Search Documents

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By Robert G. Clarke

The production of natural abrasives varied in quantity and value compared with those of 1974. Output of tripoli-type materials and garnet both decreased in quantity and value. Special silica stone products decreased in quantity but in-creased in value. The production of emery increased 38% in quantity. The production of manufactured abrasive materials decreased for all types and the decreases were more in quantity than in value. [ ] FOREIGN TRADE Imports of abrasive materials were 15% less in value than in 1974, and exports plus reexports decreased in value 10%. Net exports, the excess of exports and reexports over imports, were $9.3 million, about four times that of 1974. The volume of all abrasive materials exported decreased and the value of nearly all decreased.

Jan 1, 1977

By Charles Janin

The recovery of gold from sands and gravels is one of the oldest forms of mining; it antedates history and has been practiced by savage peoples. In North America the search for placer gold has been a powerful agency in the exploration and development of unknown regions and has profoundly influenced the course of our civilization. With the progress of invention, the improvements in machinery, and the availability of large capital for the conduct of great operations, the tendency in placer, as in many other branches of mining, has been toward the working of extensive but comparatively low-grade deposits. The early miner washed the rich spots in stream beds or terraces with his pan, his long tom, and his primitive sluice. Then followed the growth of hydraulic mining and the use of giants supplied with water under pressures of hundreds of pounds to the square inch that could work at a profit gravels whose gold tenor was less than 3 cents to the cubic yard. Finally came the dredge that could handle deposits lying so far below water level as to be beyond attack by other methods. Although the gold dredge was first successful on a commercial scale in New Zealand, it has reached its present strength and efficiency in this country and its development is a monument to the daring, per- severance and technical skill of the many men, mine owners and engineers who have each contributed something to the final result. The Bureau of Mines, authorized to conduct investigations for the purpose of increasing efficiency in the mineral industries, had its attention called some years ago to the need of a comprehensive report on gold dredging in the United States. The director of the bureau recognized that such a report should summarize the development of the gold dredge, should describe in detail the essential features of present-day dredges, should discuss the facts that determine whether a placer deposit can be profitably dredged, and should point out the approved methods of prospecting placer ground and of operating dredges. At the request of the director, the author undertook the preparation of such a report and has been intermittently engaged on the task for several years. This bulletin is the outcome of his labors. He hopes that it will prove of interest to designers and builders of dredges, to mining engineers, and to persons who may contemplate investing capital in placer-mining ventures.

Jan 1, 1918

By Doris M. Hyde

In the past, mining has represented between 11% and 12% of the gross domestic product (GDP). In 1982, mining contributed over $150 million to the estimated $1.4 billion GDP.2 Overall economic growth for 1983 was projected at about 2%, primarily as a result of increased tourism. The inflation rate remained at or fell below the 1982 level of almost 4%. The Government continued its efforts to strengthen the industrial base by improving infrastructural systems and the establishment of a free trade zone. Laws against property ownership by foreigners or foreign-owned companies were strengthened, but the prohibition was softened to allow for close family inheritance. Otherwise, Government approval must be obtained to retain property acquired through inheritance, court order, mortgage, or other means. Special consideration was granted to foreign investors seeking to promote industries beneficial to the economy.

Jan 1, 1985

The mineral industry of Benin contributed less than 1% of the 1977 gross domestic product (GDP), which was estimated at $500 million.' Other than limestone and salt, no exploitable mineral deposits have yet been discovered in Benin, which has been rated by the United Nations as one of the world's least developed nations. In 1977, the economy was further weakened by petroleum price increases and severe drought. The country continued to depend on foreign assistance, which averaged $20 million per year, to finance development projects. The country's first 3-year plan, which was put into operation in October 1977 after many delays, allocated more than $1 billion to projects in infrastructure, agriculture, and light industry. The most important infrastructure project was the expansion and modernization of the port of Cotonou, valued as an entrepôt port for the transit of goods to the neighboring countries of Niger and Nigeria. Plans called for an increase in handling capacity to 1 million tons of cargo annually, the improvement of port and cargo handling operations, and the upgrading of the efficiency of the Port Autonome de Cotonou (PAC) management system. The $46 million project was to be financed by a consortium led by the International Bank for Reconstruction and Development (IBRD) and including Canada, France, Nigeria, and Abu Dhabi. Construction was scheduled to begin in 1978 and be completed in 1980.

Jan 1, 1981

By David S. Yantek

Miners in underground coal mines experience prolonged exposure to high noise levels, often with A-weighted sound levels in excess of 90 dB. Field tests have shown that the continuous miner conveyor is a dominant noise source. This paper will identify the most significant noise-radiating surfaces on the continuous miner tail section using vibration levels and surface areas to estimate the sound power levels of each surface. In addition, using five test cases, this study will examine the effects of three engineering noise controls on the surface-averaged vibration levels and average sound levels measured with four microphones located two meters from the tail section. The noise-radiating surfaces of the conveyor’s tail section include the top and bottom decks, the sideboards, and the flex plates. Emphasis is placed on the changes in the estimated sound power levels in the 500 – 2500 Hz 1/3-octave bands since this frequency range accounts for 80-85% of the sound energy near the tail section. The results show that the bottom deck is the most significant noise radiator for the untreated miner. Installing a coated bottom deck reduces the estimated sound power level radiated from the bottom deck by 11 dB and the average sound level by 2 dB. Using a coated tail roller results in reductions of the estimated sound power levels for individual components from 1 to 4 dBand reduces the average sound level by 2 dB. Coating the slide plate has little effect on both the estimated radiated sound power levels and the average sound level. The test results indicate that modifications that reduce flex plate vibration and reduce energy transfer from the tail roller into the tail section will be effective in reducing noise when combined with a coated tail roller and coated return deck.

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, staurolite, and emery, increased in 1987. The increase was, in certain cases, because the materials were used in nonabrasive applications, such as the increased use of tripoli as a filler and special silica stone material as a special-purpose crushed stone. The increased use of garnet as a blasting media accounts for most of its growth. Production and sales of garnet were at a record-high level in 1987. [ ]

Jan 1, 1989

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By H. F. Yancey, E. Zane

"INTRODUCTION The term ""friability"" as applied to coal may be defined as the physical property of coal which expresses its tendency to become reduced in size during handling as a result of such external forces as impact and attrition. Thus friability is a quantitative concept and property, and hence can only be defined in relative terms or in terms of measurement. Methods of measurement are difficult to formulate and apply because coal is anything but homogeneous in physical structure and chemical constitution. aMoreover, friability itself is a composite property obviously dependent upon a group of other specific characteristics such as cleavage, fracture, tenacity, hardness, and elasticity, which vary from coal to coal with change in rank and even between individual coals of the same rank. These characteristics affect the friability values of different coals to varying degrees, but this fact does not impair the usefulness of and the need for friability measurements.The amount of breakage or degradation in size that a coal suffers in mining, preparation, and subsequent handling depends upon its inherent friability and the severity of the handling treatment which it receives from the time it is taken from the bed until it reaches the consumer. The value of the coal to the producer and jobber depends in large measure upon these same factors--friability and severity of treatment—because the larger sizes still command a premium in the ordinary market. Although much has been accomplished by the coal-producing industry in minimizing the breakage of coal in mining and preparation, it is apparent that additional reductions in breakage must await further improvements in design of coal-handling equipment. Such improvements will result from more intensive investigations of the extent of breakage or degradation in size occasioned by specific mining and handling operations and the development and application of standardized methods of evaluating friability.The work described in this report was undertaken to assist in the development of standard methods for evaluating the friability of coal. Specifically, the work deals with a Comparison of the various methods previously proposed for estimating the friability of coal and coal products. This same objective is now being sought at a number of other institutions, both in the United States and Canada, by a committee of the American Society for Testing Materials. It is believed that by providing additional information concerning a property of coal pertinent to its increased usefulness, the work described will supplement and increase the useful of the data which long have been, and still are being, furnished by the bureau of Mines on the composition of coals of the United States."

Jun 1, 1933

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By Arthur L. Murray

"INTRODUCTION In compliance with those provisions of the organic act establishing the Bureau. of Mines which relate to improvement of health conditions of persons engaged in the mining, preparation, or treatment of mineral substances, sanitary surveys have been made of towns and villages housing the coal miners, metal miners, and mill and smelter employees of Utah.The purpose of the surveys is to afford studies of conditions prevailing in the various mining and smelter towns so far as concerns housing, water supplies, sewage disposal, refuse disposal the handling of foodstuffs, general sanitation, wash and. change houses, and the control of preventable diseases, all of which directly or indirectly have a bearing on the health and efficiency of employees and their families. Certain other factors have been added to the general sanitary surveys such as school and recreational facilities, which have a decided influence on contentment and efficiency. Through comparisons of favorable and unfavorable conditions and practices, and the dissemination of such information, improvements can be effected which will benefit both the employees and the employers.ACKNOWLEGMENTSAcknowledgment is made of the many courtesies shown by the officials of companies and towns visited. In some instances the towns were entirely under the control of officials of mining companies, being on company property whereas, in other instances, the towns wars incorporated not under company management. Particular acknowledgment is made of the assistance given by the Utah State Board of Health through Health Commissioner Dr. T. B. Beatty."

Oct 1, 1932

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra Brake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDB listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

For the sixth year in a row, the value of nonfuel mineral raw materials produced in the United States set a new record, reaching almost $17 billion in 1977. Data provided by the Bureau of Mines show that the 1977 value of domestic nonfuel mineral production exceeded the 1976 value, $16.7 billion, by 2 percent. The $17 billion worth of minerals was the basis for approximately $770 bill ion worth of processed materials of mineral origin. Output of metals decreased $360 mil lion in 1977, while that of nonmetals increased $670 million. Of the 22 metals produced, output of 12 increased, and the value of 13 increased. Among the 46 nonmetallic minerals produced, the quantity of 27 increased, and the value of 34 increased.

Jan 1, 1978

By D. T. Randall, H. W. Weeks

The burning of coal without smoke is a problem that concerns the Government directly because of the advantages of smokeless combustion both in public buildings and on naval vessels. In addition, smoke abatement is a factor in conserving the fuel resources of the United States. Hence, as part of its general investigation of the best methods of utilizing the coals of this country, the Bureau of Mines, which is in charge of the fuel-testing work formerly carried on by the United States Geological Survey, has made extended tests to determine the conditions necessary for the smokeless combustion of bituminous coal in boiler furnaces. Bulletin 39,a a preliminary report, treats the smoke problem from a theoretical point of view, detailing the steps that are being taken by . municipalities, manufacturers, and citizens to abate smoke, also showing the possibility of a clean city. The present bulletin not only shows that bituminous coals high in volatile matter can be burned without smoke, but also that large plants carrying loads that fluctuate widely, where boilers over banked fires must be put into service quickly and fires forced to the capacity of their units, can be operated without producing smoke that is objectionable. Proper equipment, efficient labor, and intelligent supervision are the necessary factors.

Jan 1, 1912

"M bed, Matanuska valley, Alaska, coal carbonizingproperties B 510M spectral lines, low-energy, study RI 5538Mab shaft, Leadvile district, Colo., investigation RI .1518Maberry process, for aluminum chloride TP 321"

Jan 1, 1960

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.