Search Documents

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

By W. Timothy Adams

The production of natural abrasives varied in quantity and value compared with 1976. Output of tripoli-type materials was approximately the same in both quantity and value. Special silica stone products decreased in quantity and increased in value. Garnet production decreased both in quantity and value. The production of emery increased and the production and value of manufactured abrasive material was approximately the same. Foreign Trade Imports of abrasive materials were 23% more in value than in 1976, and exports plus reexports increased in value 10%. Net imports, the excess of imports over exports and reexports, were $35.3 million. The volume and value of all abrasive materials exported varied.

Jan 1, 1980

By L. M. Burman

The phase-boundary pressure required to maintain a natural hydrocarbon fluid in a single phase must be considered in planning the recovery of reservoir liquids by miscible-phase processes. The change in the phase-boundary pressure at reservoir temperature that results when a light component or a mixture of light components is added to a reservoir fluid is an especially important consideration. The cricondenbar pressure (maximum phase-boundary pressure) and the critical pressure are unique correlated pressures that have been utilized to calculate the change in phase-boundary pressure that may result when the composition of a reservoir liquid is altered by an additive. In this study one reservoir oil and three gas-condensate fluids are used as examples. Correlations pertaining to the critical and cricondenbar states in chapters 4 and 5 of Bureau of Mines Monograph 10 (3)5 were used to demonstrate how butane and lighter components added to these reservoir fluids affect their phase-boundary pressures.

Jan 1, 1962

By Donald W. Mitchell, John Nagy

Observations made on coking of coal, deposition of soot, dust transport, flame, violence, and related phenomena following experimental coal-dust explosions are summarized. Data are given on gas explosion pressure, flame length, flame velocity, and variation of these parameters with concentration. Conclusions from these observations are useful in preventing similar occurrences in operating mines and serve as a guide in improving safety.

Dec 1, 1963

By Norman G. Foster

The mass spectra of four tertiary butyl substituted thiophenes are reported. A comparison and contrast with earlier structure correlations made by API-RP48 mass spectroscopists is presented. The fragmentation routes of these types of molecules are discussed and explained in terms of existing theories in mass spectrometry. Low ionization voltage data are presented to support the mechanistic picture developed. Structures are inferred about some of the ions, and these are correlated with existing theories. Metastable peaks in the spectra are used to support the fragmentation paths. The presence of doubly charged ions in the spectra is noted and the possible implications toward mechanisms discussed. The general picture of simple, small fragments leaving the ion moiety upon further fragmentation is developed in detail. Some suggestions are presented for further work utilizing isotopically labeled molecules to establish firmly the general picture of fragmentations of the alkylthiophenes.

Jan 1, 1966

By C. M. Harrer

The location, features, qualities, and extent of iron occurrences and the associated resources--limestone and dolomite, bentonite, coal-lignite, petroleum and natural gas, power, and water--are evaluated. The results of pioneer beneficiation tests on South Dakota taconite are discussed. In addition, pertinent features of taconite development, cost factors, the Western and Central United States trade area and markets are reported. The State's production of iron ores until 1963 has been small and for purposes other than the manufacture of iron. This investigation disclosed the probability of large resources of taconite in Pennington and Lawrence Counties. The average iron content is 29 percent, and a 65-percent or better iron concentrate might be produced. Ample resources are available for mining and processing taconite. An investment of at least $26 million would be required for a plant capable of turning out 1 million tons of agglomerated iron concentrate per year. The feasibility of such an enterprise is indicated, but intensive investigation and research must be completed to justify such an investment.

Jan 1, 1966

By D. K. Ingram

In situ horizontal stresses were measured to determine the influences of geologic anomalies on the regional horizontal stress field in two coal mines in southern Illinois. Stress measurements were obtained near a normal fault having a 121-ft displacement at the AMAX Wabash Mine and a large coalbed want at the Kerr-McGee Galatia No.5 Mine. Horizontal stress measurements were completed using a Bureau of Mines borehole deformation gauge. The average maximum and minimum horizontal compressional stresses at the Wabash Mine were 1,400 and 800 psi, with the direction of maximum stress ranging from N 78° W to N 83° E. At the Galatia No.5 Mine, the averages were 1,500 and 500 psi, with the direction of maximum stress ranging from N 85° E to N 75° E. Generally, the geologic anomalies appear to have no dramatic effect of the regional horizontal stresses. However, subtle differences between stress measurements suggest an influence by the fault zone at the Wabash Mine. The larger anisotropic stress conditions at the Galatia No.5 Mine could be responsible for the increase in kink zones and directional roof failures.

Jan 1, 1988

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

Significantly increase the amount of fresh air that sweeps the face in front of a continuous mining ma-chine, in order to prevent methane gas buildup. Approach Water sprays are mounted along the sides of a continuous miner and behind the cutter head to help push ventilating air along the required path, and prevent its short circuiting. How It Works A continuous miner is fitted with two sets of water sprays, one of which is used at a time. The set of sprays shown in the diagram, helps move the ventilating air forward along the left side of the miner and across the cutter drum from left to right. That air is then drawn into the exhaust air passageway located along

Jan 1, 1978

By Frank E. Cash

The Bureau of Mines in its safety work has for a number of years advocated and recommended the use of permissible portable electric cap lamps for use in all mines. In the course of time required for the evolution from an unsatisfactory to an efficient and safe light, but encouraging increase in their use has been experienced in Alabama. As early as 1916, small installations of these safer lamps were made or an experimental basis by several operating companies, and the first complete mine installation eras made at the Virginia mine of the Gulf States Steel Co., July 1, 1918. From the experiments in 1316 and the complete equipment of the first mine in 1918 gradual progress has been made until there are now 30 installations with 10 operating companies; as a result 20 mines have been put entirely and 5 partly on, closed lights, and 3 companies equip their engineering departments; two installations of closed lights are maintained by other companies for emergency use. One of the mines partly on the electric cap lamp is an ore mine - the only one in Alabama (and one of the very few in the United States) that uses closed lights. ACKNOWLEDGEMENTS The full cooperation of operating officials, lapmen, and lamp representatives was given in the collection of the data in this report, and is hereby acknowledged.

Jan 1, 1928

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By Whitman E. Brown

"As part of a Nation-wide program of the United States Government to develop natural resources, funds were made available to the Bureau of Mines for the investigation of the ""Reduction of Iron Ores by Solid and Gaseous Fuels."" These investigations are concerned with the direct production of iron from its ores without the use of a blast furnace. Many processes have been proposed for the low-temperature reduction of iron oxides, but few have been developed to commercial use. High-quality sponge iron is produced com-mercially only in Sweden.The cost of iron production depends in part on the grade of the ore and increases with decrease in grade. The substitution of cheap natural gas in a sponge-iron process for expensive coke in smelting in the blast fry pace would partly compensate for the use of low-grade ores. If a process can be developed in which inexpensive natural gas can be used as fuel and reducing agent, the large deposits of low-grade iron ore and the natural-gas resources of east Texas may be utilized in the commercial production of sponge iron.Sponge iron may possibly be used to supplement scrap iron, pig iron, or, in special instances, wrought iron. Sponge iron will vary but slightly in composition and will contain little or no nickel, cobalt, manganese, copper, and other allowying metals. It is becoming increasingly difficult to obtain choice scrap iron of nonalloy composition. Pig iron contains 1.5 to 3.0 percent silicon and 3.0 to 4.5 percent carbon. Sponge iron generally contains less carbon than pig iron.The Madaras Steel Corp. in Longview, Tex., built a set commercial-scale sponge-iron plant which was intended to be operated in connection with a steel foundry. The process is based upon the reduction of preheated iron ore, with hot reducing gases under pulsating pressure. Although the Madaras Corp. had previously experimented with the production of sponge iron by reducing the ore with pure hydrogen, several attempts to use a re-formed natural gas as the reducing agent in this pilot plant were unsuccessful. The Bureau of Mines leased this plant and conducted an extensive investigation of the Madaras process on a semicommercial scale.The experiments were not entirely satisfactory, partly because of mechanical difficulties and partly because the reducing gas was not of the best quality. However, much information on the production of reducing gas by re-forming natural gas and on the reduction of iron ore with re-formed natural gas was obtained.The sponge iron produced contained approximately 0.1 percent phosphorus; and, after melting in an electric furnace, the iron contained approximately 0.15 percent phosphorus. The results of attempts to improve the ore by ore-dressing methods were not encouraging."

Aug 1, 1946

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By Norma R. Golumsic

Gasoline and other liquid fuels may be obtained from coal by direct and indirect hydrogenation.3/ The direct process, usually termed the coal-hydro-genation or the Bergius process, was patented in Germany by F. Bergius in 1914 and developed to a commercial stage by the inventor and I. G. Farben-industrie. From a chemical point of view, the coal-hydrogenation process consists of adding hydrogen to the complex coal molecules and removing oxygen so that its chemical constitution is changed to that of petroleum, whereupon the coal substance liquefies, yielding an aromatic crude oil. In the indirect-hydrogenation process, known as the Fischer-Tropsch process (invented by Franz Fischer and Hans Tropsch in Germany), coal, lignite, or natural gas is first converted to water gas, a mixture of carbon monoxide and hydrogen. This mixture of gases, in proper proportion and after suitable purification, is then passed over a solid catalyst at relatively low pressures (1 to 20 atmospheres) and temperatures ranging from 180° to 260° C. The products obtained are gasoline, Diesel oil, liquefiable gases, and paraffin wax.

Jan 1, 1946

By Sidney Katell

This report, covering the period January 1969 through December 1969, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the 11th in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost. Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing.

Jan 1, 1970

Overexposure to noise is a widespread, serious health hazard in the mining industry, and causes hearing losses to a large percentage of the mining population. Recognizing this fact, the Bureau has a major on-going research effort to address this problem area. These proceedings include an overview of the Bureau noise control program and summarize nine selected noise control research programs.

Jan 1, 1984

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors' quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By F. G. Schwartz

The Bureau of Mines developed a rapid and precise method for predicting storage stability of motor gasolines. This method resulted from the investigation of many analytical techniques as well as a study of fuel composition and fuel component gum-forming mechanisms. The first section of this bulletin discusses the development of the prediction test through its several phases, including revision of the standard 110° F storage test; attempts to develop a modification of the ASTM D525 induction bomb test; and the ultimate abandonment of this procedure with the adoption of the 16-hour oven test that was both precise and rapid. The second section comprises a discussion of further studies of fuel com- position, including the reactivity of certain sulfur compounds and hydrocarbons to form gum. The compositions of various gums and inorganic deposits are reported in terms of elemental analysis and spectroscopic examinations. The reactions of tetraethyllead with selected hydrocarbons are also reported.

Jan 1, 1972

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009