Search Documents

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By Loring A. Wyllie

Preparation, understanding and use of soils reports must be a team effort to be fully effective. The soils engineer must know what is to be built and exactly where. The structural engineer and owner must be fully informed on the foundation problems of the site. There must be frequent team review of information obtained from subsurface investigation and of design as details develop. The soils engineer should be available on a continuing team basis as design proceeds and should be directly involved with inspection and interpretation of site conditions as construction continues.

Jan 1, 1986

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Carole L. B. Mitchell

The increased use of micropiles and soil nailing presents a growing database of verification and sacrificial load test data. In Washington State, the use of micropiles is becoming common, and soil nails are now almost as widely used as tiebacks; yet the state of the practice in understanding load transfer rates has not improved. This research compiles load test data for micropiles and soil nails from Shannon & Wilson?s records in the Puget Sound region of Washington. Ultimate and maximum load transfer rates for design are correlated to geologic units and soil types found in the region. Variables such as pressure versus tremie grouting, hole diameter, soil density/consistency, and the presence of groundwater are compared to load transfer rates for similar geologic units and soil types. Results are also compared to published PTI, AASHTO, and FHWA guidelines. Our results indicate that published ranges may be conservative for some soil types in the Puget Sound region, especially for micropiles. Performing verification tests to failure instead of typical verification or performance tests is needed to improve correlations and provide less conservative design load transfer rates.

Jan 1, 2006

By Z. M. Zhang

Fracture grouting is a particular technique which can be used in soils and rocks with low permeability to increase groutability and penetration rates and to solve some special foundation problems by inducing limited and controlled zones of hydrofracture surrounding the injection source. The present paper describes the basic principles of hydrofracture and its application to grouting in deep foundations, and indicates some recognitions about the mechanisms and effects of fracture grouting.

Jan 1, 2010

By Jogeshwar P. Singh, Ahmed AlaaEldin, Mohamed Ashour

The presented methodology allows the determination of the response of laterally loaded battered long piles in sandy soils based on the soil-pile interaction. The Strain Wedge (SW) model which was originally developed for laterally loaded vertical piles is modified to assess the behavior of laterally loaded battered piles with the consideration of soil and pile properties. The method predicts the pile-head response and associated p-y curves. The presented soil-pile model accounts for the variation of the direction and magnitude of the batter angles from the vertical position. Unlike current practice, the proposed technique also provides the p-y curves for battered piles in sandy soils based on soil and pile properties (i.e., sand relative density, friction angle, pile geometry, etc.). The proposed methodology has been validated through a number of comparisons with full/model-scale pile load tests. INTRODUCTION The influence of pile battering on the lateral response of piles is rarely studied in the literature. Over the last decades and as suggested by Kubo (1962) and Zhang et al. (1999), a p-y multiplier is applied to predict the response of laterally loaded battered piles from an equivalent vertical one. Several researchers conducted model-scale piles load tests to understand the behavior of battered piles subjected to lateral load (Juvekar and Pise 2008; Meyerhof and Ranjan 1973; Meyerhof and Yalcin 1994). However, such tests were conducted on model piles with diameters less than 30 mm which may not have reflected actual soil-pile interaction. Battered piles are generally categorized as positive or negative battered piles according to the angle of pile installation as shown in Fig. 1. From the small-scaled and numerical models of battered piles, it was found that the lateral capacity of negative battered piles is larger than that of vertical ones. On the other hand, the positive battered piles have lower lateral capacity when compared to vertical piles (Fan-ren and Ji-Ming 2011; Juvekar and Pise 2008; Manoppo 2010; Reese et al. 2004; and Reese and Van Impe 2011).

Jan 1, 2018

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991