Search Documents

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952

By George H. Holmes

This paper , which describes mining methods and milling and manufacturing operations at the gypsum property of the Blue Diamond Corp. , is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . The property comprises about 4,000 acres and is in secs . 30 , 31 , 32 , and 33 , T. 21 S. , R. 59 E. , and secs . 5 , 6, 7 , 8 , and 9 , T. 22 S. , R. 59 E. , M. D. B. and M. , Clark County , Nev . , approximately 23 miles by paved highway southwest of Las Vegas , Nev . ( fig . 1 ) . This circular summarizes the history of company operations , describes physical features , labor and living conditions , and the geology . The method of exploration is outlined , and the section on mining methods contains descriptions of open - pit and underground systems , including loading and transportation methods . The crushing plant and tramway are described , as well as plaster-mill and board -plant practices . The boiler plant and organization are described , and wage scales are contained in the concluding section of the circular .

Mar 1, 1950

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10'6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By Harold C. Pierce

"INTRODUCTION During the years 1941 to 1945, the United States produced less than one-half of one percent of all primary nickel, whereas the nation's consumption of the metal amounted to nearly three-fourths of the world's supply. Although postwar nickel consumption probably will be less than wartime consumption, trade- estimates for the next 10 years are well above the average established during the 1930-1940 decade. The greatest consumption is expected in nickel alloys, particularly nickel-alloy steels. 3/ The greater use of nickel cast irons and nickel-clad metals also signifies an expanding nickel market. In anticipation of the postwar demand for nickel, and realizing the seriousness of the ""have not"" position of the United States with respect to this metal, the Bureau of Mines, sent an engineer 4/ into the lower Copper River region of Alaska during the summer of 1944 to investigate the nickel deposits near the head of Canyon Creek. Samples from the Spirit Mountain nickel prospect were sufficiently encouraging to justify more intensive exploration. As a result, a program of surface trenching, systematic sampling, and detailed mapping of the property was adopted and directed by a Bureau of Mines engineer 5/ in the summer of 1945."

Aug 1, 1946

By A. L. Engel

As a part of the program of the Rare and. Precious Metals Experiment Station, Reno, Nev., in connection with investigations of treatment methods for precious and precious-base metal ores, to further conservation and recovery of precious and base metals, tests Were made on samples from the Buzzard Mine, located in the vicinity of Placerville, Calif. These samples represented ore exposed during previous development work, in tunnels and a shaft on the property, including highly oxidized material from the surface zone and sulfide ores from depths of 150 to 300 feet. The surface samples contained little base metal and only enough gold 80 that economic exploitation of them would depend on development of a large tonnage of ore, low-cost mining methods, and satisfactory treatment methods. The sulfide samples were valuable enough to warrant further exploration and development and, if present in suitable tonnage, the installation of a treatment plant for recovery of both precious and base metals. The oxidized surface-zone samples carried 0.11 to 0.14 ounce gold per ton. Standard amalgamation and flotation tests of these samples gave low recoveries. Standard cyanidation tests indicated high consumption of lime and cyanide and gold extraction of 79.4 and 82.7 percent. Water-leaching the ore after crushing to minus 10-mesh improved cyanidation considerably. Ex-tractions of 82.7 to 85.8 percent were obtainec1 with lime consumption of 6 to 7 pounds per ton of ore and cyanide consumptions of 1 to 4 pounds. Grinding the samples to minus 200-mesh followed by water-leaching and cyanidation gave improved extractions of 91-92 percent of the gold, but with slightly increased consumptions of lime and cyanide.

Jan 1, 1949

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

By R. K. Conrad

The Bureau of Mines conducted corrosion research to determine suitable construction materials for geothermal resource recovery plants. Weight loss, pitting and crevice corrosion, U-bend stress corrosion, and electrochemical polarization measurements were made on selected metals in brine and steam process environments produced from high-enthalpy hypersaline brine from geothermal well Magmamax No. 1 at the Salton Sea Known Geothermal Resources Area, Imperial Valley, Calif. Cadmium (and by extension cadmium coatings) and a 6061-T6 aluminum alloy were unsatisfactory because of high general corrosion rates and, in the case of aluminum, severe pitting Molybdenum and niobium (columbium) were resistant to general corrosion, pitting, and crevice corrosion, Copper alloys corroded at rates that may preclude their use in wellhead brine, The presence of iron accelerated the corrosion of the copper alloys Titanium alloys were resistant to general corrosion and stress corrosion cracking in all of the environments. They exhibited crevice corrosion in some of the brine and steam environments and Ti6A14V pitted in the brine environments. They exhibited passive behavior over a broad range of potentials. Exposure tests were conducted on a high-temperature polyphenylene sulfide thermoplastic (Ryton) in the same environments. A 40-pct-graphite fiber-reinforced Ryton composite deteriorated readily in wellhead brine and failed in all of the brine and steam process environments; Ryton coatings on 316L stainless steel were adherent and performed well.

Jan 1, 1983

By Thomas V. Falkie, R. Venkataramani

The method of analysis was to test a large model containing potentially significant variables and on the basis of the results obtained, to reduce the model to one containing only the essential significant variables. This stepwise procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Data Preparation A majority of the variables measured were continuous over a specific range of values; for example, the variable "Width Ratio" varied in practice from 0.25 to 1.00. However, "dummy" values were assigned to certain operational variables in order that these varia¬bles would have numerical expression. The following variables were described in this manner. Variable "Dummy" Value x3: Development/Pillaring 0, if pillar extraction was being done 1, if development mining was being done x4: Boxcut/Open Cut 0, if a box cut was being made 1, if an open cut was being made The variables under consideration are represented symbolically as follows: Y: Loading rate (tons per minuts): TONS/MIN x1: Ratio, width of cut/width of cutter: WDRATIO x2: Ratio, height of cut/diameter of cutter: HTRATIO x3: Development or pillaring: D/P

Jan 1, 1972

By Walter K. Utt

The U.S. Bureau of Mines conducted research to develop an accurate, real-time, position monitoring and warning system for the vehicles used in surface mining. The product of this research will be technology to reduce accidents and injuries associated with the operation of surface mining haulage equipment. The position monitoring system should reduce accidents related to vehicle position and also increase the efficiency of haulage operations. This research was conducted in preparation for development of an accurate, real-time position monitoring and warning system, which notifies equipment operators when they deviate from a known safe course and are approaching a fixed hazard. A radar positioning system designed for marine applications was evaluated and a series of tests was run to determine the accuracy of the radar positioning system when used in a land vehicle. The radar position determination was compared to surveyed values. Both static and dynamic (moving vehicle) tests were conducted. The static test results were marginal and the dynamic test results were not accurate enough for the position monitoring and warning system. Although a promising technology, the system tested needs to be modified to meet the accuracy requirements of mobile mine equipment.

Jan 1, 2010

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Safety in Mines Research Board of the Mines Department for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, Great Britain, for arranging visits to mines in Great Britain, Belgium, Germany, and France. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in Great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy mine atmospheres which might, through neglect or accident surround the equipment. The means used by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers of American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. This paper presents the second of these surveys, which covers conditions in Belgium.

Jan 1, 1929

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By Harry W. Campbell

U.S. Bureau of Mines investigation; identified no mineral resources or evidence of mining activity in the Sheep Divide RARE II area. A deposit 10 mi (16 km) southwest of the area contains copper and silver minerals in the Triassic Wild Sheep Creek Formation which probably underlies basalt lava flows covering the study area. Abundant basalt in the area can be crushed and used as aggregate, but suitable deposits closer to markets are widely available No sand, gravel, coal, oil, gas, or geothermal resource, were Identified. INTRODUCTION Location and Access The Sheep Divide RARE II area [10 mi (16 km) west of the Snake River] encompasses 7,100 acres (2,800 ha) of the Hells Canyon National Recreation Area in the Wallowa-Whitman National Forest. Enterprise, Oregon, is located 23 air mi (37 (m) west of the area. Peripheral access is provided by the highway from Joseph to the community of Imnaha, Oregon, then south to the study area by the graveled Upper Imnaha Road (fig. 1).

Jan 1, 1983

By J. Douglas Causey

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 7,940-acre Southern Otay Mountain Wilderness Study Area (CA-060-029), and the 5,750-acre Western Otay Mountain Wilderness Study Area (CA-060-028) in order to evaluate their mineral resources. The wilderness study areas are located in San Diego County, CA, about 20 miles southeast of San Diego. No mineral resources were identified in the Southern or Western Otay Mountain Wilderness Study Areas, based on literature, field observations, and sample results. The wilderness study areas are underlain by a complex blend of Late Jurassic, moderately metamorphosed sedimentary and volcanic rocks. Evidence of mineralization is not obvious.

Jan 1, 1987

By Hewitt Wilson

[ ]

Jan 1, 1927

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

By Robert H. Dickson

This paper describing the mining practices at the Verde Central mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods and costs in various mining districts of the United States. ACKNOWLEDMENTS The costs contained in this paper were prepared by R. J, Huddleston, chief clerk, Verde Central Mines, Inc.

Jan 1, 1931

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By John H. Soulé

"INTRODUCTION The property of the Silver Spot Mines Co. is in the Boston Hill area within and adjacent to the southwest corner of Silver City, N. Mex. The area was visited by Bureau of Mines engineers 3/ in 1941 and 1942 during the investigation of possible sources of manganese. The area was visited again in November 1944 4/ to study the possibilities of geophysical exploration of the manganiferous-iron deposits. This geophysical work was performed in 1945 5/, confirmed the existence of known deposits of manganiferous-iron ores, and indicated the probable extent and situation of others.The Silver Spot property was churn-drilled from 1926 to 1929 during exploration for manganiferous-iron ores. The sludges from a number of the holes indicated low-grade lead-zinc mineralization. Lead and zinc minerals also were found on the dumps of some of the old shafts when the property was visited by D. H. Mullen, an engineer of the Bureau of Mines late in 1946. A diamond-drilling project was proposed. It was started in April 1947 with the intention of investigating the best of the known ore indications as shown by the old churn-drill holes and thus gathering new data upon which to base future work. Only one hole was drilled before the project was terminated because of lack of funds and time."

Mar 1, 1948