Search Documents

By Øystein Sture, Kurt Aasly, Ben Snook, Sigurd A. Sørum

INTRODUCTION Efficient exploration methodologies for base metal deposits have huge benefits for future deep sea mining endeavours, and underwater hyperspectral imaging (UHI) has been variably demonstrated to have applications in the identification and characterisation of mineralisation on the seafloor for both nodules and seafloor massive sulphides (SMS) (Dumke et al., 2018 and 2017 respectively). Due to growing resource requirements (Singer, 2017), SMS deposits are considered to be increasingly significant sources of copper and zinc, as well as silver and gold. This style of mineralisation is currently occurring at active hydrothermal vents (black and white smokers) but now-inactive sites also have the potential to be large mineral deposits. As such, the development of novel methodologies to detect both on-going and extinct mineralisations are of high importance. Geological setting During the MarMine cruise (Ludvigsen et al., 2016), non-mineralised host rock, low grade ore and high grade ore grab samples (Snook et al., 2018) was collected by ROV from the Loki’s Castle deposit (Pedersen et al., 2010), located on the Mohn’s/Knipovich junction on the ultra-slow spreading Arctic Mid-Ocean Ridge (AMOR), at a depth of approximately 2300 m. This material has been characterised as part of the MarMine project (e.g. Snook et al., 2017), and, by imaging compositionally constrained material, the measured hyperspectral responses can be used to generate a library for identification of deposits on the ocean floor. UHI technology Remote sensing with hyperspectral and multispectral technologies has seen wide use in prospecting for ores and hydrocarbons on land (Van der Meer et al., 2012). Iron oxides and sulphides have low blue reflectance and high red reflectance in the visible spectrum. The ratio between these two pairs has been used in exploration for terrestrial deposits of hydrothermal origin (Sabins, 1999). This discrimination typically also includes wavelengths exceeding the visible spectrum (1.5µm – 2.5µm). These wavelengths are typically not utilised underwater because infrared wavelengths and higher are rapidly attenuated in water. However, discrimination based on the full shape of the spectral response in the visible light (350nm – 800nm) may still be possible (Bolin and Moon, 2003). Resolving the endmembers from the spectral responses requires prior knowledge about the optical properties of the materials, i.e. their reflectance. These reflectances can be obtained in a controlled environment, where the spectra of the lamps, wavelength- dependent attenuation in water and scattering of light can be accounted for (Johnsen, 2013).

Jan 1, 2018

The Brothers hydrothermal system is host to two very contrasting vent fields and to date, is the only known example of this kind for any submarine arc volcano in the world. Firstly, there is the NW caldera field. It is perched on the caldera walls and is up to 1,200 years old, and represents a more ?mature? system dominated by water/rock interactions, though there is also evidence for magmatic contributions to the hydrothermal fluids. It is host to relatively high temperature (~300°C), focused venting of metal-rich fluids. Large Cu- and Zn-rich sulfide chimneys occur at this site, with high concentrations (up to 90 ppm) Au apparent in some chimneys. Vent fluids of the NW caldera site show sub-seafloor phase separation is occurring at this site. Silica concentrations in these vent fluids are consistent with the vent fluid temperatures. Secondly, there is the cone vent field that is much younger, and which sits atop the summits of a main cone (the Upper cone) and an adjacent satellite cone (the Lower cone) that occur inside the caldera, near the southern caldera walls. This field is dominated by S-rich vents with vent fluids more diffuse, lower in temperature (<120°C), very gassy and acidic (to pH 1.9), and relatively metal-poor. Fluids of the cone site have Mg and SO4 concentrations higher than seawater values, indicating these ions have been added to the hydrothermal fluid and are not being depleted via normal water/rock interactions. Variability occurs between the two cone vent fields, with the diffuse discharge observed at the Upper cone volumetrically small and chemically different from the Lower cone. For example, from the vent fluid Mn, Li, Rb, and Cs concentrations, it is apparent that the Lower cone has experienced a lower degree of water/rock interaction (i.e., more reaction) than the Upper cone. Vent fluid pH is higher for Lower cone, consistent with more reaction and neutralization of acidic gases. Fe/Mn is lower at the Lower cone due to decreased Fe solubility at the higher pH. The lowest pH sample (1.9) is from the Upper cone that has 39.4 mmol/kg of SO4, consistent with input of magmatic SO2 and disproportionation to sulfuric acid and S or H2S. Thus, the Upper cone site could be interpreted to have a shorter reaction path and residence time between the point of magmatic degassing and the seafloor venting than the Lower cone site. Isotopic compositions of the NW caldera and cone vent fluids show evidence for magmatic water with negative dD and d180 values, while 3He/4He values show the Brothers hydrothermal system has shifted towards more magmatic conditions over the past several years with both sites affected by magmatic events. Similarly, vent fluid sulfide d34S values and those for sulfide minerals from NE caldera chimneys also indicate disproportionation reactions involving magmatic SO2. Minerals such as chalcopyrite, bornite, chalcocite, covelllite and euhedral grains of hematite occurring in high temperature chimneys from the NW caldera site are consistent with a more oxidizing, magmatic fluid, while bulk sulfide geochemistry data show evidence for a higher temperature suite of elements (e,g., Mo, Co, Se) associated with Cu-rich chimneys. Gold mineralization occurs in these high temperature chimneys and is associated with the most recent deposition of high concentrations of Cu, where d34S values are most negative. Geophysical evidence suggests that the top of a magma chamber occurs ~2.5 km below the caldera floor, beneath the cone site in the SSE quadrant of the volcano. Very low velocities of <1 km-2 are seen in the seismic data between the magma and the seafloor, and are indicative of gas release. Harmonic tremor data provide evidence for a 500 m pipe-like ?conduit? located above the magma chamber (and below the cone), linking it with the overlying hydrothermal system, providing a mechanism for magma-derived metals to enter the hydrothermal system under the cone site. The NW caldera and cone sites are considered to represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members.

Jan 1, 2010

By William D. Siapno

Approximately a century lapsed between the time nodules were discovered and the beginning of commercial exploration in the early 1960&apos;s. A period of rapid development of exploration and mining technology ensued over most of the next two decades. In recent years advancement has been sharply curtailed. This paper discusses the constraints inhibiting nodule mining and some developments that could aid in overcoming certain difficulties. Specifically, the greatest single constraint is economic. With few exceptions mineral markets are badly depressed. Present projections for development of nodules are for the late 1990&apos;s or beyond. However, the U.S. awarded exploration licenses in mid-1984 and more recently boundaries of license areas have been released. These conditions promote cooperation among organizations engaged in deep ocean mining. Survey data, and where appropriate some data products, have been exchanged between various consortia. The present hiatus in at-sea activities provides an excellent opportunity to investigate the best means to proceed. This period of quiescence offers a rare moment to distill the meaningful values of an era of hectic activity to permit more efficient development in the future.

Jan 1, 1985

By Brian D. Bornhold

A comprehensive multi-disciplinary marine geological survey of northwestern Graham Island, Queen Charlotte Islands, British Columbia, Canada was conducted by Offshore Survey and Positioning Services Ltd. of Vancouver, B.C. on behalf of the Geological Survey of Canada; Energy, Mines & Resources Canada, Pacific Geoscience Centre, Sidney, B.C. Canada during October 1984 and July 1985. The aim of the survey was to map both the surficial geology and geomorphology in order to identify and evaluate the nature of the nearshore sedimentation and recent tectonics including stability (slumps and scarps) seafloor faults (frequency and displacements) and both the classification and consistency of soil type boundaries and properties. Data was acquired by utilizing conventional indirect applied marine geophysical techniques including side scan sonar, precision echo sounding and complimentary soil sampling. During October 1984 a total of 320 line kilometres of data including 180 soil samples were acquired. During July 1985 a total of 300 line kilometres of data were acquired including 150 soil samples.

Jan 1, 1985

By D. S. Cronan

Mineral exploration problems in the S.W. Pacific are not unique to that region, but a combination of favourable circumstances render it an ideal area to attempt to solve such problems. The land area of the S.W. Pacific island nations is only a fraction of the total sea area they can claim under current International Law. Hence, they have a great need to explore and evaluate their offshore areas. For the past ten years the focus of this work has been CCOP/SOPAC which has individually and jointly with other groups initiated and maintained far reaching marine mineral exploration programmes. In association with CCOP/SOPAC the writer has obtained and analysed approximately 650 sediment samples from the S.W. Pacific region for seventeen elements. Multivariate statistical techniques have been applied to the data set. The aim has been to identify chemically anomalous sediments reflecting either sea floor mineralisation and/or mineralisation on adjacent land areas.

Jan 1, 1985

By Elizabeth McIsaac, Wylie Spicer

"In July 2016 the International Seabed Authority (the “ISA”) released a first working draft of its mineral exploitation regulations as well as the standard contract terms for mineral resources in the Area, for which stakeholder input was sought in late 2016. In January of 2017 the ISA released a discussion paper on environmental matters related to these draft regulations. The ISA is now in the process of further developing its draft exploitation regulations and standard contract terms to ensure that seabed mining is carried out in an environmentally sound way for the common benefit of mankind.As the regulator of the “Area”, the ISA can draw lessons from onshore mining regulators and offshore petroleum regulators for their experiences in legislative drafting to smoothly and safely oversee project development, implementation, and closure. However, one of the unique challenges that the ISA faces in regulating private industry is its status as an international organization and not a sovereign nation, which results in a significantly different legal relationship between the regulator and the regulated. The result is that the exploitation contract is the sole legal connection between the mining proponent and the regulator for the exploitation phrase of the project.Accordingly, in the regulatory development process, the ISA must carefully consider which rights and obligations are set out in the exploitation contract versus the regulations. This decision will dictate the flexibility the ISA will have to modernize the conduct required of mining proponents in response to changing best practices in the industry, technological progress, and advances in the understanding of the marine ecosystem. As the first working draft of the exploitation regulations sets out an initial contract period of twenty years, it is crucial for the ISA to carefully consider the rights, obligations, and procedures it agrees to in the exploitation contract, as unilateral amendment will not be possible after contract execution."

Jan 1, 2017

By B. Prause

Ferromanganese crust samples collected from Central Pacific sea-mount areas became of special interest after surprisingly high nobel metal contents have been analyzed. Hydrogenetic crust growth is controlled by the conditions of the oceanic water column. Thicker encrustations show two crust generations of different age ranges. The mean values of the chemical composition state that the older generation is richer in P, Ca, Ni, Cu, Zn, and Pt and depleted in Fe, Ti, Co, Al, and Si. The differences apparently indicate a distinct change of the geochemical environment. The Pt concentrations vary up to 1800 ppb and do not clearly correlate to one of the other metals. This might indicate a bond of multiple nature. Several mechanisms have been proposed to explain the Pt concentrations in ferromanganese samples. Our models consider seawater and cosmic spherules as responsible Pt sources. In seawater the main species of dissolved Pt probably exist as the doubly negatively charged tetrachloro-complex. A precipitation of Pt in seawater may take place if the chloro-complex is decomposed by reduction of pt2+ to pt0. On the other hand, the Mn02 precipitation is caused by an oxidation of Mn2+ which is supplied from the oxygen-minimum zone. The large activation energy needed for the oxidation of divalent ~n" in solution has been recognised, and the resulting slowness in the formation of Mn(V1)-oxihydrate sug

Jan 1, 1989

By James C. Barker

Concern over the availability of domestic critical and strategic mineral supplies has led the Bureau of Mines to evaluate the reserve development potential of alternative sources in Alaska. Near the village of Platinum, on the southwest Alaska coast, the Red Mountain concentrically zoned ultramafic complex is a source of onshore alluvial placers containing platinum-group-metals (PGM). It has long been suggested that valuable placers may also underlie the shallow coastal waters of the Bering Sea. A direct correlation of placer PGM and chromium to ultramafic rocks in the area was studied by the Bureau and the extent of the complex was mapped. Magnetometer and gravity data and geological studies suggest the complex is a large lensoidal body trending several kilometers offshore to the southwest with a probable steep southeasterly dip. Multiple Pleistocene glaciations and marine transgressions have eroded the western and southwestern portion of the complex. Sediments containing PGM, chromium, and associated gold (largely derived from glacial till) have been transported northward along the advancing coastline by littoral currents. Beyond the breaker zone, these sediments are generally buried by recently winnowed sand and gravel transported by strong longshore tidal currents. There is also evidence that paleoplacer channels underlie the marine sediments.

Jan 1, 1986

By Tracy Shimmield

Deep sea tailings placement (DSTP) techniques have been pioneered in Papua New Guinea (PNG): a mining reliant economy in a seismically active region, facing major environmental challenges in the safe handling and storage of mine tailings on land. Scientists at SAMS have researched impacts of DSTP on the marine environment specifically to inform and develop guidelines for the use of DSTP to reduce environmental impact, thereby lowering risk and increasing private sector investment. Guidelines have been established as regulation by the PNG Government providing reassurance to private investors, facilitating an increase in mining exports to 60% of total export. Researchers investigated the effects of DSTP at 2 PNG mines: Lihir Gold Mine which has been actively discharging tailings since 1996 and Misima Mine, closed in 2004 after discharging tailings for 15 years, allowing an assessment of the recovery of the marine environment after tailings placement. Research involved investigating ocean currents and mixing, the behaviour of metals and the effect of tailings on benthic communities including the risk of elevated metal contents entering the food chain. The research established a metal ?fingerprint? of tailings compared to natural sediments, which enabled the transport of fine tailings within the deep ocean to be ascertained.

Sep 14, 2011

By Willam R. Normark

During a series of dives with the submersible ALVIN in 1984, samples of massive sulfide were recovered from four vent sites. All sites occur within a linear, steep-walled cleft about 50 m wide and as much as 30 m deep. The cleft bisects the axial valley floor throughout the 15-km-long study area and appears to have been the source for the most recent volcanic eruptions in the valley. Three of the vent sites are defined by a set of discrete hydrothermal discharge zones; as many as eight have been identified over a distance of 500-800 m along the cleft floor. Sulfide deposits occur as individual and coalesced mounds, spires, and chimneys generally less than 3 m in height but a few might be as high as 10 m. The vents are also marked by extensive, yellow-to-amber ferruginous sediment and clots of bacterial matter. Some vents have extensive colonies of tube worms, gastropods, mollusks, and several predator species, such as crabs and squid. The fourth vent site has no visible discharge and consists mainly of "dead" spires and chimneys of massive sulfide. The massive sulfide samples collected with ALVIN are primarily sphalerite with minor marcasite, pyrite, pyrrhotite, isocubanite, chalcopyrite, wurtzite, and anhydrite. Bulk analyses of these chimney and spire samples show Zn contents approaching 60% by weight and significant enrichments in Ag and Cu. Vent fluids have the highest concentrations yet reported for Zn, Fe, and Mn. Thus, the Zn- and Ag-rich nature of massive sulfide from the southern Juan de Fuca Ridge study area

Jan 1, 1985

By Randolph A. Koski

Since 1985, numerous constructional sulfide-sulfate deposits in the form of mounds, pinnacles, chimneys, and sheets have been located between 40°45&apos; and 41°05&apos;N latitude in Escanaba Trough, the sediment-covered axial valley of the Southern Gorda Ridge. Single-channel seismic data indicate that three volcanic edifices up to 6 km in width penetrate as much as 500 m of turbidites that fill the valley; pillow and sheet flow lavas are exposed on the sea floor where these volcanoes breach the sediment surface. Observations from deeply towed camera systems and submersibles show that the largest hydrothermal deposits occur along the step-faulted northern flank of the central volcanic edifice and on the peripheries of steep-sided, sediment-capped hills, approximately 1 km wide and 100 m high, that rise above the valley floor. The sulfide deposits are highly oxidized, eroded, and partly buried by unconsolidated sediment; aprons of sulfide talus extend downslope from the mounds. Two types of sulfide have been sampled by dredging and submersible. The predominant mound and chimney material is pyrrhotite-rich massive sulfide with low amounts of Zn, Pb, Cd, and Ag. Coarse-grained zones with high porosity mark the location of myriad fluid channelways. Thin crusts of barite associated with pyrrhotite-rich sulfide have Au contents up to 2 ppm. Zoned fragments of polymetallic (Fe-Zn-Pb-Cu-As-Ag-Sb) sulfide dredged from a single site near 41°01&apos;N latitude are part of a chimneylike vent structure with a

Jan 1, 1988

By S. W. McCandless

Since the mid 1970&apos;s, the science of remote sensing has invented and demonstrated sensors that hold unique promise for users that operate in the marine environment. Earlier, visible and infrared sensors provided images and temperature maps of surface conditions, but the 1970&apos;s introduced active (radars) and passive (radiometers) microwave sensors capable of penetrating clouds and operating day or night over the world&apos;s oceans. Space-based observation satellites permit these systems to span the globe many times each day, providing a view of the world&apos;s oceans and Arctic areas consistent with daily and, sometimes, hourly changes in the marine environment. Experimental satellites launched by NASA proved that such systems had great scientific merit, but, even more importantly, they could produce information valuable to marine transportation, fishing, and resource exploration and extraction. This latter subject includes the off-shore search and production of petroleum and natural gas resources and ocean mining as well. A few early satellites, such as GEOS-3, Nimbus-7, and most notably Seasat established that global wind fields, all weather sea surface temperature, ocean topography and sea state, and fine scale images of wave patterns, surfactants,

Jan 1, 1986

By Glen Smith

Nautilus Minerals is the world leader in exploration and development of deep ocean seafloor massive sulphide (SMS) resources. The company is currently focused on generating its resource pipeline in the Western Pacific and its first development project for recovery of high-grade copper, gold and silver mineralisation from its Solwara 1 site in the Bismarck Sea, Papua New Guinea. The Solwara 1 site is located at a water depth of 1,600 ? 1,800 meters. Over 150 SMS seafloor surface samples have been collected from chimney structures during dives made by remote operated vehicles (ROVs). In order to obtain an understanding of the sub-surface mineralisation, Nautilus carried out 4 drilling programs between 2006 and 2010 which allowed the calculation of a Canadian NI43-101 compliant resource estimate. The initial 2006 campaign was based on conventional offshore surface driven drill equipment. In conjunction with the subsea remote technology industry, Nautilus subsequently developed an ROV operated seafloor drill system with improved drill core recovery and efficiency. This technology was developed further with a 2010 - 2011 drill program to increase the available geological knowledge at Solwara 1 and adjacent prospects. his paper will provide an overview of Nautilus? SMS drilling requirements and recap the evolution of drilling technology and operations undertaken at Solwara 1 from 2006 to 2011. The paper will also discuss the potential of further developments in drilling techniques and equipment to increase or improve drilling depth, efficiency and data quality.

Jan 1, 2011

By Anthony Wakefield

Dredging tends to be either horizontal or vertical. In each case solids have to be disengaged from the deposit, mobilized, acquired and elevated or translated. One means of elevation is the airlift. Elevation and translation of essentially granular material nay be by jet pump or centrifugal pump. Any of the three types may be used on its own. The airlift and jet pump may he combined for vertical transport and the centrifugal and jet pumps for predominantly horizontal. Both suction point and pipework must have a means of deployment from the surface or from a submerged vehicle or merely a diver. An airlift is an energetic system, having a source of energy and a means of storing it. It therefore will be difficult to prevent oscillation -surging. A centrifugal pump has a characteristic that bends over at low flow rate and is therefore intrinsically unsuitable for pumping solids. The result is blockage, operation at high velocity and correspondingly high wear rates or operation at low concentration of solids and correspondingly low efficiency. The jet pump is intrinsically exceptionally stable but has a low hydraulic efficiency. The jet pump-airlift hybrid prevents or reduces surging and increases system efficiency away from the optimum depth for airlift operation. Delivered solids concentration is increased. The jet pump-centrifugal pump hybrid totally prevents pipeline blockages and increases the productivity from a given pipeline size. For a given energy input the average production is typically doubled. For example, the Indian River Delaware bypassing pipeline transmits an overall day-in-day-out average of 500t/h (tonnes) of sand down a 10.86" diameter line.

Jan 1, 1998

By Nobuyuki Okamoto

The 21-year long-term Japan-SOPAC Cooperative Deep-sea Mineral Resources Study Programme was completed in March 2006. The Programme, which commenced in 1985, has seen numerous marine research surveys being conducted within the Exclusive Economic Zones (EEZs) of 12 SOPAC member countries (Figure 1). The various research and government institutions that have been closely involved in this longstanding Programme include: the Japan International Cooperation Agency (JICA); Japan Oil, Gas and Metals National Corporation (JOGMEC) (formerly, the Metal Mining Agency of Japan, MMAJ) and relevant ministries of the participating Pacific Island governments.

Sep 24, 2006

By M. F. Dibble

The technology available for mining of underwater mineral resources such as placers and phosphorite, typically occurring with variable amounts of overburden, has remained largely unchanged for decades. The traditional bucket ladder dredge with maximum digging depth of 48 m and monthly capacities about 500,000 m3 still reins as the only heavy duty mining system capable of working the tough materials characteristic of heavy metal placers. Attempts at adapting the bucket wheel cutter-suction dredge to these severe conditions have not yet been successful except in moving small volumes from shallow depths. High capital cost (20-30 million U.S. dollars), high cost of overburden removable, and turbidity generation for the bucket ladder are often significant negative factors in mining operations where this system remains the only viable alternative. The Japanese continue to advance the technology of their submersible dredge pump system powered by specially adapted, direct drive electric motors. Present systems are designed primarily for working surficial deposits of aggregate to depths as great as 90 meters, the pump suspended by cable from a surface vessel with an eductor pipe leading from the pump to the vessel. Such a system may prove adaptable to a variety of surficial deposits including phosphorite, shell and heavy minerals in addition to aggregate. However promising for the exploitation of surficial deposits, little advantage can be expected for the deeper buried and more difficult deposits.

Jan 1, 1986

By G. McMurray

The release by the U.S. Department of the Interior (DOI) of a Draft Environmental Impact Statement (DEIS) for the leasing of polymetallic sulfide minerals on the Gorda Ridge in December 1983 resulted in strong negative public reactions. The fundamental issues affecting federal-state relations included the amount of state involvement in the planning process and the continuing question of consistency (sensu Coastal Zone Management Act). The specific issues raised included the authority of DOI to lease nonenergy minerals offshore, the economic and strategic rationale for the proposed lease, and the adequacy of the DEIS. The questions of DEIS adequacy arose in three major areas: the lack of evidence for the existence of polymetallic sulfides on the Gorda Ridge, the lack of sufficient baseline data, and the lack of a mining scenario from which to assess potential impacts. The joint Federal-State Technical Task Force was formed in February, 1984 as part of an initial agreement between the State of Oregon and the Department of the Interior to work cooperatively. Other points in the agreement were (1) a reduction of any future proposed lease area from 40 million acres to no more than 4 million acres; (2) indefinite postponement of the lease sale; (3) deletion of the nearshore portion of the possible lease area covering the physical continental shelf and slope; (4) a commitment of a "tiered" EIS process; and (5) sharing of non-proprietary data with the public.

Jan 1, 1985

By Timothy F. McConachy

Hydrothermal fluids emanating from the seafloor rise as buoyant plumes, entraining ambient bottom sea water on the way up, until they reach density equilibrium and spread laterally in a direction that is governed by near-bottom currents. Plumes provide targets for focussing exploration for seafloor polymetallic sulfide deposits associated with active hydrothermal vents because their lateral and vertical extent is commonly orders of magnitude larger than the vent field from which they originate. Black smokers can inject on the order of 10,000 µg of particles per liter into a sea water column that normally contains only about 10 µg of particles per liter. The resulting plume should be characterized by increased particulate concentration with respect to background sea water and, therefore, provide a measurable gradient towards the source of venting. By utilizing the ability of particles to scatter light, we employed a real¬time, acoustically telemetered, nephelometer to measure this gradient, and mapped the size, shape and particle concentration of plumes at an active spreading center on the Southern Explorer Ridge at lat 49°45.6&apos;N and long 130°16.2&apos;W. Isopach and particle concentration data indicate the presence of two separate but overlapping plumes. The first is associated with a known vent field called Magic Mountain; the second with a new field called AGOR 171, 1.2

Jan 1, 1986

By Tony van der Steen

Subsea mining system are designed for the following, principally different, tasks: Dreding - The destruction and removal of seabed sediments overlaying the bedrock. Cleaning - The competence of the system to systematically remove the deposits from an undulating hard bedrock with irregular pulleys, channels and fissures. Factors that influence the choice of dredging equipment for a specific project are project requirements such as environmental conditions, location and water depth. However, the most important selection criteria are soil conditions. As a consequence, possible dredging systems, must be evaluated for the following, principally different, characteristics: Dredging proficiency - The destruction of the strata by the equipment. System stability - The capability of the soil to support the subsea equipment The above parameters are determined by the strength characteristics and the bearing capacitv_ of the soil. The author describes the processes involved in excavating the subsea deposits and (transporting the gathered soil as a water-soil mixture to the surface using different excavation and transport methods.

Jan 1, 1998

By Michael J. Cruickshank

The State of Hawaii has expressed concern over deterioration of the tourist beaches at Waikiki, which are becoming seriously depleted of sand. In this report the options for acquisition, transportation and placement .of sand on the beach are examined with respect to feasibility and cost. Ten sources of sand were compared, including commercial, from Australia, Maui, and Barbers Point (3), deposits offshore of the Reef Runway (3), offshore of Waikiki (3), and offshore of Molokai from the Penguin Bank (1).

Jan 1, 1991