Search Documents

By John Y. L Chen

This paper presents full-scale instrumented pile static compressive and tensile load tests to be conducted in the area of Pearl Harbor, Hawaii. Thousands of piles have been installed to support the existing piers and wharves in the Pearl Harbor area. Due to the absence of bedrock within practical depths, most of the piles use combined friction and end bearing. A new 925 feet (282 meters) long and 50 feet (12 meters) wide reinforced concrete wharf supported on pile foundation is planned. This paper will present results of soil investigation, laboratory testing, dynamic load tests during indictor pile driving and static pile load tests. The subsurface conditions consist of soft harbor sediment, young alluvium deposit, volcanic tuff rock formation and stiff old alluvium deposit. The load test piles consist of 20-inch (508 mm) square and 24-inch (610 mm) octagonal pre-stressed, pre-cast concrete pile and instrumented with embedded strain gauges. The length of the piles ranges from about 50 to 125 feet (15 to 38 meters). The test pile program consists of probing, driving indictor piles, dynamic load tests during indictor pile driving and static load tests. The standard loading procedure method was used during static pile load tests.

Jan 1, 2002

By Edward Jacobsen

The Oak Creek Power Plant in Oak Creek, Wisconsin is currently undertaking an expansion project. In order to supply cooling water to this facility, a 27' (8.2m) diameter tunnel will be bored, in rock; to connect to 4 vertical Intake shafts located approximately 1.5 miles (2.4km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to Install these intake shafts. When complete, the plant is expected to circulate upward of 2 billion gallons per day (7.5 billion liters) through this system. Two shafts were drilled in a (shortened) construction season in 2005 and the remaining 2 shafts and 4 liner assemblies were completed in 2006. Future connection to the tunnel, in 2007, will be accomplished by mining upward to reach the lower portion of each liner and then removing its internal bulkheads to permit the flow of the lake water into the tunnel.

May 11, 2007

"The development of non-destructive testing (NDT) methods for deep foundations occurred in several parts of the world, gradually coming together into the present state of the art. The compilation of this brief NDT history is the best effort of several knowledgeable members of the Deep Foundations Institute (DFI) Drilled Shaft Committee, coupled with the recollections of several historically important contributors to the science. It is not intended to be exhaustive, but rather concentrates on the origins of the methods in common use and on which this manual focuses.Modern NDT methods, and the spread of knowledge about them, have expanded through application to real foundations projects by the original researchers, sometimes inspired by their own curiosity, sometimes to respond to the cost and time limitations imposed by static testing, and sometimes to address the questions raised on research projects funded by large government agencies such as the Federal Highway Administration (FHWA) in the USA, and various European transportation agencies. Initial attempts were primitive by today’s standards, and equipment limitations often restricted successful application to relatively simple cases. As electronics improved and confidence in them increased, the early researchers began commercial promotion of their methods, published their findings in professional journals, and shared experiences at conferences held by such groups as the DFI, the International Association of Foundation Drilling (ADSC), the International Conferences on the Application of Stress-Wave Theory to Piles and other venues such as ASCE and Transportation Research Board (TRB) conferences.NDT methods were developed to fill a need to assess the quality assurance of deep foundation elements. New pile types and higher design loads prompted engineers to verify the safety of their foundations via additional testing during construction. Static load testing was the traditional method to assess performance, and this method has been used for centuries and perhaps even millennia.Relatively recent alternatives to static load testing for determining the capacity of drilled shafts include the bottom load test method. This method uses a jack embedded in the lower portion of the pile (bottom load test) and was first reported to be used from Canada in the early 1970’s (Gibson& Devenny 1973). The concept immediately caught on in Israel, where it was used as a quality control measure for small-diameter piles drilled in rock (then a new technology). The method was later patented in the US by Jorj Osterberg, and offered as a commercially available service in thelate 1980s (Osterberg, 1989)"

Jan 1, 2004

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By Manasi Wijerathna, D. S. Liyanapathirana

"Deep cement mixing is a popular soft ground improving technology that improves the bearing capacity and settlement characteristics of natural soil. When Deep Cement Mixed (DCM) columns are installed attached to each other in a wall configuration, the walls are capable of resisting bending moments and shear forces in the direction transverse to the columns. Therefore, installing DCM walls beneath the embankment slope perpendicular to the alignment of the embankment is a proper solution to prevent excessive lateral deformations of the embankment. Previous research studies have shown that failure patterns of DCM column walls are different to failure patterns of individual DCM column rows, under lateral loads. This study investigates the failure patterns of embankments where DCM column walls are located beneath the slopes, with respect to DCM wall strength, DCM column wall width and the spacing between DCM walls. 2D and 3D numerical models developed using the ABAQUS/standard finite element programme, were used in this investigation. Results show that the DCM wall strength and width of the DCM wall have a significant influence on the failure mode and the critical failure surface of the embankment. 3D simulation results demonstrate that the failure due to soil extrusion between columns was less pronounced in embankments improved with DCM walls, due to the interaction between the DCM walls and the surrounding natural soil.INTRODUCTIONEmbankments constructed over soft ground are highly susceptible to global slope failure and excessive displacements due to combined effects of vertical and lateral loads beneath the embankment slope (Zheng et al., 2009, Han and Gabr, 2002). The overall stability of the embankment can be significantly improved by improving the soil beneath the slope of the embankment using Deep Cement Mixed (DCM) column rows or overlapped DCM column walls (Jamsawang et al., 2015, Larsson and Broms, 2000, Topolniki, 2004, Broms, 1999). According to the literature, the improved ground experience different failure modes other than shear failure, such as separation of columns, overturning, shear failure along the columns or dowel action (Broms, 1999). Some of the failure modes reported by Broms (1999) are shown in Fig. 1. The ultimate failure mode depends on the geometry and the strength of the improved ground (Jamsawang et al., 2015, Kitazume and Maruyama, 2006, Kitazume and Maruyama, 2007)."

Jan 1, 1900

By Frank Rausche

Why testing What tests can be done Dynamic load testing Loading device Measurements Analysis Examples

Jan 1, 2001

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By Takefumi Takuma, Ali Fayad, Shigeru Kambe

"This paper discusses the unique design and construction circumstances of the cantilevered dual sheet pile walls and the Accordion Sheet Pile Wall for the repair and upgrade of the East Garden Grove-Wintersburg Channel in Huntington Beach, California that was concluded in 2014. It also describes the 2008 Emergency Sheet Pile Project for the same channel. Both projects utilized the Press-in Piling Method for its low noise and almost no vibration advantages.BackgroundThe East Garden Grove-Wintersburg Channel is part of the Orange County Flood Control District (OCFCD) and is operated and maintained by OC (Orange County) Public Works (see Figure 1 for its location). The channel, referred to as OCFCD facility # C05 (C05), had suffered significant toe undercutting and slope erosion of its levee due to a series of storms. These began after the facility was constructed in the 1960’s and culminated in 2005. Consequently, the levee was deemed significantly deficient and was eventually declared as a local emergency in 2007. C05 was an incised channel and its levee was constructed primarily from native materials. Operation and Maintenance (O&M) personnel notified the design staff at OC Public Works to be aware of major consequences associated with the dilapidation problem in the most downstream reach of the channel in the vicinity of the Bolsa Chica Wetlands Restoration Project. In 2007, the Orange County Board of Supervisors declared a local emergency to fix the levees with sheet piles to be driven by the Press-in Piling Method, hydraulic pushing piles into ground by holding onto previously installed piles. The project that ensued represented the first in-tandem use on the West Coast of the United States of the Press-in pile driver with its GRB System (Press-in pile driver, a support crane and pile transporter travel on top of already-driven sheet piles). This is further discussed in this paper in the sections titled “Press-in Piling Method” and “GRB System”, respectively. The project repaired approximately 3,800 feet of erosion on the north levee of C05 with 45-foot long cantilevered sheet piles. The sheet piles design constraints are discussed in this paper in the section titled “C05 2008 Emergency Sheet Pile Project (Phase 1)”. Between 2012 and 2014, another mile’s worth of levee reach was improved with the Soil-Mix-Sandwich (SMS) Method. This concept consisted of deep soil cement mix (DSCM) columns sandwiched within the dual rows of sheet piles. Additional details on the SMS, its DSCM construction, and its hybrid geo-structure design concepts are well beyond the scope of this discussion, which is primarily focused on sheet piles. Instead, the interested reader is referred to two papers on the SMS and its DSCM metrics (Fayad, 2015; and Arora, et al., 2015). These were presented and published in the Proceedings of the Deep Foundations Institute (DFI) 2015 Conference on Deep Mixing. Hence, in the section of this paper titled “C05 SMS Dual Sheet Piles Project (Phase 2)” only the sheet pile design constraints of the SMS are covered. Finally, in the area where the project traversed the Alquist-Priolo zone of the Newport-Inglewood tectonic fault, an expandable and deflectable sheet pile wall was used to isolate the flood channel from the Bolsa Chica wetlands. Its details are addressed in the section titled “C05 Accordion Sheet Pile Wall (Phase 2)” of this paper."

Jan 1, 2017

By Joe Harris

Large structures, such as a multistory office building or a large storage tank, are constructed the most economical way possible, which may involve a shallow foundation system placed on native soil or compacted fill material. Over the life of the structure, the foundation system may not perform as originally anticipated, leading to differential settlement. Minor differ- ential settlement is expected; however, settlement that exceeds allotted tolerance can render the structure inoperable. Compaction grouting is a well-known and accepted ground improvement technique that can be used to not only stabilize but relevel multistory buildings and large dia- meter storage tanks. Two projects, each with differing types of structures, were successfully remediated utilizing com- paction grouting as the primary method to remedy settlement.

Sep 1, 2023

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By Tony D. Canale, Anthony Mazzo

"Times Square, arguably one of the best-known destinations in the world, has undergone and continues to undergo a re-development aimed at attracting corporate tenants to the area. Mueser Rutledge Consulting Engineers (MRCE) was involved with the planning, design and construction of the foundations for the Conde Nast and 5 Times Square sites, as well as Times Square Tower. These sites are pictured in Figure 1.This paper will focus on the design and construction of the deep foundations for Times Square Tower that was developed by Boston Properties. PROJECT DESCRIPTIONTimes Square Tower is 47 stories tall, with no setbacks and an overall height to top of crown of 730 feet (222.5m). It has two basement levels extending 30 feet (9m) below grade over the full site. As shown in Figure 1, the structure occupies the entire site and has a footprint of 22,000 square feet (2,044 m2), with a total rentable area of about 1.2 million square feet (111,480 m2). The planned use for the building is office space with retail at the ground level. When completed, Times Square Tower was the final building constructed as part of the Revitalization of Times Square. Due to the site constraints, designing and constructing the foundations was akin to placing the final piece of a puzzle.Times Square Tower provided numerous design and construction challenges that were a result of tight working conditions, heavy column loads, and a compressed schedule.GEOLOGIC SETTING AND SITE HISTORYThe Times Square area is part of the Manhattan Prong called the Manhattan Ridge, a formation of old and durable metamorphosed and folded bedrock, now termed the Hartland Formation. The bedrock generally has a thin soil cover and uneven surface overlain in some areas with a thin mantle of decomposed and/or weathered rock. Overburden soils include glacial and post-glacial deposits and recent fills.Transit improvements have been made in and around the Times Square area since the early 1900’s. The 1, 2 and 3 Subway Lines that run below 7th Avenue were constructed circa 1915 using cut and cover techniques and extend about 28 feet (8.5m) below grade. The N, R, Q & W Subway Lines that run below Broadway were also constructed in 1915 using cut and cover techniques and extend about 38 feet (11.6m) below grade. The 7 Line that runs below 41st Street was constructed later, using both cut-and-cover and tunneling methods as it runs below the other subway structures at a depth of about 55 feet (16.8m) below grade."

Jan 1, 2005

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By John C. Niedzielski

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site?s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The full-scale field test played a significant role in the design of the project?s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

By Antonio Zechini, Giuseppe Iorio, Massimo Grisolia

"The new C Line of the Rome Metro runs northwest to southeast across the city center, with 30 new stations and a total length of more than 15.5 mi (25 km). Due to the presence of a dense urban environment, the selected solution for the construction of the stations consists of a cutand- cover excavation, which is retained by multipropped diaphragm walls to minimize settlement and prevent damage to the nearby structures. The bottom of the excavation of the underground stations are about 82 ft to 98 ft (25 m to 30 m) below ground surface, and about 66 ft to 82 ft (20 m to 25 m) below the groundwater table. To ensure dry conditions and to prevent hydraulic base heave instability, deep well systems were designed and used to lower groundwater level and piezometric head during excavation. The dewatering field tests showed how the local stratigraphy strongly affects the dewatering efficiency. Finite element modeling (FEM) of steady state filtration were used to compare the soil permeability with Lefranc in-situ test results and to verify the efficiency of the grouted plugs. The geological sequence along the new C Line consists of a very heterogeneously layered deposit. The base deposit of stiff overconsolidated clay (“APL,” Pliocene age) is overlain by fluvio-palustrine very dense sandy gravels (“SG,” Pleistocene age), which are then overlain by medium stiff clayey silts or dense sandy silts (“AR” or “ST,” Paleotevere units). These deposits are overlain by covered by pyroclastic volcanic soils, tuff, silty sand and sandy silt (Middle to Upper Pleistocene) deriving from the Colli Albani apparatus. A layer of made ground (“R”) of varying thickness covers the stratigraphic sequence and the natural soil profile everywhere.The local hydrogeological framework is very complex and characterized by a double groundwater system. The upper main aquifer is mainly represented by the “pozzolane sequences” (“PR/PN”), while the lower aquifer consists of a deposit of sandy gravel (“SG,” Pleistocene), which is underlain by marine claystone bedrock (“APL,” Pliocene). The pyroclastic deposits (e.g., pozzolane, lithoid and pseudolithoid tuff and clayely tuff) show large variations in permeability due to porosity, compaction processes, sealing and secondary fracturing. Permeability values for each soil type were determined using Lefranc tests at variable head and using pumping tests. The Lefranc tests indicated a wide range of permeability."

Jan 1, 2017

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2013

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015