Search Documents

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By Alexander Filotti, Richard Kalson

"1. INTRODUCTION- WHAT IS P3 OR PPP ?The Public Private Partnership (PPP or 3P) is a project delivery scheme based on the government providing land and/or a concession agreement, and on a private entity providing the design, construction, financing, operation and maintenance of the project for an extensive duration of time (up to thirty years). At the end of the operation-maintenance period, the project is turned over to the public entity, which fully owns the project at all times. While there are many PPP delivery schemes used around the world, for the present paper, we are going to analyze the impact of the Design-Build-Finance-Operate-Maintain (DBFOM) scheme on the deep foundation specialty subcontractor. There are couple of reasons that the PPP delivery system started to be used and implemented not only by developed nations (e.g. United Kingdom, USA etc.), but also by the International Development Bank for delivering major infrastructure projects in developing nations. From the point of view of government agencies, some of the reasons to use PPP are the following:??The primary use of private capital in an era where borrowing and/or supplemental taxation represents too much of a political risk. Budget deficits and taxation limits are extremely hot topics in every election (national or local) and the level of education of the electorate in this area is making it more and more difficult for politicians to use borrowed funds and additional taxation finance sources for public projects. At the same time, we see an increase in the social expenditures of the government in parallel with a needed increase in expenditures on infrastructure due to aging and neglect.??Bundling the construction risks with the operational and maintenance risks naturally pushes the private entity to increase the level of innovation and communications in the primary phase ( the construction phase) in order to develop future process based upon the innovation and communications utilized in the operation and maintenance phase of the project. This is true if contractual incentives are properly structured because “all revolves around incentives. In a world of ‘incomplete’ contracts, where it is difficult to foresee and contract about uncertain future events, it is important to get the incentive structure right” (Grimsey and Lewis, 2004).??The transfer of very expensive risks such as differing site conditions, schedule, design, construction, maintenance and operation costs from the public authority to the private entity.??The timespan of development and construction of a PPP project is usually shorter than the traditional procurement process (e.g. “ the I-595 P3 provided capacity improvements fifteen years sooner than a conventional plan would have offered. In Maryland, an innovative expansion of the Seagirt Marine Terminal in the Port of Baltimore was completed two years ahead of schedule due to the P3 model. As a result, the Port of Baltimore is only the second port on the US East Coast to have unrestricted access to both a fully functioning 50-foot channel and 50-foot berth.”)"

Jan 1, 2017

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

By Dileej M. Dewaikar, Poonam A. Patil

"In this paper, the ultimate lateral resistance of a long, flexible, unrestrained vertical pile in a cohesive soil is computed under static loading condition using py curves. A simple and improved method for the construction of hyperbolic p-y curves for a cohesive soil is proposed for static loading conditions. An iterative analysis is employed with secant modulus approach, using a matrix method known as moment area method developed by Sawant and Dewaikar. The loadground line displacement relationship is obtained for different load eccentricities using p-y curves developed by Matlock, Georgiadis et al. and the proposed hyperbolic p-y curves for different eccentricity ratios. These values are compared with the values computed from model test performed by Rao et al. and with the limit equilibrium solution given by Broms. The comparison shows that, the results obtained using hyperbolic p-y curves shows a better agreement with the model test data with the maximum difference within 15% using other methods; whereas Broms' limit equilibrium solution shows some agreement with the results based on Matlock's p-y curves.INTRODUCTIONPile foundations are used for jacket type offshore structures, which are subjected to large magnitudes of lateral loads due to lake or ocean waves, winds and ice forces. The failure of a pile-soil system is catastrophic and excessive deflection of the pile creates operational difficulties. In the view of this, bending moment in the pile is required to be predicted in a rationar manner. The p-y concept developed by Reese and Matlock (1956) is popularly being used to estimate the pile top deflection and bending moments.The ultimate lateral load which causes collapse of a pile-soil system is generally estimated using Broms' (1964) method, which is based on limit equilibrium considerations. The p-y curves are basically nonlinear in nature and include ultimate pressure at the depth where they are generated. Therefore, if the lateral deflection of pile top against different magnitudes of lateral load is obtained, it should be possible to obtain the ultimate lateral load from this load-deflection relationship."

Jan 1, 2005

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Amanda R. Parry, Chris R. Pray

Predicting and modeling the soil structure interaction of laterally loaded piles with significant unbraced lengths is one of the challenges faced in designing many waterfront structures. Designers often rely on pile specific design software to calculate forces in an embedded pile and then couple that with either a structural design software to capture the behavior of the rest of the structure or use potentially overly conservative assumptions to omit modelling the piles entirely. Given that some projects have hundreds of piles coupled with hundreds of loading conditions, the shuttling of results from the structural analysis software into the pile analysis software can become cumbersome, difficult to track and manage, and prone to user input errors. An alternative approach recently used on two large marine infrastructure projects consisted of calibrating a structural analysis software to replicate the resultant outputs from a software developed specifically for pile analysis. This calibration was done using thoughtfully placed springs along a pile modeled in the structural analysis software to replicate the soil-structure interaction of the piles. The focus of this paper will be on the methodology used to calibrate the two software programs and an evaluation of the results which showed close agreement. Based on the two case studies, calibrating a generic finite element analysis software via this method should be considered as a reasonable and time saving design approach for pile-supported structures.

Sep 8, 2021

By Dzianis Proshchanka, Yoshi Izumi, Koji Mitani, Ayuna Kitaura

"A new pile driving and drilling navigation system has been developed. It utilizes the commonly used surveying total station, combined with an innovative reticle. Conventional crosshairs have been replaced by a concentrically circular reticle called Baum. It allows for easily performed measurements of central axes of cylindrical objects such as piles, chimneys, electricity poles, etc. This provides several significant advantages compared to other existing systems. It is cost-effective as only one operator is required to control deviations in positioning and inclination. Furthermore, repetitive reinstallation of the instrument is not required for every pile driven or hole drilled. It is also a safer method, as workers have no need to be near a pile driver or drilling machine to perform the measurements. With Baum Station, necessary measurements can be performed away from the actual work area. Moreover, it is highly accurate with real-time solutions, as three-dimensional orientation information for the pile/drill is obtained simultaneously with the pile being driven or the hole being drilled. This allows for the highest levels of precision-control and correction to minimize eccentricity of the intended center positioning.INTRODUCTIONBackgroundIn foundation construction for structures, pile foundations are widely used for deep bearing strata. There are two patterns to driving piles: vertically or obliquely to the ground. The shapes of the piles are normally cylindrical. Vertical pile foundations are employed as the foundations of many structures due to their high workability. There is a problem however, which is that this method does not bear measurement data as construction accuracy is visually checked. On the other hand, tilted pile foundations are rarely employed because it is too difficult to ensure construction accuracy. In addition, commonly used percussion methods create noise and vibrations when the piles are hit, while there are advantages that thinner piles are available, ensuring earthquake-resistance, as tilted piles curb horizontal displacements of structures, which may be caused by earthquake ground motion. However, current requirements of cost reduction bring professional attention to tilted pile foundations, which can be driven reasonably and economically with much research of tilted piles having been carried out to improve their capacity. Also, a method of screwing piling has been developed, which produces small amounts of noise and vibrations. This method has solved tasks of workability and environmental burdens, and is becoming more and more common. However, there is a necessity to develop a method to accurately measure angles of piles’ axes in order to drive piles into the ground with appropriate angles. It is also expected to find out a way to control construction information, such as correction amount and driving record."

Jan 1, 2017

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan PhD

The experience gained during more than 900 Crosshole Sonic Logging (CSL) tests on drilled shafts shows the importance of establishing proper project acceptance and repair protocols. Drilled shaft evaluation is a multidisciplinary task that should not be left solely to the outcome of the CSL test. This test allows to characterize and delimit areas of different qualities of concrete, and it is important that all the interested parties understand the difference between flaws and defects. The information presented here is intended to give a guideline to contractors, inspectors, engineers, owners and clients on how to deal with acceptance and remediation of defective drilled shafts, detected using CSL tests. A database of flaws is presented depending on their location, intensity and remediation method. Procedures that allow the flaws to be analyzed are presented in order to dismiss or classify them as defects. In many cases, the CSL test may indicate an anomaly, but by coring the concrete and analyzing the structural demands and conditions, the flaw can be classified as non-severe. When flaws are classified as defects, their repair will depend on the area where they are located in the drilled shaft pile. In this document two procedures are described for repairing defects depending on their location. For defects in the drilled shaft head area, the procedure takes into account the interaction between the new and old concrete. For repairing the middle zone of the drilled shaft by grouting, the major concerns are the difficulty of accessing through the drilled shaft at deep depths and the communication between boreholes. For defects at the drilled shaft tip, two proposed remediation methods are presented. Finally, tomography tests are presented to compare the effectiveness of remediation by grouting.

Oct 1, 2022