Search Documents

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By John C. Niedzielski

The PHX Sky Train is a five mile long automated people mover system located at Phoenix Sky Harbor International Airport. Phase I of the PHX Sky Train includes the design and construction of 227 drilled shafts supporting three stations and approximately 9,000 feet of elevated guideway. The guideway includes a 100 foot high, 330 foot long span extending over an active taxiway, which will be the first system of this kind over an active taxiway in the world. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the guideway above the ground surface, where it needs to pass over existing concourse walkways, bridges, a taxiway and buildings. Drilled shaft design involves designing 4.5-foot to 9-foot diameter drilled shafts within the SGC deposits, most of which extend well below the groundwater table. There is a high potential for collapse of drilled shaft excavation sidewalls within this material. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the guideway and stations. A load test shaft was designed and constructed as a means to provide site-specific measurement of axial performance under these difficult conditions. Results from the load test were used to reduce the size of the drilled shafts. This paper provides an overall description of the PHX Sky Train project, a summary of the ground conditions, design requirements, load test results and construction methods and equipment used to successfully install the drilled shafts for this project.

Jan 1, 2010

By Andrew Z. Boeckelmann, David S. Graham, Paul J. Axtell

In the last fifteen years, several research studies have evaluated the ability to detect various types of deep foundation concrete integrity flaws with crosshole sonic logging (CSL) and thermal integrity profiling (TIP). This paper synthesizes the findings from the research, focusing on two studies that included CSL and TIP testing of drilled shafts with various types of flaws. The first, a 2016 research study of test shafts for the Wisconsin DOT, included inclusions inside and outside the reinforcing cage, intentional tremie withdrawal during concreting, and soft bottom flaws. The second, a 2021 study of production shafts for the Missouri DOT, included one shaft with and another without soft bottom conditions. After synthesizing the ability of each test method to detect each type of flaw, the paper presents recommendations for improving how CSL and TIP results are evaluated in practice. The recommendations highlight DFI‟s CSL interpretation protocol as well as the importance of evaluating TIP data versus time, not just depth. The paper includes example temperature-versus-time plots for various types of flaws and emphasizes how temperature-versus-time evaluation can be used to distinguish soft bottom conditions from standard bottom-of-shaft temperature roll off.

Oct 1, 2022

By Waddah Akili

At an offshore site along the Red Sea coast of Saudi Arabia, marine structures were supported on tubular steel piles driven into coral and coral contaminated sands and silts. Surprises and disappointments faced during the installation of the piled foundation were, to a large measure, due to inappropriate design methodology and absence of proper soil information. The paper describes the design evolution process, highlights the static pile test program conducted to verify design parameters, and amplifies the need to prepare for worst possible scenario when coral deposits are encountered. Despite corrections made to the design, based on site-specific insitu parameters (skin friction, end bearing) perceived from load tests conducted on site; the final design adopted overestimated capacities in over 50 percent of total piles driven. The paper describes the changes introduced to the design during the execution of the project, highlights the pile test program conducted to verify the design, and compares pile design penetration with actual penetration depth. The unpredictable and erratic pile behavior observed, ascertains the need for more appropriate pile design and installation guidelines for driven piles in coral and coral contaminated formations.

By Slav Tchepak

The King's Wharf development is located in Sydney's Darling Harbour area. The site was originally used for industrial maritime purposes, which over the years has been reduced to accommodating leisure craft only. The site has been filled with various materials, resulting in fill materials varying from soils, to concrete and rock fill. A prestigious new residential development at the site required piles to found in Sydney sandstone that occurred at depths ranging from 1 to 27m. The selection of appropriate pile types is discussed, as are details relating to the design and construction of cast insitu Omega piles and CFA piles. A number of issues needed to be addressed relating to the piling, including the design of the piles, the potential for liquefaction of the fill material due to earthquakes, penetration of the piles through the fill materials, installation of the piles to a satisfactory positional tolerance and pile performance. A number of piles were dynamically tested to prove pile performance and these results are presented and compared with design expectations. The project was successfully completed on time and budget, indicating the selection of pile types in the difficult ground conditions to be appropriate.

Jan 1, 2000

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which -are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-In-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

May 11, 2007

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By Daniel Stevenson, Richard Guenther

"The preservation of historic buildings is not only essential to the understanding of our national heritage, but it is also environmentally responsible to adapt existing buildings to compatible new uses. With this perspective, the American Enterprise Institute began exploring options to expand the newly acquired Andrew Mellon Building, located at 1785 Massachusetts Ave. NW in Washington, D.C., without causing any harm to the Beaux Arts style limestone façade and its plaster interiors. The building is a National Historical Landmark, but its 72,000 sq ft (6,690 sq m) of usable floor space did not meet the needs of its new owner. The building perimeter is very near the property line, so horizontal expansion was not possible. Adding height to the building was not an option, as this would have altered the historic nature of the building exterior. The only feasible option that could provide the desired floor space was to add a new floor underneath the existing structure. By adding a level beneath the existing building, an additional 28,000 sq ft (2,601 sq m) of floor space could be produced.Berkel & Company Contractors was chosen as the deep foundation/shoring contractor tasked with ensuring that the existing structure was stable and remained undamaged during the excavation and construction of the new lower level. To accomplish this, Berkel provided a shoring system that would act as both excavation support and permanent deep foundation elements for the final structure.Preservation of the existing limestone façade and plaster interiors was critical to the success of the project, as additional foundation settlements could damage these irreplaceable building components. Project specifications, therefore, included very stringent limits for foundation settlements. The maximum allowable total settlement for all existing building walls and columns was ¼ in (6 mm) for the duration of the project."

Jan 1, 2017

By Jonathan J. Dewsbury

It is argued that approximate computer based methods are only suited to modelling conventional piled rafts, for pile enhanced rafts where the interactions will be non linear three dimensional finite element analysis is required. However current 3D finite element analysis often relies on symmetry to reduce computational cost and there are concerns over the dependency of the results on the user. Therefore a new strategy within the finite element framework has been proposed. The main advantage of this strategy is that each stage of the model can be checked for consistency. There is also the added benefit that non symmetrical models can easily be constructed by tying the validated components together without dramatic increases in computational time. The proposed strategy compared well to the published results of a hypothetical example of a piled raft previously analysed with numerous methods by Poulos et al. (1997).

Jan 1, 2010

By Bartho J. Admiraal, Antoine Feddema

Pneumatic sinking of caissons has been established from mid-19th century. The technique of pneumatic sinking has been applied on many projects for underground construction up to depths over 20m below groundwater level since that time. Volker Staal en Funderingen, a known deep foundation contractor in the Netherlands, was awarded two contracts in 2015 for sinking in total 2 caissons in Hamburg (Germany) to large depths (over 30 m (100 ft) and two projects near Amsterdam (the Netherlands). The latter concerned two gate chambers for the world’s largest sea-lock, one of them was 55x81 m2 (180x266 ft) to a depth of 25.5 m (84 ft), which would mean a world record for pneumatic sinking! But with depths and dimensions like these, the deployment of personnel is the main limiting factor for production, despite all developments to date. It was decided to develop a remote controlled process, including the necessary equipment and monitoring systems. Monitoring not only the kinematics of the equipment in the working chamber and the production parameters related to the excavation but also of the structural behaviour of the sea-lock gate chambers was essential for approval of this innovative execution method. The lay-out and the sizes of the largest caisson the structural integrity was extremely critical for torsion and bending moments. A displacement controlled execution by the observational method was therefore required. In engineering a new approach for modelling the semi-continuous failure mechanisms of the soil was needed to understand the sensitivity of the excavation process and to define limit values for the execution. In the paper these structural and geotechnical issues will be explained together with the experiences during the execution.

May 1, 2022

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By Ryan Sullivan, Lisa Smiley, Jewels Stover

The Westerly Storage Tunnel (WST) Project is part of Project Clean lake, the North East Ohio Regional Sewer Dist years. When completed in 2020, WST will be nearly 2 miles of 25-ft diameter tunnel 200-250 ft below ground. The storage tunnel will manage higher flow volumes, keeping stormwater out of the combined sewer system reducing overflow occurrences. Three deep shafts provide access to the tunnel at the tunnel boring machine (TBM) launch and retrieval sites, as well as a vent shaft. Support of excavation for the access shafts was constructed utilizing unreinforced concrete diaphragm walls. This innovative, value-engineered alternate design significantly reduced risks associated with conventional secant piles combined with a rib and liner plate system. Implementation of the diaphragm wall technology resulted in a water tight, continuous shaft keyed into rock. This case study examines the design, methodology, and installation challenges unique to each shaft, as well as the benefits of the final product to the overall project.

By Julie Clarke

In 1939 Dr. Ralph Peck criticized the Civil Engineering community for taking a bifurcated approach to the prediction of building damage due to subsurface geo-technical works. Specifically, he observed that Geotechnical Engineers concerned themselves only with subsurface issues implying that their results were largely independent of the presence and condition of the structures above. He continued that Structural Engineers charged with risk assessment of buildings approached their work nearly in isolation of below ground activities. Seventy years later, although the state-of-the-art has enabled a better understanding of soil-structure interaction, the reality remains that risk assessment from subsurface construction, is not yet an integrated activity when done on a large-scale basis. To help move beyond this, this paper proposes a new, integrated methodology for preliminary assessment that considers a three-stage process that involves the following: (1) traditional empirical relationships for predicting ground movement from tunneling, (2) recent advances in condition assessments, and (3) architectural designators related to usage and historic preservation listings. The methodology is applied to a study area of nearly 260 buildings in the city center of Dublin Ireland, in an area slated for an upcoming metro. The results are com-pared to the Environmental Impact Statement issued for the official project. Al-though the test case is for tunneling, the approach may be adapted to other subsurface construction activities including excavation and piling.

Jan 1, 2009

By Sudhir Kumar Das

"The exorbitant price of the land in the metropolis has restricted the horizontal expansion and compelled the owners, the developers and the engineers to opt for vertical expansion. This has resulted in the construction of high rises by extending floors of the existing buildings and developing the new ones for which deep excavation is a must. The multistoried buildings up to a certain height can be founded on shallow depth if the soil beneath can withstand the load. If not, the soil can be stabilized by the latest improvement technology to change the properties of soil to cater the desired load of the superstructures. By such practice the cost and time of completion of the substructures can be reduced in comparison to the substructures needed for deep excavation.The necessity of deep excavation cannot be ignored to create housings, underground parking lots and the other public amenities for the urban migrants in the metropolis.Although most of the metropolis have underground mapping the developers, before starting excavation should be hundred percent sure about the alignment and depth of the utilities so that the excavators do not snap the same to bring cut in water supply, power lines, telephone lines etc, resulting in hue and cry in the neighborhoods of the metropolis due to no availability of the essential services The building/structures coming on the influence zones of the deep excavation should be monitored in all sequences of excavations. In case of building underground corridors for rail or road through open deep excavation under a traffic road the developers, before commencing excavation should shift/divert the dry and wet utilities coming on the way of excavation to suitable locations. The surface traffic need to be diverted either temporarily to an adjacent alternative road or allowed to pass over a decking built over the trench of excavation for the affected length of construction. The soil support system is necessary longitudinally on the two sides covering the width of trench for building corridors. In case of building substructures of flyovers built at different plots along the alignment of the flyover or a multistoried complex built at an isolated plot, the soil support system would be necessary on all the sides covering the plot of construction.The material of construction of soil support depends on the depth, type of soil and the type of permanent structure to be developed. Probable geo-hazards inviting casualties in the deep excavation projects occur due to caving of soil, leakage of wet utilities, seepage through honey comb concrete surfaces, failure of pump used for dewatering etc. A detailed comprehensive planning, management and determination of the project authority is essential for marginalizing the casualties. These prevent unforeseen expenditure in mitigation and help to control the time and the cost over run of overall project. The engineer at site should be more a professional manager than an engineer at site. He should be conversant with the safety and environment rules and regulations applicable to deep underground projects."

Jan 1, 2015

By Joel Moskowitz, Jan Cermak

"New York City has unique geologic conditions which must be considered when designing pile foundations. Where shallow foundations are not feasible, the City's subsurface conditions require a variety of deep foundation systems, ranging from high capacity rock socketed piles, to piles end-bearing on bedrock, to friction piles bearing in alluvial or glacial deposits. Pile load testing is essential in confirming pile capacities as pile analyses include assumptions on soil and soil-pile response, and pile driving equipment. Load test results must be interpreted to estimate the long-term pile behavior. Except for lightly loaded driven piles, the New York City Building Code (the Code) requires that pile capacities be confirmed by static load testing. The Code provides the number of static load tests required, test procedures, and acceptance criteria. In the last few decades, methods other than static load testing have been developed including dynamic and rapid (pseudo-static) load tests. Recently, those methods have also been employed on several projects in New York City. The traditional approach to pile load testing in New York City is discussed herein including engineering involved in the analyses of test data with examples. In addition, several projects which included non-static load testing are discussed INTRODUCTIONPile load testing complements the subsurface information and pile design by providing further data on pile-soil interaction for the selected pile type and installation method. Traditional approaches to pile load testing in New York City involve static load tests to verify the design capacity of the piles for a given minimum factor of safety.In the late 1950's, Dr. Phillip C. Rutledge summarized his views on the philosophy of pile foundations in an unpublished, in-house document. He viewed pile foundations as good illustrations of pertinent and impertinent aspects of geotechnical engineering. In the analyses of piles he divided engineering into four general types:(a) Theoretical engineering in which decisions are made based on theoretical analyses. This represents ideal engineering, in which all factors affecting the pile design are well established or, at least, few simplifying assumptions with known effects on the analyses are made."

Jan 1, 2005

By Matthias Pulsfort, Jiarui Du, Torsten Wichtmann, Achim v. Blumenthal, Diethard König, Rowena Verst

The influence of the interaction between support fluid and soil, e.g., filter cake formation, on the shear stress transfer in the soil-concrete interface of diaphragm walls and bored piles is still controversially discussed. Actual research on the soil-concrete interface using bentonite suspensions indicates that shear stress transfer is underestimated by existing standards. Investigations on the soil-concrete interface using polymer solutions are rare. Therefore, complementary field investigations and systematic laboratory studies were conducted to analyse the soil-concrete interface using both bentonite suspensions and polymer solutions. Thickness and composition of real-scale filter cakes were investigated on several slurry wall construction sites, where bentonite suspensions were used. Direct shear tests (60 mm x 60 mm) were executed for soilbentonite mixtures with varying amounts of bentonite and different granular fines representing a realistic bandwidth of in-situ filter cake compositions. Larger direct shear tests (300 mm x 300 mm) with preceding horizontal penetration, subsequent vertical tremie concrete placement, and filter cake consolidation were performed using both bentonite suspensions and polymer solutions. The results support the view that shear stress transfer in the soil-concrete interface can be described by a wall friction angle in a range of 25° to 30° for bentonite suspensions and between 35° and 40° for polymer solutions in non-cohesive soils.

May 1, 2022

By Lee S. Vanzler

Atlantic Wharf involved the construction of a six-level underground parking garage and a 32-story high rise tower along the historic Boston Harbor waterfront. The site, historically known as ?Russia Wharf,? consisted of filled land initially created in the late 1800s by extending the shoreline toward the harbor as the urban population and land needs grew to support expansion of commerce and trade. Redevelopment required solutions to address relics of waterfront structures (granite block seawalls, piles, and piers), weak subsurface soil conditions, tidal groundwater levels, and contaminated soils resulting from previous site usage and filling. The foundation system, consisting of drilled shafts with column loads up to 14,000 kips (62,272 kN), concrete diaphragm wall (slurry wall), and up-down construction methodology, was chosen to address these factors. As a prerequisite for development, selected portions of the façades of the former historic buildings were required to be preserved, protected, and incorporated into the final building configuration. The historic façades were temporarily braced and supported prior to the demolition of the buildings and commencement of below-grade construction. This paper will describe the considerations in the selection of up-down construction methodology along with a discussion of the design and performance of the concrete diaphragm wall and drilled shaft foundations. Up-down construction methodology shortened the overall construction schedule while addressing the lateral bracing requirements for the concrete diaphragm wall and restrictive ground movement tolerances to protect adjacent structures. Below-grade construction was completed in March 2010, and the building was opened for tenant occupancy in January 2011.

Jan 1, 2011

By Moritz Schleeh, Christian Moormann

Temporary working platforms are generally required in order to ensure that heavy construction machinery such as drilling and trench wall units, pile drivers, vehicle and crawler cranes can be set up safely at the site of operation. Considering all possible operating and loading conditions, especially on ground of low shear strength and stiffness, the design and construction of temporary mobile working platforms needs to be considered more as a serious engineering task than as a second order structure of minor relevance. Working platforms reinforced with one or several geosynthetic layers have proven to be especially effective with regard to stability, serviceability and durability but their design requests even more sophisticated approaches. Existing design models are often based on simplified assumptions and do not consider the complex interaction between construction machinery, working platform and subgrade. Non-monotonic loading as well as elastoplastic and time-variant deformation of cohesive subsoil can adversely affect the base layer system and the serviceability and stability of the construction machinery operating on it. In this context, there is a need for improvement of design approaches and their optimisation considering that there are no generally accepted design approaches or technical codes of practice available for the design of temporary working platforms. The present paper deals with the multifaceted and non-trivial interaction effects of working platforms investigated by model tests, field measurements and numerical simulations to develop a design approach that ensures a safe installation and operation of heavy plants on unstable ground.

May 1, 2022