Search Documents

By L. C. IlsLey

Through the cooperation of the Pennsylvania Department of Mines the writer obtained from State, records detailed information concerning coal-mine accidents occurring in Pennsylvania bituminous mines during 1939, particularly those nonfatal accidents in which the injured person lost 60 or more days? time from mark. The writer wishes to acknowledge assistance received from Pennsylvania State officials, especially Richard Maize, secretary of mines, and. Joseph J, Walsh, deputy secretary of mines; also to Thomas Dickinson,3/ of the Bureau of Mines, who rendered valuable assistance in assembling the data an the several tables.

Jan 1, 1941

By Michael S. Miller

In 1985 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the 17,000-acre Pyramid Peak planning area in order to evaluate its identified mineral resources. The planning area is located in Riverside County, CA, 15 miles south of Palm Springs. The planning area contains marginally economic resources of marble and mica, subeconomic resources of garnet and occurrences of gold and tungsten. The area is underlain by marble, quartzite, schist, migmatite, intrusive rock, and a wide zone of intensely sheared rock. Quaternary stream, landslide, talus, and colluvial material overlie the older rocks. Ten claims for marble in or overlapping the southwest and southeast parts of the planning area are current (1986). Many other current claims are outside the planning area, adjacent to or within 2 miles of the southwest and southeast corners. Hundreds of millions of tons of inferred, marginally economic marble in and near the planning area may be mined for cement or lime after other developed resources near markets are depleted or if large-scale construction or other markets develop nearby.

Jan 1, 1987

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

Australia is tightening its rules governing mineral processing and the purchase of rural land by foreign investors" Rural land purchasers in the future will have to demonstrate to the Foreign Investment Review Board, the applicable governing body, that they will introduce new techniques or developments that will benefit Australia. In mineral processing, the criterion will be the availability of maximum opportunities for Australian equity capital. The changes are designed to discourage absentee landlords and speculators from abroad. A diamond field discovered several years ago in the northern section of Western Australia, known as the Kimberley region, is now thought to be one of the largest in the world, according to Conzinc Riotinto of Australia Ltd. (CRA). Figures released late in 1981 by CRA indicate that the main orebody of at least 100 million metric tons contains possibly 500 million carats of diamonds with a conservative market value of $8 billion. The diamond stones in the 100-acre deposit are about 10% gem-quality, 30% near gem, and 60% industrial. Initial production is expected to be about 17 million carats annually, which could be expanded to 25 million carats annually. World production of natural diamonds has been about 40 million carats per year from a reserve base of about 700 million carats.

Jan 1, 1982

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By McHenry Mosier

This progress report on a national survey of the use of detachable bits in metal mines covers 10 mines. It presents comparative costs for drilling with conventional and detachable bits, describes the reconditioning of drill steel, and gives various data on rock drilling at these particular mines. Reports to follow will include similar data on drilling at other metal mines in the United States. ACKNOWLEDGMENTS This report is based on costs and data developed and furnished by the operators of the mines visited. The author is greatly indebted to the officials and staff members at these mines for their cooperation and assistance.

Jan 1, 1936

By John B. Knaebel

Hammer machines are now widely used for underground sampling and exploration. Their application to such work can be divided into two classes - sampling and testing with ordinary drilling equipment to shallow depths of 22 feet or less, and "long hole" drilling with heavy machines and special equipment to depths of as much as 250 feet or more. In the first category hammer drills are employed for either of two distinct purposes: first, as a means of checking the results of grab or cut samples or, in certain types of ore deposits, as a substitute for these methods; and second, as a method of sampling the ground 5 to 20 feet beyond existing faces and thus aiding in the control of stoping operations or in the direction of development headings, as the case may be. The deep-hole drill, in the second category, has proved to be a valuable adjunct to the old established methods of exploring, end developing ore, provided it is employed under natural conditions to which it is suited, handled by men thoroughly familiar with the technique of its operations, and used with its possibilities and limitations clearly understood.

Jan 1, 1932

By C. Melvin Lepper

Microseismic energy is generated when stresses accumulated in rock formations are released in the form of fracturing. The acoustic emissions resulting from these rock fractures and movements are detectable as velocity signals in the earth near the energy source. A Bureau of Mines microseismic system that is capable of detecting the acoustic emissions from pit slope movements is described. The digital circuitry incorporated in the system allows a microprocessor program to immediately calculate and present the location coordinates for the seismic energy source in the mine pit wall. This monitoring system is compact, portable, reliable, and relatively inexpensive and rapidly provides accurate information to the mine operators about the stability of a pit slope.

Jan 1, 1982

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By E. R. Palowitch

Coal wasted with mine refuse represents losses in overall recovery of merchantable coal to the mine operator and a concomitant reduction in domestic reserves of available coal. Fraser, Kelley, and Graham3/ in studying the available coal in mine refuse in the Pittsburgh district of western Pennsylvania have estimated that at least 1 ton of mine refuse is produced for each 10 tons of merchantable coal and that 20 percent of this mine refuse might be recovered as salable coal by mechanical cleaning. SUMMARY This investigation dealt with the mechanical recovery of coal from wine refuse by a dense-medium washery employing pulverized mine rock as the dense medium and operating at a rate of 175 tons per hour. Two types of mint refuse were tested: Freshly mined and that .which had been mined 2 years before and piled on a waste dump.

Jan 1, 1955

By A. Aly Selim

This report describes the feasibility of predicting percussive drilling rates by equations derived from statistical regression analysis. The least squares statistical method was used and the analysis was performed both by direct and by stepwise linear regression analysis. The predicted penetration rate is a function of the drill power and the physical properties of the rocks penetrated. The results show promise that the technique may be of value in providing a mathematical model by which percussive drill manufacturers and users can predict the performance of a given drill. Experimental work involved two mining type percussive drills. Penetration data for these drills were determined from nine rocks drilled in the laboratory. Drill work rates (power) were determined in a separate series of experiments. Rock physical properties were measured from diamond-drill core samples taken from the same blocks used for percussive drilling.

Jan 1, 1970

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By Robert H. Bedford

The Rogan-Mallery tin property is in the foothills on the south slope of the Tehachapi Mountains, Kern County, Calif. It was first visited by the senior author in August 1942, and exploration by means of trenching and diamond drilling began in May 1944 and was concluded in August of the same year. Cassiterite, associated with iron-rich gossan, occurs in a limestone roof pendant at places near or at its contact with the underlying granitic rocks. The cassiterite grain sizes range from 20 mesh to 150 mesh. Surface and diamond-drill samples showed tin ranging from traces up to 122.6 pounds per ton. Exploration by the Bureau of Mines included 2,100 cubic yards of trenching and the drilling of 11 diamond drill holes totaling 1,000 feet. Dana Hogan, president of the Rogan Petroleum Co. of Los Angeles, Calif.) brought these projects to the attention of the Bureau of Mines in July 1942, and the following month a Bureau engineer made a preliminary examination in company with Hillard Mallery, of 408 Ruby Street, Redondo Beach, Calif., the man who discovered them.

Jan 1, 1949

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By Maria I. De Rosa

The U.S. Bureau of Mines conducted a study to determine if correlations exist between the chlorine or nitrogen contents of materials and the hydrogen chloride (HCI) or hydrogen cyanide (HCN) concentrations evolved during the thermal decomposition of these materials. Hydrogen chloride, hydrogen cyanide, and carbon monoxide (CO) were found to be the primary toxic gases evolved during the combustion process. The experiments were carried out in a 20-L furnace with 1-g samples. The furnace temperature, rising from ambient, was set at 1,000 °C with an airflow of 10 L/min. The variables measured were the gas loads (milligrams per gram) of HCI, HCN, CO, and CO2 (carbon dioxide); CO and CO2 concentrations as a function of time were also measured. Other variables included the average concentrations of submicrometer smoke particles and particles' average diameter, mass of particulates, sample and furnace temperatures, and sample weight loss. The data indicate that there are significant correlations between the percentage of chlorine or nitrogen contained in the original samples and the HC1 or HCN concentrations evolved during the combustion of the materials. These correlations may be used to predict and evaluate a material's toxic hazard during combustion.

Jan 1, 2010

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By Charles B. Kenahan

The chemical and galvanic corrosion properties of commercially pure titanium, a titanium-manganese alloy, a titanium-aluminum-tin alloy, 2 titanium-copper alloys, and 2 titanium-aluminum alloys were studied. Tests were conducted in synthetic ocean water, tapwater, 1-percent sodium hydroxide, 5-percent ferric chloride, and 5-percent ammonium sulfate solutions, various concentrations of sulfuric and hydro-chloric acids, and 1-percent oxalic acid. All tests were carried out at 35° or 60° C., with a flow of air or helium. Dissimilar metals involved in galvanic-couples experiments were aluminum, magnesium, and stainless steel. Electrode-potential measurements on single (uncoupled) specimens were also measured. Commercially pure titanium and the titanium-base alloys were generally quite similar in their resistance to corrosion, whether alone or in. contact with a dissimilar metal. Contact with the titanium metals caused aluminum and magnesium to corrode by galvanic action. Coupling with stainless steel in sulfuric acid solutions decreased the normal corrosion rate of the titanium metals. Contact with aluminum in air-aerated oxalic acid and 0.1N sulfuric acid solutions resulted in cathodic corrosion of titanium and the titanium-base alloys; however, there were a few exceptions. The copper alloys showed better corrosion characteristics than titanium in certain sulfuric acid solutions but were more susceptible to chemical attack in some hydrochloric acid solutions.

Jan 1, 1958

By Joseph A. Conway

This paper is one of a series dealing with the mining and crushing methods and costs of the nonmetallic industries, prepared under the sponsorship of and in cooperation with the U. S. Bureau of Mines,. The quarrying methods described in this paper are those used at the Monocacy trap rock quarry which annually produces from 450,000 to 500,000 tons of crushed stone. This property is located 3 miles east of Birdsboro at Monacacy, Pa., and is one of the three quarries operated by the John T. Dyer Quarry Co. Throughout the paper an effort is made to explain the various methods used and the cost of operation.

Jan 1, 1931

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960