Search Documents

By A. J. Kraemer

[A great deal of interest has been manifested in the question of sulphur in fuels for automobile engines. Many different opinions have been expressed with respect to the effect of sulphur in gasoline on engine wear and engine performance. A wide difference of opinion exists as to the permissible limit of sulphur content for satisfactory operation.]

Jan 1, 1927

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By X. Shi, V. Vallyathan, N. S. Dalai

"Using. ESR spin trapping methodology, evidence was obtained that fresh quartz dust in a cell-free aqueous medium generated hydroxyl - and possibly superoxide radicals. The hydroxyl radical generation potential decreases on storing of fresh quartz dust in ambient air and on the addition of either catalase, superoxide dismutase, desferoxamine, or DMSO. The role of quartz related radicals in the biochemical mechanism of acute silicosis is suggested from these findings.IntroductionThis report summarizes our electron spin resonance (ESR) detection of oxygenated radical formation by freshly crushed quartz particles in a cell-free aqueous medium, and its inihibition by radical scavengers. This study was undertaken with to elucidate the primary biochemical mechanism involved in the development of silicosis (Farber, 1983; Reiser and Last, 1979; Silicosis and Silicate Disease Committee, 1988). In particular the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood (Farber. 1983; Reiser and Last, 1979;). It is generally believed that the action of quartz particles on the cell membrane is the starting point of the silicotic process (Farber, 1983; Parazzi et al., 1968). Thus the surface characteristics of the quartz particles have been the subject of several recent studies (Bolls et al.. 1983; Dalai et al., 1986; Fubini et al., 1987). Recently, We reported that mechanical crushing of quartz under normal atmosphere generates free radicals which decay with time, and that these free radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to aged dust from the same stock (Dalai et al., 1986; Vallyathan et al.. 1988). The formation of Si• and. SiO--type of radicals from quartz particles crushed under atmospheric conditions has also been reported by Fubini et al. (1987). In addition, Gulumian and van Wyk (1987) have reported that quartz particles react with hydrogen peroxide (H202) to generates hydroxyl radicals (•OH) and suggested that this process might contribute to quartz's pathogenicity. However, these authors did not report the effects of metal chelators, so it was not clear as to whether the detected -OH radicals simply resulted from the Fenton reaction involving exogenous metal ion contaminants. Earlier, Marasas and Harington (1960) reported that quartz particles could function as an oxidant in a number of in vitro oxidations, including the hydroxylation of proline and lysine. They postulated that silica dusts, on reacting with water, could release H2O2 which might have the potential to react with various biological constituents and thus cause tissue damage. In fact, Gabor and coworkers (Gabor and Anca, 1974; Gabor et al., 1975) suggested that the cytotoxicity of quartz particles might be associated with the generation of some 'factor or factors possessing the properties of a free radicals capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently Weitzman and Graceffa (1984) reported that asbestos is able to catalyze the generation of • OH radicals from H2O2. Their later work indicated that lipid peroxidation may be one of the mechanism by which asbestos produces tissue injury (Weitzman and Weitberg, 1985). This is significant because • OH radicals are capable of causing peroxidation by abstracting hydrogen atoms from cell-membrane lipids and initiating lipid peroxidation in lysosomal membrane (Fong et al., 1973). In fact, the formation of oxygenated species in reactions involving quartz was suspected since Kolbanev et al. (1980) reported the detection of H2O2 in the reaction of fresh quartz particle with aqueous medium. The present work was thus undertaken to detect the anticipated formation of some oxygenated, radical species by reactions of quartz in a cell-free media and its inhibition by radical"

Jan 1, 1988

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

By D. L. Sawyer

Aqueous C12-02 leaching procedures developed by the Bureau of Mines to produce zinc chloride from zinc sulfide bulk concentrates were effective in extracting 99 pct of the zinc and 97 pet of the silver contained in samples of massive seafloor sulfides from the southern Juan de Fuca Ridge. Zinc sulfide (sphalerite and wurtzite) mineralization comprised 55 and 88 pct of two specimens provided by the U.S. Geological Survey for this study. Minor occurrences of galena, chalcopyrite, and other minerals in the sulfides permitted the recovery of pregnant liquors that were low in metal values other than zinc, which were successfully purified by a two-step cementation procedure using zinc dust.

Jan 1, 1983

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington, The investigation consisted of transit and topographic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds Were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and analyzed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing new sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest.

Jan 1, 1948

By Foster Fraas

The response of minerals in magnetic separators is in accordance to dynamic rather than static magnetic susceptibility values . The dynamic value varies with respect to both passage speed through the separating field and time of exposure in a preliminary treatment field . Tests on 16 minerals and solids have demonstrated that both of these factors affect different minerals in different ways .

Jan 1, 1964

By Stephen D. Cramer

A nondestructive procedure for measuring electrodeposit porosity has been developed which records the location and number of deposit defects including pores, pits, and voids. The procedure involves the passage of an X-ray beam through the deposit-substrate system onto suitable film. The defects are recorded as images on the film. Variables studied included intensity and spectra of the X-ray beam, composition and thickness of deposit and substrate, film type and developing procedure, and limits for detecting defects. At an X-ray tube voltage of 40 kv, pores several mils thick were easily detected in copper-nickel specimens more than 20 mils thick. To illustrate the utility of the procedure, the effect of substrate oxidation and of current density on electrodeposit porosity was briefly studied.

Jan 1, 1970