified to reduce injury risk. Accident analysis (a review of past accident records) and task analy¬sis (usually a videotaped analysis of hazardous jobs or tasks) arc effective methods of distinguishing areas where job redesign is needed.

Jan 1, 1992

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I describes an underground bituminous coal mine operation in a 48 inch seam, with an estimated production rate of 1,056,000 tons per year. The system includes four continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. This section illustrates the input data sequence and the various report formats which may be selected for the printing of results. As explained earlier, at the present time, the elements of the Cost Data Library must be read in with the regular data input. Thus, in the input data listing, immediately following the required user input, are cards which contain the inputs of the cost library. Examination of the cost reports indicate the absence of cost values for some categories for which the system would normally be expected to incur costs. This situation has arisen due to the format of the cost data provided in the U. S. Bureau of Mines reports. An example of this is the charge of $20/ton for brattice cloth while no charge is indicated for stoppings. The test report data provided a single figure for ventilation cost without a supplemental breakdown. Thus the cost indicated for brattice cloth is actually the total ventilation cost. These explanations hold true for the data input and output for Test II, Appendix III.

Jan 1, 1975

By C. B. Manula, R. L. Sanford, R. A. Rivell

Development of the Rail-Haulage Sub-assembly for the Production Sub-system (UGMHS)* required the use of ,a newly formulated model in order to best satisfy the requirements. Many of the ideas of the former single-stage rail simulator included in the original version of UGMHS have been used, together with the results of experience gained in applying the earlier model to a variety of operating situations (Sanford, 1969). The sub-assembly is developed as an independent system and, as such, can be used to analyze track systems using production distri¬butions as data input. In addition, since this model is designed to replace the original sub-assembly in UGMHS, the linking procedure is identical with respect to bi-directional information flow. The flow of coal from production sections, for example, fills the mine cars, but a condition of "out of empties" or "full of loaded" at a loading station will shut down inby production sections. A requirements analysis was conducted to determine specifically how the model could best serve the user. Operating management had the largest input in developing the following requirements for the Rail Sub-assembly: a) data input in mixed narrative - numeric form to permit user identification of the input variables; b) a user option to extract several ranges of detail in model output, i.e., an average shift summary of minimum retrieval

Jan 1, 1974

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Network analysis of mine ventilation systems is not new, having been traced back to 1854. A Committee Report (1970) has also reported the extensive work done in this respect in the United Kingdom, Japan, U.S.S.R., South Africa, United States, and other countries. Wang, et al (1970) developed a computer program which is an improvement over the earlier one developed by Wang et al (1967). The program has been recently modified and extended to include methane emission features by Owili-Eger (1973). This computer program incorporates all the novel features of the earlier programs. These include the capabilities of mesh selection, free splitting, internal or external fans, natural ventilation pressure and fixed quantity branches. The program is written in Fortran IV and, in effect, is an experimental mine in which many ideas can be tried out. The computer produces, besides the input data and certain computational data, the quantities and head losses in the branches, the head losses to be adjusted in the fixed quantity branches and the fan operating point. The last named program, hereafter to be referred to as the PSU/MVS, is presented in Appendix I. The application of this program is demonstrated in this manual through a series of selected examples. Application of the methane generator program is not included here as a detailed report on the subject is available elsewhere (Ramani et al, 1975).

Jan 1, 1975

By Lloyd A. Morley, Alan M. Christman

Presented below is a review of how the objectives, as outlined in the statement of the problem, were achieved. 1. Methods of evaluating the performance of grounding systems must be described. These methods are the subject of Chapter III. 2. Field trips to operating mines should be undertaken, and a cri¬tique of their grounding systems made upon the basis of obser¬vation and the application of the above techniques. An analysis of field trip data, along with practical recommendations, is in¬cluded in Chapter IV, while a complete review of all field trips is given in Appendix I. 3. Because of their thoroughness, present coal mine regulations should be evaluated, and their applicability to open-pit environ¬ments appraised. This has been done in consultation with governmental agency, manufacturing, operating mine, and consult¬ing engineers. As stated in Chapter IV, insight gained through field observations has served to amplify and extend the base of knowledge from which the recommendations were made. 4. The results of these investigations should lead to suggested Federal standards. Such recommendations comprise Appendix II. In addition, several important factors, which are discussed in Chapter IV, were brought to light as a direct result of the field research. 5. Seasonal variations in the earth resistance of ground mats, as illustrated by Table 12, reinforce the need for periodic

Jan 1, 1976

To reduce operator exposure to noise from vibrating screens at coal preparation plants. Background Hearing loss is one of the most common occupational illnesses in the United States. In the U.S. mining industry, hearing loss is 2.5 to 3 times greater than what is expected for the average population that is not exposed to occupational noise. Furthermore, studies by the National Institute for Occupational Safety and Health (NIOSH) showed that by age 50, 90% of coal miners have a hearing impairment versus only 10% of the population that is not exposed to occupational noise. A NIOSH cross-sectional survey of coal preparation plants showed that 43.5% of employees were overexposed to noise. The study also found that vibrating screens were one of the top five loudest types of equipment at these plants?as well as the most numerous?making them a key noise source to address.

Nov 1, 2009

By W. N. Poundstone, W. M. Merritts, B. A. Light

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining. This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g,.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes. In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased. Tests indicated that methane and water infused in bleeder holes traveled along the bedding planes of the Pittsburgh coalbed at a faster rate than across the planes. Methane associated with coalbeds is produced by the slow decomposition of carbonaceous material in the absence of air and the presence of water. It is lighter than air and, depending on its concentration, forms an inflammable or explosive mixture with air. It is believed that methane is entrapped in and around the pores of the coal and adjacent strata--often under great pressure. In many cases where the strata have been disturbed by geologic movements the

Jan 1, 1962

By Paul S. Lewis

The Bureau of Mines hydrogenated coals of different rank that had been irradiated with either x-rays or gamma rays. Lignite, high-volatile A and C bituminous, and low-volatile bituminous coals were exposed to l billion roent¬gens of gamma-ray radiation; specimens of high-volatile A and C bituminous coals from other sources received 6 million roentgens of X-ray radiation. Irradiated and unirradiated control specimens of those coals were hydrogenated in autoclave experiments at (6,000-p.s.i. final pressure and 400° C. with retention times of 15, 30, or 60 minutes depending on the coal rank and catalytic treatment. Comparison of results from irradiated specimens with those from the control experiments showed that the radiation had no beneficial effect on the coal. High-volatile C bituminous coal may have been affected by radiation more than the other coals. One billion roentgens appeared to reduce the amount of coal converted to liquids and gases by about 10 pct., and 6 million roentgens reduced it by about 6 pct. then catalyzed with tin. In all other cases, the conversion of irradiated coal was either reduced by as much as 4 pct. or was essentially the sank as that obtained with unirradiated coal. Irradiation during hydrogenation nay be effective for increasing the reactivity of coal and should be investigated; further work with coals irradiated prier to hydrogenation is not recommended.

Jan 1, 1962

By Nicholas Kyriazi

Significant portions of the present Federal regulations for certification of closed-circuit breathing apparatus (42 CFR 84) are not quantitative. The human-subject testing portion of the regulations specifies activities rather than metabolic work rates; however, heavy human subjects have higher oxygen consumption, CO2 production, and ventilation rates than lighter human subjects performing the same activities. This means that apparatus certified using different human subjects have effectively passed different tests. In addition, apparatus performance is monitored only during selected intervals of testing, and always during rest, rather than during the entire performance period. Further, testing is arbitrarily terminated at specific rated durations, leaving unknown the performance during the remaining duration. Duration itself is misleading to users who believe that the apparatus will last a certain time no matter how much they weigh or how hard they work. The actual duration obtained from an apparatus, however, is highly variable, being inversely proportional to the work rate at which it is used. In this report, recommendations are made to (1) replace the present regulations for certification of closed-circuit breathing apparatus with quantitative tests specifying metabolic work rate rather than activity,(2) continuously monitor relevant physiological stressors, (3) continue testing until exhaustion of the oxygen source, and (4) classify closed-circuit breathing apparatus by quantity of usable oxygen, i.e., capacity, rather than by duration. Physiology-based stressor levels are suggested as well.

Jan 1, 1999

By M. D. Schlesinger

As part of the development of processes for producing synthetic fuels from coal, the Bureau of Mines prepared a special jet fuel in a pilot plant for evaluation by the Air Force. This jet fuel had all the required physical properties, including the important specifications of high heating value and high density. However, the finished fuel did not pass the stability test specified by the Air Force and conducted by the Southwest Research Institute in a high-temperature research coker. The cause for this instability is being investigated because pure compounds of the type identified in this fuel are known to be stable. The tar acid oil used was a 230° to 300° C. fraction of low-temperature tar obtained by carbonization of a West Virginia bituminous coal in the pilot plant of the Consolidation Coal Co. Both the desulfurization at 400° C. and saturation at 300" C. were done in the vapor phase at 2,500 p.s.i.g. After catalytic treatment and distillation the final jet fuel had a boiling range of 194° to 247° C., a net heating value of 18,420 B.t.u./lb. and a specific gravity of 0.8463 60° F./60° F. It also had u pour point below -62° C., and at 0° C. its viscosity was 4.5 cs. The oil was virtually all bicyclic, 41 pct. noncondensed and 56 pct. condensed.

Jan 1, 1961

By A. R. Mumford

The fuel economy ot a. plant m be better than ite anxious friend.a J'ealize. A watchful a-aper1.ntend.ent of a Goverment plant, kn.owing that improvements in plant equipment bad. been made since hie atOkel'e were installed, was almosi per­ suaded to aubatitute a new t.,pe. The Bul'eau. of Mines was asked to aaoertain the a.cti.i&l performance ot the old stokera and tound. the plant alr doing from three to five per cent better than was promieed for the new egp.ipment. Tbe va.1.ue ot accurate knowledge of plant perfoimarice, am the need. ot eqm.pment to weigh and measure quantities is thus demonstrated. The boiler and ,tour ett1c1enc, was found to be 75 per cent, and the overall efficiency of the boiler, etoker• and economize, wae 78 per cent. Both records are high, and are to be attributed to ce in operation, to good working condition of the plant, and to the low rate ot evaporation, which was only aboui two-third., et the botler'e rated. capacity. The plant teated conaiated ot two la.boock & Wilcox boiler, tired b1 means of over teed 1toker1 and equipped wi t,b. a fuel economiaei- 1n the uptake. The bo1lel'a ,upplied ateam to two large water pump being used only intermittently.

Jul 1, 1922

By Dean H. Ambrose

This paper presents a technique for representing and analyzing random motions and hazardous events in a computer simulated three-dimensional workplace, providing machine designers and safety analysts with a new technique to evaluate ways to reduce operator-machine interaction hazards. Technical data in this paper is based upon a project striving to reduce workers&apos; risks from being hit by underground mining machinery in a confined space. By simulating motions of an operator&apos;s random behavior and a machine&apos;s appendage, researchers can accurately identify hazards, and use that information to form safe designs for mining equipment appendage velocity. Validating the model provided improvements in the operator&apos;s optimal viewing area, work task- starting positions, and operator&apos;s motions for a more accurate random behavior. Preliminary simulation results provided (1) an interesting approach to research data gathering in that there was no need for live subjects and test sites and costs associated with experiments become insignificant and (2) that the model was versatile by showing it was capable of accurately mimicking the range collision forces versus speed, operators&apos; size, and risk behaviors found in actual industrial situations and showed (I) that response time significantly affects the number of collisions experienced by the virtual subject and (2) that analysts must be discerning with the model and not read more From the databases than what the simulation model was designed to deliver. Keywords: random human-motion, anthropomebics model, machine-operator hazards, mine safety

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By C. B. Manula, R. L. Sanford, R. A. Rivell

A generalized flow diagram is presented in Figure 1, which shows the relationship of major model functions. This chart does not necessarily represent the anatomy of the computer program, but is designed to illustrate the informational interchange between major model functions. The related flow-charts-and computer program are listed in Parts I and II, Appendix A, respectively. Mine Car Stations The mine car stations are the activity centers for the model. The locomotive logic structure is designed to provide these stations with adequate cars and to clear them of car buildup. The model is designed to simulate a three stage haulage situation which suggests the need to differentiate station levels by type numbers. These are: a) TYPE 1 stations - mine cars are loaded here; b) TYPE 2 stations - intermediate stop and storage for mine cars; c) TYPE 3 stations - all mine cars that are stored here leave mine; and d) TYPE 4 stations - mine portal. TYPES 1, 2, and 3 have all loaded cars assigned to an ascending TYPE as their next destination. In input, if single stage haulage is designated, TYPES 1 and 3 do not exist, and if two stage haulage is called for, TYPES 2 and 3 are absent. A motor is not permitted to exchange cars between stations of the same type. Station Status Update. One major model function is to continuously evaluate the status of each mine car station. The major evaluations

Jan 1, 1974

By Lloyd A. Morley, Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in/which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-roof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges. Explosion-proof enclosure techniques have been utilized in U.S.

Jan 1, 1974