Search Documents

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Jerry A. Steding

How many times have you heard "You can't drive piles because of the vibration."? You hear these words come out of the mouths of owners, engineers, and contractors. When a piling contractor hears this, he can almost always do a psychological profile of the individual uttering these words of wisdom. If the owner makes the statement, we know the odds are about 95% that the owner owns the building next door or he wouldn't care what happens to it; or the guy next door has threatened to sue the owner if he even so much as walks across the site of the proposed new building. If the owner owns the building next door to the new construction you can also be just as certain the old structure has undergone settlement. If the statement comes from the mouth of the contractor, it is usually just a case of him being inexperienced.

Jan 1, 1988

By Gary T. Brill

In the presentation, the development and new applications of the jet grouting technique in the North America are briefly introduced at first and followed by the outline and advantages of Jet Grouting. Several recent projects for jet grouting are presented in which the applications to underpinning and excavation support, foundation, groundwater barrier and seismic stabilization are briefly discussed.

Feb 10, 2003

By R. K. Filip

"Steel bearing piles have long been used to carry high compressive, tensile and lateral loads. Such piles are most commonly tubular or ""H"" profile and are typically installed using percussive techniques. The noise and vibration associated with such installation techniques tends to preclude the use of steel bearing piles in urban and other sensitive areas.This paper describes the design and construction of an innovative new road bridge in Milton Keynes, UK. The steel bearing piles were required to continue out of the ground to form the bridge columns and abutments and then be cast directly into the soffit of the reinforced concrete bridge deck. This project was to be the first time in the UK, that this form of bridge design had been used.The paper shows how new installation techniques allowed the designers to use these high capacity steel elements in a sensitive urban environment without the use of percussive or vibratory installation techniques. Finally the paper shows how these quiet and vibration-less installation techniques can be extended to other applications.A UNIQUE BRIDGE SUPPORTED ON ""BOXED SHEET PILES""CONCEPT HISTORYThere are over 700 bridges in Milton Keynes. Concrete is the dominant construction material, most are single span with massive parallel wing wall retaining abutments. All have a certain uniformity of aesthetic design. Pell Frischmann Consultants Ltd (PFC) proposed to the client, English Partnerships (EP), that an ""integral bridge"" with a slender open appearance would be an appropriate aesthetic form for a new highways bridge, within the district of Westcroft (figure 1). The concept required that the bearing piles be continued up out of the ground to form the bridge columns and abutments. Four rows with four piles in each row were suggested. Each would then be cast directly into the reinforced concrete bridge deck forming a moment connection (figure 2). This concept meant that a single continuous steel structural member would replace traditional reinforced concrete bored piles, pile caps and piers. This member would carry vertical and lateral loads. The conceptual design was intended to meet the following client requirements:"

Jan 1, 2005

By Ziyad Abunada, David O’Connor, Fei Jin, Abir Al-Tabbaa

"In-situ remediation of contaminated land with deep mixing can enable a multi-technique remedial strategy on the same site combining low permeability barriers, permeable reactive barriers, stabilisation/ solidification treatments as well as ground improvement, delivering significant advantages over alternative strategies. This was the core objective of Project SMiRT (Soil Mix Remediation Technology) which involved the execution of the largest research field trials in the UK to date to provide field validation for this technique. Around 800m3 of soil were treated on a contaminated site in Yorkshire in May 2011 with 6 different treatments, testing ~40 binder compositions and 10 different installation methodologies. Field monitoring, testing and coring activities at the site took place within the first 2 months after treatment and then again at 34 months after treatment. This paper presents an overview of the field activities to date and some 3-year results and assessment of a subset of the treated soil sections. Some good correlations are seen together with some clear differences between treatments. There is generally an observed consistency with depth, with the mixing effectiveness having a more profound effect than the binder composition or content, within the tested materials and ranges. These field trial activities are currently being used in the development of the full-scale commercial remedial strategy for the site.INTRODUCTION AND OVERVIEW OF PROJECT SMiRTWhile there are strong financial and environmental incentives to remediate and redevelop brownfield sites there are also barriers including fear of the unknown, regulatory control, delays, increased costs and the stigma associated with such sites. Hence the remediation process needs to be conducted in such a way to maximise the incentives and overcome the barriers, which is how deep mixing found its niche in the land remediation market. Soil mix technology is such a versatile technique that can perform a number of remediation treatments on the same site. These include low permeability in-ground barriers (cut-off walls), permeable reactive barriers (PRB), stabilisation/solidification (S/S) treatments, other additive related remediation, e.g. in-situ chemical oxidation and bioremediation, as well as soil amendments for greening and also ground improvement all on the same site (Al-Tabbaa et al, 2011). Placed in the context of alternative solutions, soil mix technology could potentially replace the five techniques shown in Figure 1, which would be required to deliver the same treatments mentioned above. Treatment trains strategy, where a combination of techniques in succession are used to both reduce the contamination levels and deal with residual contamination, is becoming common in land remediation and the use of one set of equipment to deliver this would bring about significant financial advantages. In addition, soil mix technology has many other advantages in terms of speed of implementation, elimination of exposure to contamination, elimination of off-site disposal and low cost. Soil mix technology for the remediation of contaminated land emerged in the UK in the mid 1980s and has since been employed in over 30 or so projects, which far exceeds its application to ground improvement for which only a handful of jobs have been carried out to date."

Jan 1, 2015

By Gary L. Seider, Dana A. Wesolek, Fred C. Schmednecht

"A new condominium project, The Atelier, developed by Pickus Companies located at the corner of Bryn Mawr and Sheridan in Chicago, IL required an earth retention system to protect the surrounding roads, alley, and existing neighboring apartment bui lding during its construction. Slurry Systems, Inc. (SSI) and Ground Engineering Consultants, Inc. designed the earth retention system using cantilevered sheet piling for three of the four sides: two sides bordering major streets and one side bordering an alley. For the fourth side, which borders an existing occupied brick building, a combination of sheet pil ing and AB. CHANCE® helical screw piers were used. SSI was actively involved in the review process of its earth retention system with the City of Chicago and quickly learned that there was no specific code for hel ical piers/anchors. (It appears that this is the case with most metropolitan cities throughout the United States). Consequently, the approval of underpinning for this project became the critical path, as much testing, calculations, meetings, and other details were required prior to its approval.SSI and AB. CHANCE® recognized that this process for underpinning approval must be seen by other contractors/suppliers who wish to use helical piers/anchors in the City of Chicago. Consequently, this project served as an opportunity to work with the City of Chicago and the City's Building Code Committee in furthering the development of the Helical Piers/Anchors Code, Section 1814. INTRODUCTION - HELICAL PIERSDefinition. A helical pier or anchor consists of one or more helix-shaped steel bearing plate(s) attached to a central steel stem (solid bar or pipe), which is installed by rotating or ""torquing"" into the ground. Each helix is attached near the tip, is circular in plan , and is formed into a screw thread with a defined pitch. Helical piers/anchors are pre-fabricated and can derive their load-carrying capacity through both end bearing and skin friction. The helical piers/anchors can be augmented with grout."

Jan 1, 2005

By Peter Cali

There is one organization in Sweden, The Swedish Deep Stabilization Research Centre, which has been working with these questions and there is also a project, Eurosoilstab, within European Union to take a manual for deep stabilization.

Feb 10, 2003

By Paul J. Sabatini

Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed. During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor?s QA/QC program should be increased to achieve a foundation system with the required level of reliability. Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially ?at-risk?. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.

By Lynn Crayne

We used Glyoxal as the hardener, at a final concentration of 10% by volume and therefore 20% by volume in the A-Component. They worked pretty well what we did was we shaved the joints on each of the pipes when we assembled them so they wouldn't rip the packers and then we greased the packers very well going in. We had to replace some but we have any getting stuck or didn't lose any pipes.

Feb 10, 2003

By Franz-Werner Gerressen

New developments are required each day as our industry becomes more competitive. To improve performance, continue and to ensure future demands can be met. This requires the development of technical support systems that enable a more constant delivery and quality of installation of pile foundations and other applications. For example: assistance systems capable of relieving the machine operator of automating monotonous or repetitive operations. Real time installation control of the production process to manage quality control, or data transfer and reporting systems capable of keeping pace with the digital future. This paper will describe these new approaches and considerations required for these new developments. The paper also describes the equipment which is needed to execute the work under the various conditions and provides references herein. INTRODUCTION The success of a construction site is influenced by a number of factors. Selecting the most efficient and economic methods during the planning phase to defining the right direction. This means having multifunctional equipment available. To ease the usage of this equipment by the operator, uniform operation and control systems are essential. Systems like this can provide uniform handling procedure for more than 20 different installation techniques. Experienced operators are not always available. Therefore, to ease the start for beginners and to support training, numerous assistance systems were developed. This ranges from simple information for controls shown on the monitor avoiding misuse to systems which can partly automate the construction process. Regardless, the best equipment is not enough when the construction is not running smooth. The control system not only helps to organize and coordinate service of the equipment; moreover, it allows the operator to control the quality during the installation process reacting if needed. It allows process optimization as well as documentation which might be required for later negotiations.

Jan 1, 2019

By Ingrid Engeset, Solve Hov, Arnfinn Endal, Per-Anders Mortensen, Priscilla Paniagua, Bjørn Kristian Fiskvik Bache

During the last decades, it has become common practice in the Nordic countries to use dry deep mixing in soft clays with lime and cement in for example deep excavation pits in soft clay, or as a reinforcement of the passive zone within sheet pile walls. The shear strength of stabilised soils is affected by the stress conditions during curing and shearing. However, this is normally not taken into consideration. As the strength of the stabilised clay is stress dependent, excavation of the overlying soil will lead to a reduction of the confining stresses in the underlying stabilised soils which means that the shear strength will also be reduced. Under embankments on the other hand, the effect is reversed as the shear strength will be increased. In this study, laboratory tests have been performed on stabilised soils cured and tested under different stress conditions to quantify the stress effects in a Norwegian sensitive clay. In addition, direct simple shear tests on samples from in situ columns have been made with varying normal stresses. Results are presented showing an increase of shear strength of the stabilised soil with increased curing stresses, and an even higher increase with increased confining stress during shearing. The results are compared to field measurements along with a discussion of practical application of the findings.

May 1, 2022

By Dennis Wrixon

It was a little bit exceeded. The decision was the uniform settlement is measured at each one corner and the highest one corner is the important one. And in addition there is a differential settlement of 2.1 mm allowed. So we reached about 7.8 or 7.9 mm with the highest corner and in addition 2.1 so it was a little too much. But behind there is a very difficult calculation of the authorities where all of the displacements are combined together and there are of course some more factors of safety in these settlements.

Feb 10, 2003

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By Gregory M. Landry

"There is an old joke at Moretrench that defines dewatering as “that element of an underground construction project, which, when disregarded, will generate the low bidder.” Sigmund Freud wrote that all jokes are true, and the kernel of truth behind this one is that dewatering is often misunderstood or neglected until the last possible moment in the life of a project. The purpose of this article is to describe commonly used dewatering methods and to clear up a pervasive but fundamental misunderstanding about how to determine the amount of dewatering effort required for a project. The Tools of DewateringDewatering may be divided into two broad categories: (1) methods that remove water from the excavation after it has already entered and (2) methods that seek to exclude or intercept the water before it reaches the excavation. The former is generally self-performed by general or earth moving contractors using sumps and ditches, while the latter is usually done by a specialty contractor. SumpsProperly installed sumps can be an effective and economical way to control water inflow into a site. In this technique, groundwater is allowed to enter the site before being pumped away. Advantages of this method include lost cost, easy availability of equipment and the fact that a general contractor can self-perform the dewatering. However, caution should be used when deciding whether to use this method, and consideration should be given to the following factors:1. How will the soil behave under seepage forces? Will it run, potentially causing ground loss?2. How much groundwater lowering is required? If the groundwater only needs to be lowered a few feet, using sumps will be much more practical than for a situation that requires significant drawdown.3. Will the excavation subgrade soften or otherwise be damaged by allowing water to run over it?4. Is my workforce skilled enough to implement and manage the sumping plan?In the photo, the sump is capturing groundwater that has already entered the excavation by traveling under the sheets. In this instance, the house in the background of the photo was eventually purchased by the project owner after sustaining damage due to ground loss."

Jan 1, 2017

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By Lucian L. Bogdan

"SummaryActive loaded strand anchors are often used for slope stabilization, retaining walls or tiedown anchors. Normally, strands are tensioned against the structure and wedges are locked inside the anchorages at a certain lock-off load. During the life of the structure, anchors can receive additional loading during a surcharge, seismic event or other activity on the structure.In order to have a reliable ground anchor system, the strand must not slip through the anchorage wedges during its service life. Strand slippage has been reported during lock-off, when dirty wedge plates and wedges have been used. Low lock-off loads are believed to contribute to strand slippage too. Since the initial lock-off load for a ground anchor is usually lower than the lock-load for an equivalent capacity tendon in other types of post-tensioning construction, there is a concern that strand slippage may occur if the load on the anchor increases above the initial lock-off load.Corrosion protection grout, placed after the anchor is locked off, fills the pocket and surrounds the strand and wedges. Some anchor installers believe that the grout will prevent the anchorage from developing additional capacity if the load increases above the initial lock-off load.The load-carrying capacity of an anchorage depends on several factors. Most important are: initial applied load, anchorage geometry, friction between wedge-anchorage-strand and condition of the contact surfaces.The ADSC Anchored Earth Retention Committee considers that the industry should know how wedges behave once the permanent strand anchors are stressed and grouted inside the transition pipe, between wedges and inside the grout cap."

Jan 1, 2005

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy"

Jan 1, 2017

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy."

Jan 1, 2017

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By John Davie

We used a Remtek survey in Glenrock and had very good luck with it when we first started the initial investigation. We would have loved to have used that more but my understanding is the equipment is hard to find. It also requires a flooded mine workings. If you're in a dry mine the communication between the two holes is not quite as successful.

Feb 10, 2003