Search Documents

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

Develop a means for estimating vertical stress conditions in or around an underground mine so that appropriate measures for ground control can be taken before hazardous conditions arise. Background High vertical stress in an underground mine could cause or enhance hazardous ground control conditions which might lead to accidents, fatalities, and loss of reserves. An understanding of the vertical stress conditions at the mining level would allow a mine operator to take precautions that will minimize the occurrence of ground control problems. A knowledge of the underground stress conditions prior to mining could be used as an aid in future mine plan development to avoid or minimize ground control problems. Approach The Bureau of Mines developed a computer program for calculating the vertical stress resulting from the pressure of overlying rock masses on a mine or geologic surface at various depths.

Jan 1, 1990

By F. N. Kissell

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Aug 1, 2009

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By T. J. Ballard, Austin B. Clayton

"The Union Copper mine is in the Gold Hill district, Rowan and Cabarrus Counties, N. C.The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907.As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes, totaling 2,500 linear feet, were drilled to delineate the ore body. Analyses of 205 core samples were made.Tabulations of sample analyses and drill-hole logs are presented in this report.The project work embodied in this report was under the immediate supervision of Austin B. Clayton, project engineer, and the general supervision of H. B. Ewoldt, district engineer for North Carolina and Tennessee. The preliminary report, written by Austin B. Clayton, was revised and the various figures redrawn for publication by T. J. Ballard under the general supervision of M. H. Kline, chief, Raleigh Branch, Mining Division.Acknowledgment is due the Metallurgical Branch for analytical determinations of the samples.The mine property is 1.5 miles southwest of the village of Gold. Hill, N. C. (fig. 1). Gold Hill is on U. S. Highway 52 between Salisbury and Albemarle and on a branch line of the Southern Railway. The latitude is 350 30' and longitude 80° 21 The tract consists of 553-1/2 acres in Cabarrus and Rowan Counties.A tentative list of the surface-rights ownership is as follows: William Hoy Barringer - 16 acres, A. W. Tucker - 1 acre, Frank Wagoner - 4 acres, and George Barringer - 3-1/2 acres, in Cabarrus County; A. W. Tucker - 2 acres, H. N. Hedrick - 54 acres, and William Atkins - 473 acres, in, Rowan County, N. C.The mineral rights are owned by Alfred Rossiter, Alice R. Hesslein? and the estate of the late Bella Rosenblatt. The attorneys for the owners are Neidle & Taylor, 6 East 45th Street, New York City.The Union Copper mine is in the Cold Hill mining district of North Carolina where gold was first discovered in 1799. The upper parts of the veins in the district were first worked for gold; however, the increase in the sulfide content of the veins with depth rendered the amalgamation process for gold recovery ineffective, and the mines were closed.The period of greatest activity at the Union Copper mine was from 1899 to 1906. At an earlier period the oxidized and leached part of the lode near the surface was mined from a working known as the ""big cut,"" the reported yield of which was $300,000 in gold.3/ The mine has not been operated since 1907.J. T. Pardee3/ lists the probable value of the production of the Union Copper mine as $1,050,000, of which about $675,000 was the value of some 5,000,000 pounds of copper produced."

Oct 1, 1948

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

By W. A. Jacob, E. W. Dean

The Pittsburgh petroleum laboratory of the Bureau of lines has recently developed an improved method for the determination of water in pctroleum emulsions. It has been described in detail in an article entitled "A convenient method for the determination of water in petroloum and other organic emulsions" by E. W. Dean and D. D. Stark (Jour. Ind., and Enc. Chem. Vol. 12, ſay, 1920, page 436). It is essentially a modification of the familiar procedure of "distillation with an iniscible solvent", the improvement consisting in the use of apparatus that is rºck more convenient than any previously employed. The method has been used with marked success in the Bureau's laboratories for a period of about a year and has also been tried with equal satisfaction by a number of other laboratories. It has been most extensively employed for determining the water content of heavy fuel oils but has been applied also to several other types of emulsions, including shale oils, tars derived from coal, greases, and mixtures of powdered coal, oil and water. The Bureau has received a number of requests for information regarding commercial sources for the apparatus used, and having been assured of the value of the method, has taken steps to render it available for general use. - The equipment is, with the exception of two items, made of parts that are obtainable from the ordinary stock of chemical supply houses. The two exceptions are (1) the so-called "distilling tube receiver" and (2) the electric heater. The former is an essential part of the equipment; the latter is a convenient ac cessory but it can if necessary be roplaced by a gas burner. Efforts on the part of the Bureau staff to ronder these two items of apparatus available for purchase from supply houses, or for production by the user are hero described.

Sep 1, 1920

By J. D. Tolman

In view of present interest in a revival of gold mining enterprises, papers dealing with the development of small gold properties are apropos. The present paper deals with the operation of a small gold property in the exploration and development stage, mining and milling 25 tons of ore daily, and indicates what may he expected in the way of mining costs under northern climatic conditions, by practicing rigid economy, at a property where disproportionate overhead costs are unavoidable bacause of the small rate of production. The output of this prospect is treated in a small amalgamation plant which has been described in a previous circular.. HISTORY Prospecting in the district was begun in 1909, and by 1911 the adjoining mines, Hollinger and McIntyre, were in operation. Actual work was begun on the Rochester claim in July, 1922, and carried on through 1924. The property was closed until 1928 when the present company took it over, together with the other holdings of the Canadel Mining Co. A small mill was started as a pilot plant on March 24, 1929, and is still in operation.

Jan 1, 1931

By Jeffrey Shawn Peterson

In past years, the U.S. Bureau of Mines has been involved in safety research that could ultimately re-late the conditions of spark testing and actual use by estimating the simple ignition probability of a circuit in question. A major problem in estimating this probability is that results show a significant variability, even though gas mixtures and electrical parameters may be closely controlled. Some researchers have suggested that the ambient environmental conditions of the testing may influence the results. A series of tests were conducted using a spark test apparatus to simulate a failing electrical circuit. By independently adjusting the temperature, pressure, or relative humidity of the combustible gas mixture, multiple test environments were examined. At each ignition, a computer re-corded the temperature, pressure, and relative humidity of the gas immediately prior to the explosion. These data were then used to establish the effect of the test environment on the ignition probability and to create a mathematical model of the test environment's synergistic effects. The analysis indicated that these effects were not as significant as previously expected. No general algorithm was found that could be used to predict these effects across the range of circuits tested.

Jan 1, 2010

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

By W. H. Young

PRODUCTION of bituminous coal and lignite increased substantially in 1963 compared with 1962 figures. The major items of production, consumption, exports, and productivity increased. However, certain key items declined. For the fourth year there was no upward trend in mechanization; the percentage of total tonnage mechanically loaded remained the same as in the 3 previous years and the percentage of total tonnage mechanically cleaned was smaller than in the previous year. Furthermore, the percentage of total production mined by stripping and by augers increased. Most significant was the continued decline in average value and employment. Production.-The output of bituminous coal and lignite in the United States in 1963--459 million tons-was 9 percent greater than the 422 million tons produced in 1962. Production was greater in 1963, largely because of expanded consumption by the electric utilities and an increase in exports.

Jan 1, 1964

By J. H. East

Potash is one of the essential chemicals used in fertilizing soil deficient in natural minerals . Europe uses a large tonnage of potash in the form of easily soluble salts , and this is particularly true of those countries where the natural minerals in the soil have been exhausted owing to intensive cropping of the land . The application of potash to the soil in these countries is essential if normal crops are to be obtained ; during the war , some European countries were unable to obtain sufficient potash , and productivity of the farming areas declined seriously . • The largest -known deposits of potash in the world ; with the possible. exception of Russia , occur in Germany , and the German output of processed salts constituted about 65 percent of world production prior to the war . The German potash-plant installations are large , modern , brick and steel construction and apparently built for a planned operation of many years . Two districts produced approximately 80 percent of the German potash; the Werra -Fulda district , near Vacha , had the largest production , and the Sudharz district , near Nordhausen and Sonderhausen , was second . (Fig . 1. ) Hannover and Stassfurt were two smaller producers . Potash fertilizers are rated in terms of potassium oxide (K20 ) . The usual basis for calculation of production or application of the salt is to reduce the potash content to 40 percent K₂0 .

May 1, 1947

By S. A. N. Sheya

Many gold-bearing ores in the Western United States also contain small amounts of mercury. The presence of mercury creates potential pollution and health hazards during several steps in gold processing. An investigation was undertaken by the Bureau of Mines to develop techniques for removing mercury from cyanide mill solutions by selective electrowinning to reduce the potential hazards. Sixty-five percent of the mercury was selectively electrowon from synthetic carbon strip solution at applied potentials of 1.00 to 1.50 V when using a mercury-coated platinum or copper plate cathode. Increasing the active surface area by using mercury-coated copper wool resulted in up to % pct of the mercury being electrowon from mill carbon strip solutions that contained 1.9 to 20 ppm Hg, 20 to 345 ppm Au, and 0.35 to 39.5 ppm Ag. About 98 pct of the silver was electrowon with the mercury onto the mercury cathode. Gold extraction ranged between 0 and 20 pet. Results of the investigation showed that choice of cathode material was critical to the success of the process. Selectivity was not achieved using uncoated steel wool cathodes.

Jan 1, 1988

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By Joan Weinberg

The real gross national product (GNP) advanced at a annual rate of 3.1 % during the second quarter, following a revised 3.4% increase in the first quarter (see table 1). Export growth continues to play an important role in the rising output. Combined with the decline in imports, it resulted in a noticeably improved trade position. Imports of consumer goods, including automobiles and food, fell while exports rose. Imported cars have been losing ground to domestic cars. The foreign car share of the U.S. market fell from 36% in October 1987, to 29% in May 1988. Business spending for new plant and equipment contributed strongly to the GNP increase. Equipment purchases, particularly of computers, rose at a 14.8% annual rate, following a large first-quarter gain. Purchases of structures rose 11.8%. The other key component of business spending, change in business inventories, declined from the first quarter. Inventory buildup in late 1987 had been considered excessive.

Jan 1, 1988

By Charles W. Huggins

DEVELOPMENT of the electron microscope has permitted man to examine many small objects that could not be resolved by the light micro-scope. Diffraction, spherical aberration, and chromatic aberration are the main factors that limit resolution to about two-tenths micron with the light microscope. No matter how perfectly a light microscope is constructed and operated, it cannot possibly resolve points separated by less than two-tenths micron. Rapid development following World War II has produced many electron microscopes capable of 20 A resolution. Fibrous inorganic minerals are well suited for electron microscopic study. Many micrographs of chrysotile have been published, but electron microscopic study of the amphiboles has been somewhat neglected. New techniques in sample preparation have simplified the study of fibrous material. Ultrasonic energy has been very helpful in sample dispersion. This publication contains a representative group of electron micrographs of natural inorganic fibers that have industrial value. These fibers commonly are referred to as the asbestiform minerals. The Bureau hopes that the knowledge gained through electron microscopy and other scientific study of the natural inorganic crystalline fibers eventually will lead to the production of synthetic fibers that will satisfy the requirements of industry.

Jan 1, 1959

By Keith L. Harris

Real gross national product3 (GNP) grew at a seasonally adjusted annual rate of 4.2% in the fourth quarter compared with a revised 4.3% rate in the third quarter, according to the most recent estimates released by the U.S. Department of Commerce (table 1). Expanding inventories, Government purchases of goods and services, residential fixed investment, and a narrowing of the trade deficit fueled the growth. Significantly reduced consumer demand led to the heavy inventory growth. Almost half of the buildup in inventories consisted of automobiles because consumers reduced purchases when Detroit ceased most incentive programs in late summer. Reduced consumer demand also affected imports, however, and the narrowing of the trade deficit resumed after widening in the third quarter. Nonresi- [ ] dential fixed investment also declined after a strong gain in the third quarter. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 2.9%, the same as that of 1986. However, on a fourth-quarter-to-fourth-quarter basis, the real growth reached 3.8%, the highest growth since 19M, and exceeded the Reagan Administration's estimate of 3.4%. Rising merchandise exports accounted for about one-third of the growth in GNP for all of 1987 and are expected to continue to grow as domestic manufactures benefit from the lower value of the dollar vis-a-vis other major trading country currencies. Consumer demand became a less important factor of economic growth, but employment continued to grow (table 2), and civilian unemployment declined by 0.9 percentage points (December to December) as the industrial sector geared up to increase exports. Inflation, as measured by the fixed-weighted GNP price index, remained low at 3.4%.

Jan 1, 1988