Search Documents

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By E. D. Eastman

"The factors that determine the efficiency of reduction of iron oxides by gaseous reducing agents may be considered in two classes; those which effect the equilibrium between the reacting substances end their products, and those which affect the rete of reaction. Both sets are of prectical importance, the former as influencing the maximum possible efficiency and the latter as determining what fraction of the maximum yield may be readily or profitably obtained. In addition, the thermal changes attending the reduction greatly affect the chance of successful industrial application of any such process, and knowledge of them is necessary for the intelligent design of apparatus and control of the reaction. Some aspects of each of these three divisions of the problem are discussed below.I. The Maximum Reducing Power of Fuel Gases on the Oxides of IronsThe gases that heve been considered specifically in this work are coal gas, water gas and producer gas, typical analyses” of which are given in Table 1 Of the various hydrocarbons represented in Table 1, (several being grouped or averaged as C2R4), methane is the only gas assumed to be capable of existence at appreciable pressures under the conditions of interest here. The equilibria in the several systems which may ensue when one of the above gases is allowed to react with the iron oxides, may therefore be represented in the most general case by equations of the type of the following arbitrarily chosen ones:"

Jun 1, 1923

By Albert Mendelsohn

This paper, describing the mining practice at the Champion mine of the Copper Range Copper Mining Co., is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. Mining practice at the Champion mine has undergone considerable change during the last four years. Previous to that time the mine was worked by the horizontal out-and-fill method, the stopes starting near the shafts and advancing away from them (fig. 2). The floor pillars were mined by the inclined cut-and-fill method, working en the retreat or toward the shafts (fig. 1). At present the mine is being developed to .tope entirely on the retreat by a sublevel inclined cut-and-fill method.

Jan 1, 1931

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By Alla D. Mah

The work described in this report is part of a Bureau of Mines research program for obtaining heats of formation of inorganic oxides, carbides, and nitrides by combustion calorimetry. The heats of combustion of molybdenum subnitride (Mo2N) and chromium subnitride (Cr2N) were measured. The data were combined with previous determinations of the heats of formation of molybdenum trioxide and chromium sesquioxide to obtain the heats of formation of the two subnitrides from the elements at 298.15° K. The corresponding free energies of formation were estimated. The heat data were compared with those of nine previously studied nitrides.

Jan 1, 1960

By C. E. Brechtel

Cooperative research efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, used a one-dimensional, finite-element computer model to simulate turbulent mass transfer in face ventilation of oil shale mines. The objective was to study the dilution of methane released by rubbled oil shale during blasting. A methane release rate function was developed from the back-analysis of field measurements, and the finite-element model was calibrated using tracer gas characterization data from tests of full-scale face ventilation systems.

Jan 1, 1989

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By S. L. Windes

For a number of years, the Bureau of Mines conducted tests on various types of structures to determine the effect of seismic vibrations emanating from quarry blasting in an effort to determine an index of damage . Associated with these tests , occasional records were made of the characteristics of. the air blast or concussion from the explosions . Although the importance of the air - blast problem was recognized , the equipment was not designed for air -blast measurements , nor was the early research program concerned with the problem . After the ground - vibration tests had been completed , attention was turned to study of the air blast and its effect . The air - blast problem in reference to quarry and mine blasting may be divided conveniently into three phases : (1 ) Determination of the fundamental characteristics of the air blast , such as the pressure - time relationship , speed of propagation, attenuation , and the like ; ( 2) effect of blasting conditions on these air -blast characteristics ; and ( 3) determination of the conditions necessary for damage to structures . The initial step was the development of microphones suitable for recording the anticipated blast pressures. Such microphones were designed and built during 1940 , and described in technical detail for publication ( 2)3/. Briefly, the microphone adopted was a small, plate - diaphragm condenser type . The recording was through special transducer amplifiers with low -frequency response to zero cycles per second and a Duddell - type oscillograph of special design .

Feb 1, 1942

By F. F. Aplan, J. A. Gutierrez-Rodriguez

"Contact-angle and flotation techniques were used to evaluate the influence of oxygen - both that inherent in the coal and that introduced by ambient temperature, aqueous oxidation - on a wide range of coal ranks. Oxidation was found to decrease the hydrophobicity and floatability of coal; with the effect being minor for coals of high rank but becoming increasingly important as the rank of coal is reduced. As an approximation, oxidation makes a coal behave as if it were one of lower rank. Frother only flotation' of coal· correlates with the captive-bubble contact angle whereas when oil is used as a collector, the flotation appears to follow the pattern shown by the water sessile drop on a fresh, un-reagentized coal surface. Coal recovery lost through oxidation may often be recovered by use of a variety of collectors, of which No. 2 foe! oil is among the best of those reagents tested. A simple alkali-extraction test may be used to estimate the influence of oxidation on coal preparation processes and use.INTRODUCTIONThe hydrophobicity of coal is not only a function of its rank but also of the extent of oxidation of the coal during and subsequent to its formation. Weathering and oxidation processes may proceed in-situ for coal deposits that outcrop near the earth's surface, or the oxidation of the coal particles may occur during mining, stockpiling or processing. Such oxidation, whether it affects the bulk-coal sample or on1y a thin outer layer on the coal surface, can dramatically influence the wettability of the particle and hence such processes as flotation, filtration, flocculation and dispersion.Many of the studies made on the oxidation of coals ·were designed to study its effect on flotation, coking or pyrolysis. The. present study 'is directed exclusively toward the effect of oxidation on the hydrophobicity and floatability of the coal. One of the first studies of the effect of oxidation on coal flotation was that of Sun [l] who found that as oxidation proceeds, coal becomes progressively more hydrophilic. Low-temperature oxidation (100-150°C for 250 h) generally lowered the coal floatability with an oily collector only slightly, but more extensive oxidation (200- 3500 C for 250 h) reduced coal floatability seriously. Sun also found that cationic amines were effective collectors for the oxidized coal which infers that oxidation makes the coal more negative in solution. He attributed the loss of floatability to be due to the accumulation of water-insoluble oxidation products at the coal surface. Gayle et al. [2] found that oxidation adversely affected coal flotation when an aliphatic-alcohol frother was used, though a small amount of oxidation appeared to improve the floatability of some coals using a kerosene-pine oil, collector-frother mixture in pilot-plant testing. Prolonged oxidation adversely affected the flotation recovery of the coals tested, the effect being more pronounced when an alcoholic-type frother only was used. They also noted that the reduction in floatability of lower rank bituminous coals was more affected by oxidation than was that of higher rank bituminous coals."

Jan 1, 1989

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By H. H. Dewing

The U.S. Bureau of Mines characterized Hg-containing wastes and used a thermal-desorption process to remove and recover the contained Hg. The wastes were generated by an electrical-parts plant engaged in the assembly of Hg-containing switches and contained phenolic resins and paper insulating materials mixed with soil. The average Hg content was 396 ppm. Numerous characterization tests showed the Hg was tightly absorbed and could not be removed or concentrated by leaching or gravity separation techniques. Laboratory retort tests showed the Hg content reduced to < 16 ppm in 2 h at 400 °C; rotary-kiln, thermal-desorption tests required 4 h at 450 °C. Airflow through the retort im¬proved thermal-desorption efficiency, but vacuum operation only slightly reduced the temperature needed for thermal desorption. Offgases from decomposition of organic materials were burned in a high-temperature afterburner and subsequently cooled in a heat exchanger to condense water vapor. Finally, the Hg vapor was condensed and absorbed from the offgas by activated charcoal. Mercury recovery was over 99.99 pct of the desorbed Hg. Thermal-desorption processes have had wide application to many Hg-containing wastes, and historical experience in Hg mining has demonstrated its potential cost effectiveness.

Jan 1, 2010

By Jeffrey S. Walker

Abandoned underground mine openings are susceptible to collapse because of the mining methods used, the character of the overburden, and the typically large, wide entries with minimal roof support. The final effect of the collapse of the underground workings is surface subsidence. To reduce the probability of subsidence, methods to backfill the mine void with various types of materials have been developed. This U.S. Bureau of Mines report describes the available technologies for subsidence abatement and discusses their operation and application. The basis of these abatement methods is the replacement of the mined material with mine waste. Backfilling of mine voids is the most common method of stabilization used to abate subsidence and protect surface structures. Hydraulic flushing and grouting, using remote methods from single or multiple boreholes, are the most often-used methods for the placement of backfill material. Other subsidence abatement techniques are available and may be more appropriate under different conditions. These other techniques include pneumatic stowing, either by in-mine or remote methods, and various point support methods that do not completely fill the mine void and are used for the protection of small areas of the land surface and surface structures.

Jan 1, 1993

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969

By H. R. Babitzke

The purpose of this Bureau of Mine- investigation was to develop columbium and tantalum alloys suitable or u at elevated temperatures. Columbium and tantalum were combined with tungsten, hafnium, zirconium, molybdenum, vanadium, and titanium, and the resulting alloys were evaluated with respect to workability, hardness, electrical resistivity, strength at elevated temperatures, oxidation resistance, and weldability. Cb-33Hf-10W-10Ti, Cb-20111-5Mo, and Cb-30Hf-5Mo exhibited superior high temperature properties. Cb-33Hf-10W-10Ti had tensile strength values of 44,300 psi at 1,200° C and 16,500 psi at 1,400° C, Cb-20Hf-5Mo had values of 35,700 and 20,700 psi, respectively. The corresponding values for Cb-30Hf-5Mo were 38,900 and 17,800 psi. These alloys are fabricable by conventional methods with excellent strength at temperatures up to and including 1,400° C. An oxidation rate of 7 to 21 mg/cm2/hr was observed up to 1,000° C.

Jan 1, 1967

By R. O. Dannenberg

A metallic displacement process, utilizing easily available steel wool or steel window screen, was devised and successfully used for the recovery of silver from waste photographic fixing solutions. Laboratory and prolonged commercial-scale testing established that the iron filament type unit will efficiently precipitate silver, as a high-grade sludge, from acidic waste photographic fixing solutions ranging in grade from less than 1 to over 10 grams of silver per liter. Data and design information are presented to facilitate the construction and operation of a practical unit of any desired size. A smelting process for recovering pure silver from precipitated sludge containing 27 to 80 percent silver was devised.

Jan 1, 1968