Search Documents

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By E. D. Gardner

During the summer of 1935 a plan was proposed by which the Government should establish custom sampling plants for gold and silver ores in the mining districts of the West, where the construction of such plants would be justified as an unemployment relief measure. It was known that in many districts prospectors and small operators had small lots of smelting ore that could not be marketed for lack of sufficient capital to get out enough ore at a time to make carload shipments to distant smelters. Moreover, considerable ore of milling grade was available in many districts in which there were no custom milling facilities. It was felt that. accurate sampling and the classification and consolidation of small lots of ore produced from prospects and small mines, with quick cash returns to the shippers on a nonprofit basis, would stimulate the working of small gold and silver properties: Idle mines would be put to work, and there was a possibility that some of the prospects could be developed into regularly producing mines. Each sampling plant was to be centrally located so as to serve the greatest possible number of mines and prospects. Wherever possible, the plants were to be built on a railroad, is ore of smelting grade accumulated, it was to be shipped to a smelter in carload lots. Where a plant was not on a railroad, smelting ore was to be trucked to the railroad after being sampled.

Jan 1, 1936

Operator efficiency and control capability along with cost effectiveness have been the quest of mining, industrial, and mobile hydraulic engineers for years. The majority of the functions in present day fluid power systems are controlled by on/off control valves. They are inexpensive and provide easy installation and operation, but they lack the quality of fine control of load flow or what is sometimes known as "feathering the load". An alternate approach to obtaining this capability is the use of electro-hydraulic servo-valves, but their implementation into a system is complex, and they are expensive. As a result, electrohydraulic systems are still used primarily in the aerospace industry. Of late, a compromise seems to have evolved between the on/ off control systems and the servo-technology is the so-called proportional flow control valves. A proportional flow control valve meters fluid to the load in proportion to the input command from the operator. In principle, it is similar to a conventional flow control valve and is tailored to meet the control requirements from the load point of view. The hydraulic system using this valve usually works in an open-loop mode with the operator closing the loop. Incorporating load-sensing mechanisms and adoption of electrical/electronic signalling into the valve make it the "ideal valve" which designers have been looking for from a techno-economic point of view.

Jan 1, 1983

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By G. T. Krempasky

In an attempt to develop a suitable precast concrete support for underground use, two different models (1955 and 1958) of a five-piece concrete set were designed, fabricated, and tested under adverse loading conditions. Model 1955 was designed to withstand an ultimate, uniformly distributed, vertical load equivalent to what a three-piece, 12- by 12-inch wood set of intermediate-grade Douglas fir would withstand. A design figure of 138,000 pounds for the vertical load was used on both the 1955 and 1958 models. In addition, the 1958 model was designed to withstand a uniform horizontal load of 7,000 pounds per foot and additional concentrated-point loading. The step- by-step design of each model is presented in the appendixes. A series of five destruction tests was conducted underground on the 1955 model, and results of the tests showed that the type and method of blocking were of major significance.

Jan 1, 1963

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By Liming Yuan

A study of the ignition of non-fire-resistant hydraulic fluid sprays was conducted by the National Institute for Occupational Safety and Health. Both an open flame and a hot steel surface were used as the external heat sources. With the open flame as the heat source, the minimum oil temperature and minimum spray nozzle pressure that resulted in an ignition were measured. The effects of the distance between the open flame and the nozzle and the nozzle orifice diameter on the ignitability of the hydraulic fluid sprays were examined. With the hot surface as the heat source, the minimum surface ignition temperature was determined. The degree of oil atomization and the relative direction of oil injection with respect to the hot surface are discussed. The ignition of oil sprays from the impingement of oil jets onto a vertical surface was also investigated. Finally, the results are compared with those obtained for fire-resistant hydraulic fluids. Keywords: Ignition; hot surface; open flame; hydraulic fluid

Jan 1, 2006

By B. F. Naylor, C. H. Shomate, F. S. Boericke

"Ilmenite is the most important titanium-bearing constituent of titaniferous iron ores. Such ores, of which the United States has abundant reserves, are of interest because they constitute an important potential source of both iron and titanium that may be tapped in times of stress, and which eventually may be utilized in the normal course of events.As the iron and titanium constituents of titaniferous iron ores are not completely separable from each other by ore-dressing methods, any process for metal recovery will, of necessity, involve reduction of the iron in ilmenite. Consequently, knowledge of the thermodynamic properties of ilmenite should supplement information already available concerning those ores. With this in view, the Pacific Experiment Station of the Bureau of Mines undertook to evaluate thermodynamic properties; the data obtained are the subject of this report.Three types of experimental work were involved. First, low-temperature specific heats of ilmenite were measured in the temperature range 500 to 29S° K. These data serve to evaluate the entropy, a quantity necessary for a reliable evaluation and correlation of other thermodynamic properties. Second, high-temperature heat-content measurements were made in the temperature range 298° to 1,743° K. The data serve to bridge the gap between room temperature and elevated reduction-process temperatures. Finally, hydrogen-reduction equilibria were measured in the temperature range 1,220° to1,375° K. These data-give a direct measure of the free energy of reduction of ilmonite at these temperatures and, in conjunction with results of the other two types of measurements, serve to obtain the heat of formation of ilmenite, a quantity not readily determinable by direct calorimetric means.The data are correlated to form a composite, self-consistent portrayal of the thermodynamic properties of ilmenite, which may be used in evaluating the efficacy of any reducing agent of known thermodynamic properties. Selective-reduction of iron in ilmenite by hydrogen, carbon monoxide, and carbon are considered in this report."

May 1, 1946

By W. W. Adams

The United States Bureau of Mines, in cooperation with the National Send and Gravel Association conducted a safety contest in 1929 Among producers of sand and gravel. Only 26 plants were enrolled, as the contest was late getting under way. It is hoped that a ranch larger number of plants will be represented in the safety competition of 1930. Two trophies, both of which were provided by Rock Products magazine, were awarded at the end of the contest; one trophy was given for the best safety record among plants working 100,000 or mare man-hours during the year and the other for the beat record among plants working less than 100,000 man-hours. The trophies were presented to representatives of the winning, companies on January 29, 1930, at the annual convention of the National Sand and Gravel Association at Memphis, Tenn.

Jan 1, 1930

The 1967 Lignite Symposium was held at Grand Forks, N. Dak., on April 27-28, 1967. This was the fifth of these technical meetings and the fourth which was cosponsored by the University of North Dakota and the Bureau of Mines. These symposia have provided a meeting place where current developments concerning technology and utilization of solid fuels (lignite) are presented. There was a registration of 255 persons from 24 States, the District of Columbia, six Canadian Provinces, Germany, and India. Many segments of coal or energy oriented organizations at many levels were represented. During the meeting, 18 presentations were made covering developments in electrical power generation, mining, estimation of reserves, combustion, gasification, and chemical and speciality uses of low-rank coals; these are com-piled in this Information Circular to provide a record of the symposium and to permit wider dissemination of the information. Proceedings of the other meetings have also been published.3

Jan 1, 1968

By E. P. Dowding, J. Schlocker, C. H. Fuchsman, R. R. Lloyd, Mahan. W. M., O. C. Garst, W. T. Rawles

"INTRODUCTION The United States, although the leading consumer of chromite, depends almost entirely on imports for its supply. For instance, the consumption during. 1941 amounted to 714,645 long tons, whereas the domestic chromite production, although the highest since 1918, was 12,731 long tons or only 1.78 percent of the domestic consumption. 9/ Domestic production was tremendously, accelerated,after 1941 by war demands; however, only a small proportion of this domestic product was of sufficient quality to be substituted for the high-grade imported chromite demanded for metallurgical purpose. Chromite is used largely for making ferrochromium, an alloy containing 60 to 70 percent chromium which is used in making alloy steels. Peacetime specification for ferrochromium required that it should contain 68 to 69 percent chromium. These specification were lowered to between 60 and 63 percent, chromium in 1941 to permit the use of lower-grade ores. The specifications for metallurgical chromite, used for making ferrochromium, were established first by the Metals Reserve Company at 48 percent Cr203 and a Cr. Fe. ratio of 3 : 1 but later were lowered to 45 percent Cr203 and a Cr : Fe ratio of 2.5 : 1. The ratio of chromium to iron in chromite is important, because the contained iron enters the alloy in making ferrochromium and, although an ore may contain the required 45 percent Cr203, it may contain too much to be suitable for ferrochromium production. The principal sources of domestic chromite are California, Oregon, Montana, and Alaska minor, small, and widely scattered deposits in another dozen States. Without exception, these deposits are low-grade, require beneficiation to produce a commercial product, and are not competitive with imported high-grade ore in normal times. Nevertheless, these deposits form strategic reserve, which must be utilized in periods of national emergency. Recognizing this fact; the Bureau of Mines for many years has undertaken investigations to develop methods of utilizing domestic chromite ores. The problem has been approached from three angles: (1) Mechanical methods of concentration; (2) beneficiation by chemical or metal¬lurgical methods; and (3) production of metallic chromium by electrolysis of solutions prepared from ore or concentrate."

Feb 1, 1946

Prier to the date of this contract, Ocean Energy had developed and demonstrated a high efficiency fluorescent caplamp which operated from a standard 4 volt miner's caplamp battery. This unit produced about five times the light output of the standard incandescent miner's caplamp. The Company believed that the major market for this unique caplamp was in the industrial and municipal applications. Because of the additional safety requirements for coal mining use, and in conjunction with the much smaller market in the mining industry, the additional expense and difficulty of modifying this caplamp to comply with the Federal and State coal mine regulations were not considered at that time. Recognizing the potential of this lamp for improving illumination conditions for underground coal mining, the US Bureau of Mines contracted with Ocean Energy to make the required modifications to this lamp to bring it into compliance with the Federal and State of Pennsylvania regulations, and thereby, make this lamp available to the anthracite and bituminous coal mining industry. At the outset of the contract, the injection molds for the caplamp housing were being completed, and only prototype, hand fabricated, units were available for tests. The Bureau evaluated these prototype units and formulated a performance specification for the miner's version. Light level and distribution, weight, size, angle of tilt, and operating duration were all specified. In addition, it was required that the caplamp be com¬patible with existin charging equipment at the mines and that the final design be in full compliance with MESA Schedule 6D and he ultimately approved by MESA, Approval and Testing, as well as by the Pennsylvania Bureau of Deep Mine Safety. The scope of this contract covered the modifications required to achieve these objectives. It was agreed by the Bureau that all rights to the lamp, including design, material combinations, circuitry, etc. would remain with Ocean Energy. The charger/adapter system and components, which were developed under contract funds, are disclosed hero and become public knowledge and property. Patent applications have been filed by Ocean Energy to protect the mechanical and electrical design aspects of the lamp. It should be noted that this report contains details, designs and data which may be covered by one or more Ocean Energy patent applications, and disclosure herein is made only to provide better understanding of the contract results.

Jan 1, 1975

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite. During the early years of these plants little success was anticipated from the use of bituminous coals and lignites, but in 1904 and 1905 it was fully demonstrated at the Government testing station at St. Louis that these fuels could be utilized to excellent advantage. However, although many producer-gas plants in daily operation are using bituminous coal and lignite, many power-plant men are still skeptical regarding the successful commercial use of these fuels.

Jan 1, 1916

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary. The strategic minerals investigations of the bureau afford an example of this change in emphasis to problems of immediate and urgent interest, and during 1941 they comprised, upon the basis of appropriations and expenditures, more than 90 percent of the work of the division.

Jan 1, 1941

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By A. C. Johnson

The Bureau of Mines explored the Three Kids deposit in 1941 as part of a strategic minerals program. Earlier mining and exploration had established the presence of a substantial tonnage of medium-grade wad ore, and drilling and sampling by the Bureau of Mines, in collaboration with the Federal Geological Survey, indicated an additional tonnage such that development and exploitation became more clearly feasible. Private interests, with Government support, undertook to produce metallurgical-grade manganese. The present paper describes the Bureau of Mines exploration and subsequent development. Manganese in the Three Kids area is found in one of the lower members of the Muddy Creek formation in a bed of fine sandstone and silt, which outcrops around the north edge of the River Mountains and generally dips 20° to 40° away from the hills. There is considerable variation in the thickness and grade of the ore. The ore is light weight, having a density of 1.2 to 2.

Jan 1, 1956

By G. A. Bole

"This paper presents a review of the literature and is an epitome of work acne and articles published by Schurecht, Robson and Andrews', in the investigation of the feasibility of making basic refractories from dolomite, was carried on successively by these men, at the Ceramic experiment Station of the Bureau of Mines, Columbus, Ohio.Scope of the work.The dolomite refractories investigation of the Ceramic Station includes a study of the many fluxes which could be used to aid in the dead-burning of dolomite and also a complete survey of the iron oxide-alumina-silica field as fluxes. The temperature of calcination and the resulting properties have been carefully investigated, and the most desirable calcines chosen for further investigation in the making of dolamite bricks. Many binders and the several methods in common use of fabricating bricks commercially were tried, and a thorough study was made of the properties of the most successful ware,Previous Investigators.Even before the World War, considerable work was done on dolomite this war greatly accelerated the efforts of the many Investigators."

Jul 1, 1924

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949