Search Documents

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By David A. Hill, James R. Wait

This report contains a summary of analytical research on electromagnetic methods of nondestructive testing of cylindrical conductors. The principal objective is to provide theoretical insight to the operation of electromagnetic sensing of the internal properties of wire ropes that are used extensively in mine hoists. An overall review of past work is also included.

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By Daryl R. Tweeton

This Bureau of Mines publication ill scribes present practices of making injection wells for in situ uranium leaching. Casings, screens, drilling fluids, coring, logging, cementing, and developing are discussed with the objective of aiding those who are starting an in situ leaching operation. Improper choices of materials or techniques can result in wells that are either useless or wells that have an undesirably high resistance to injection. Important factors include careful selection of screen slot size, use of logs for choosing the cementing basket depth, proper cementing techniques, and careful choice, use, and flushing of drilling fluids. The information was obtained through observation of well construction and through discussion with in situ leaching companies, drillers, and suppliers.

Jan 1, 1978

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

By David C. Oyler, Hakan Gurgenli, Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By R. K. Guthrie, H. B. Hill

"INTRODUCTION The Rodessa oil field in Marion and Cass Counties, Tex., Miller County, Ark., and Caddo Parish, La., was discovered in August 1930, when a well drilled to a depth of 5,506 feet in Caddo Parish, close to the surface trace of the Rodessa fault, produced gas in commercial quantities. During the next 5 years 21 gas wells were drilled, and a large reserve of natural gas was developed in the high part of the Rodessa structure underlying the Massive Anhydrite member of the Glen Rose formation.In July 1935 oil was discovered on the flank of the structure when a well drilled to 6,048 feet also in Caddo Parish, was completed as an oil well. The discovery of oil in the Rodessa structure initiated art intensive development program of more than usual interest to geologists, engineers, and operators in the petroleum and natural-gas industry. The complex nature of the different reservoirs, the large volume of ""free"" gas under high pressures and temperatures in the upper part of the reservoirs, and the high gas:oil ratios of some of the wells during the early production of oil presented many problems the solution of which taxed the ingenuity of those responsible for the development and exploitation of the Rodessa field.Early waste of gas and resultant dissipation of reservoir energy led to State intervention, which brought about effective regulation of the quantity of gas blown to the air. Oil production from wells producing more than 2.000 cubic feet of gas per barrel of oil was restricted, and oil allowables generally were based equally upon acreage and upon reservoir pressures. Consequently, oil-production statistics of the field are closely associated with gas:oil ratios and reservoir pressures.The primary object of this report is to present factual and statistical data on well performance in the Rodessa field and to show established trends under certain operating methods and practices in high-pressure gaseous reservoirs, which have been carefully developed and outlined by modern technique and exploited under close engineering supervision.The large size of the Rodessa field, it’s fairly well defined gas caps, and a somewhat definite water table in a part- of the oil- and gas-producing region are of special interest and importance in a study of the fluid and energy relationships in reservoirs. Consequently, the results of much of the authors' work in collecting and compiling date are presented in the form of tables, maps and cross sections to show the relative thicknesses of the different oil-and gas-producing members and their permeability and porosity relationships, and, when possible, the variations in stratigraphy are exhibited in cross sections. Results of a detailed analysis of cores from a number of wells also are presented in tabular and graphic form."

Aug 1, 1943

By Miyuki Morioka, Michael J. Griffin

Discomfort, annoyance, or interference with activities due to exposure to vibration is only expected if the vibration exceeds the threshold for the perception of vibration. When there is more than one vibration input to the body (e.g. at the hands, seat and feet), the sensation is first experienced at the location with greatest sensitivity. Knowledge of differences in the thresholds of perception for vibration at the hand, seat, and feet should assist the identification of sources of discomfort caused by vibration. Perception thresholds for vibration have been determined in several studies, but only a few studies have investigated perception thresholds in the horizontal direction for hand-transmitted vibration 1, 6 or whole-body vibration 4-5, and there has been little consideration of perception thresholds for the foot resting on a vibrating surface. This study determines absolute thresholds for the perception of sinusoidal lateral vibration, examining the effect of vibration frequency (8 to 315 Hz for the hand and foot; 2 to 315 Hz for the seat) and the effect of input location (the hand, the seat and the foot). Methods Three groups of twelve males aged between 20 and 29 years participated in the experiment. Subjects in each group attended an experiment to determine perception thresholds for lateral vibration via either a rigid handlebar (30 mm diameter) at the left hand (left hand), or a rigid contoured seat (250 mm x 150 mm), or a footrest at the left foot (30.5 mm x 10.5 mm with 10-degree inclination). For the non-exposed hand (right hand) or foot (right foot), a stationary handle and footrest with the same dimensions as the vibrating handle and footrest were provided so that the same body posture was adopted among the three groups of subjects. An up-down (staircase) algorithm was employed to determine thresholds in conjunction with a three-down one-up rule. A single test stimulus (2.0 seconds) was presented with a cue light illuminated during this period. The task of the subjects was to indicate whether they perceived the vibration stimulus or not. The threshold was calculated from the mean of the last two peaks and the last two troughs, omitting the first two reversals. Results The median absolute thresholds of the 12 subjects determined at each frequency for the hand, seat and foot are shown in Figure 1. A frequency dependence of the threshold contours within the investigated frequency range is evident, with similar shape to the threshold contours

Jan 6, 2006

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

The Bibliographic Data Base contained in the present volume is the result of a literature search conducted as one task of the Bureau of Mines project concerned with research in borehole assay technology. The data base includes articles, symposia, books, corporate and government reports, patents, and other literature concerned with some aspect of borehole logging, from January 1969 through December 1975. Occasional updating to keep the data base current is anticipated. The remainder of the intro¬duction will be devoted to the explanation of the organization of each entry, along with the translation of terms and abbreviations used in the text. Each entry contains six sections. These include an ID code, a title, an author section, a source section, an abstract, and a descriptor section. The first item listed in an entry is the ID code. This serves to identify an entry. It consists of the first six characters of the first author's (or editor if no authors are involved) last name, along with the last two digits of the year of publication. A letter sometimes follows the year of publication to assure a unique alphanumeric code. For example, if an author named Wilson writes more than one piece of literature in a given year (for example, 1972), the ID code for the entries identifying these pieces of literature would be identical. Therefore, to allow for unique ID codes, the first piece would he identified as "WILSON 72,', the second piece as "WILSON 72A", the third "WILSON 72B", and so on.

Jan 1, 1976

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

Chromium, a critical mineral for which the United States is largely dependent on foreign sources, is the subject of a new report just issued by the Interior Department's Bureau of Mines. The report is the first in a new series called "Mineral Commodity Profiles" (MCP's). Designed to give an updated review of important events affecting critical minerals, it also presents a comprehensive description of industry structure, supply-demand relationships, technology, and outlook for the future.

Jan 1, 1977

By N. E. Hanna

An investigation was made of pressure pulses produced by unconfined explosive blasts in underground openings. Four tests were made with TNT or modified amatol charges ranging in weight from 60 to 2,000 pounds; each test involved either single or multiple charges. Pressure-time profiles were obtained using mechanical self-recording pressure gages. The cube-root scaling law for peak pressure was found to be valid within about 1 tunnel diameter; at greater distances, the pressures obtained along direct paths were generally higher than this scaling law would indicate.

Jan 1, 1968

By Thomas M. Barczak

State-of-the-art longwall roof supports provide effective strata control, but failures of these support systems still occur. To identify failure mechanisms and the impact these failures have on the safety of the support system, the U.S. Bureau of Mines has been conducting research on shield mechanics in the Bureau's unique mine roof simulator, as well as field studies of in situ support loading and investigations of longwall failures, Three types of failures are discussed: (1) inadequate support capacity, (2) structural failure, and (3) instability. Hypothetical situations with proposed courses of action and case studies of actual longwall failures are described. This information is intended to assist the Mine Safety and Health Administration (MSEIA) and industry mining personnel in safety evaluations of longwall roof support systems.

Jan 1, 1989

By Joe Maher

[ ]

Jan 1, 1976