Search Documents

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By Michael Frawley, Deana Ruud, Jessica Turner

Technology is allowing for new ways to mitigate risk associated with subsurface exploration and unanticipated subsurface conditions during construction. Unanticipated subsurface conditions have the potential to force delays and cost overruns on even the best-managed and well-executed projects. For more than a century, geotechnical professionals have documented the location and conditions encountered in hundreds of thousands of subsurface borings. Utilizing processes for compiling and managing data, owners can streamline site selection and receive access to a conceptual geotechnical model before field exploration takes place. Digitizing historical subsurface information allows for creation of an interactive, web-based platform combining publicly available information and culminating with the opinion of a local, experienced geotechnical engineer. This connectivity aids in the reduction of risks associated with unknown conditions on prospective project sites. Through this conceptual project study, we demonstrate how a project owner would be able to use a comprehensive desktop study to review the expected conditions prior to making a purchasing decision. Following the purchase, the expected conditions would be confirmed through traditional methods, confirming potentially problematic site conditions and the associated risks. INTRODUCTION Preliminary project planning is often based on assumptions made by the design team with regards to site suitability. After due diligence, site development is traditionally initiated by the owner or the owner’s representative when engaging a geotechnical engineer to perform a thorough subsurface exploration at a site. The data generated by the geotechnical engineer’s analysis of the site is required to design foundations, pavements and earth retaining structures and move the project from concept into design. This necessary, subsurface exploration can be time consuming, intrusive, and require significant resources, often when resources during construction seasons when resources are most limited. By leveraging historical data generated from previous subsurface exploration, a more thorough analysis of project risk can be developed prior to mobilizing a drill rig. Ultimately, preliminary budgets and designs are more accurate and geotechnical field exploration is more strategic. The geotechnical engineer’s role transforms from raw exploration and analysis to confirmation of anticipated conditions.

Jan 1, 2019

By Dominic Ammon, Mark Rothbauer, Paul Landers P. E.

Across the Potomac River from the location of the DFI47 Annual Conference (October 2022), in Alexandria, VA, two large permanent anchored walls with a decorative shotcrete face were recently constructed for the North Hill project, a new multi-family and townhome development. The project was executed with a design-build approach for the Fairfax County Redevelopment and Housing Authority with review by the Fairfax County Geotechnical Review Board. The project was constructed in highly variable Potomac group sediments that include high plasticity clay/silt terrace deposits overlying coarser grained materials. The soils were over consolidated and exhibited potential for slickensides from relief of horizontal stresses from past erosion. The wall system was designed to include deep soldier piles and permanent long strand anchors considering past slope instability in the area. As the construction progressed, problematic soil conditions and water issues required modifications to drilling methods. The two permanent walls spanned 800 and 1,000 feet long with a maximum height reaching 40 feet.

Oct 1, 2022

By Jim Bruce

No answer required. From the drilling equipment suppliers, but the specifications must be tailored to be project-specific. Yes, the sonic technique is very interesting as we said, and it is not so much as an issue of the magnitude of power, it's about the efficient use of the power. The efficiency of the machine is not necessarily related to size so it is best to talk to the two contractors that supply the service about that. I think it can be scaled down but it is quite a big head, so therefore there are practical limitations on the size of the door it can walk through and also the size of the casings and rods that it can use. You might defeat the economic advantages if you were to use too short casing lengths. Boart Longyear have a low head room machine that can work within an 8 foot verical clearance.

Feb 10, 2003

By Jeffrey C. Schuh, Logan Bloemer, Daniel P. Dietzler

Over the past 30 years, the authors have encountered numerous projects where recognizing the geology, soil properties and groundwater conditions, and considering alternative construction techniques have promoted efficient and cost-saving construction. The construction documents for these projects, produced by various engineering firms, provided basic information on geotechnical conditions. The authors became involved in each project either because there was a problem during design or construction or, as a contractor, won the project because they saw a value engineering opportunity to take advantage of the geologic setting of the project to design and build alternatives to what the designer depicted. Understanding the geologic setting is critical before planning and designing begins. Being able to work with the geology and the materials on site is preferred before specifying more costly and complex solutions, which often require the importing of materials and adherence to unnecessary and/or inappropriate specifications. Failing to understand the geology or not knowing all the techniques available for construction can lead designers to develop solutions that could be inappropriate. This paper presents several examples of value engineering and project performance enhancements developed through knowledge of basic soil mechanics and implementing innovative solutions. History and Background Most people attend DFI meetings, present their experiences, listen to others, and read articles and papers with the hope they can learn from others. Geotechnical engineers and contractors often interface with others in the execution of projects who have, at best, a rudimentary knowledge of geology and soil mechanics. Of course, there is a need for architects, bankers, and regulators, etc., but they typically do not have much interest in the nuances of geotechnical engineering, which relies on both art and science. Thus, significant time is spent educating counterparts in the need for comprehensive subsurface investigation programs and the intricacies of construction in the “dirt,” as they typically refer to soil and rock.

Jan 1, 2019

By Thai Nguyen Ph. D

Dynamic Load Test (DLT) on driven piles has been performed routinely all over the world. In several recent projects, even 100% testing has become a norm where every single pile is dynamically load tested. In these cases, most piles are of uniform sections, making the field analysis (CASE method) straight forward. The CASE method, which has been used for the last 50 years, however, is only applicable to uniform piles to monitor pile driving stresses as well as pile capacities. Signal matching analysis can handle different configurations. However, the analysis used to require user inputs (i.e., non-automatic). Manual signal matching analysis, which can solve non-uniform solutions, traditionally takes hour(s) to complete for one blow. As such, the real-time pile driving stresses and resistances had traditionally been relying upon the CASE method, using typical range of CASE damping (JC). Until 2021, due to the lack of a rigorous instant signal matching analysis for non-uniform piles, no tool was available to help engineers evaluate non-uniform piles in real-time. An inexperienced field engineer may overlook this shortcoming when evaluating peak driving stresses. Furthermore, ultimate bearing resistances for non-uniform piles may require further evaluation to account for the non-uniformity of piles if relying on the CASE method. This paper highlights recent advances in instant Signal Matching Analysis on non-uniform piles, allowing field engineers to monitor stresses and resistances of non-uniform piles during driving.

Oct 1, 2022

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By Cemal Can Maslak, Vijaya Bhushan Rao, Vidyaranya Bandi, Karsten Beckhaus

A Large Earth Cum Rock Fill, ECRF Dam is under construction at Polavaram in the state of Andhra Pradesh in India as part of an irrigation project. The Embankment crest width of the dam is 12.5m and base width is of approximately 136.75m with a stepped sloping height of 27m on both upstream/downstream sides. Once the 1.2m Thick Plastic concrete cut-off wall is constructed below the dam along the longitudinal central axis to avoid seepage, this magnificent structure will be supported on a series of Deep Mixing Columns and Stone Columns that are evenly arranged under the footprint of ECRF Dam forming a smooth transition of gradually reducing stiffness moduli of treated ground from the center of the embankment, where the foundation stresses are high, towards the edges in order to be able to progressively limit the settlements under the dam to a specified allowable limit. As such the required post treatment stiffness in case of stone columns is 2 times of the in-situ stiffness of foundation soil, whereas it is expected to be 5 times improvement for Deep Mixing as per project specifications. Laboratory testing and Field Trials undertaken successfully to verify the design.

Sep 1, 2022

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement. This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects. The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied. The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2015

By Francis B. Gularte

The Dalles Dam is located 192 miles upstream from the Columbia River?s mouth. As part of an effort to increase survival rates for young salmon migrating downstream to the Pacific Ocean, a river spillwall was constructed to guide the young salmon into the thalway and out of the reach of predators. The spillwall consisted of 43 large precast concrete cells constructed onsite. The 120-ton cells are positioned on the bedrock riverbed to form the 830-foot-long spillwall. Large capacity post-tensioned strand anchors extend through ducts in the precast units, anchoring the wall to the basalt. One hundred seventy-eight tie-down anchors consisting of 30, 32, or 40 strands were installed and post-tensioned to secure the cells. The logistic and technical challenges presented by positioning, installing, and stressing the precast cells in the tailrace of a large dam required a high level of cooperation and planning between the owner, general contractor, subcontractors, and suppliers in order to finish the project within the allotted in-water work windows to minimize impacts on seasonal salmon migration.

Jan 1, 2010

By Seyyed Mehdi Radeghi Mehrjou

It is important to study structures and their retrofitting techniques in order to avoid earthquake-induced seismic damage within countries that are prone to earthquakes. Todays, micro piles are employed as useful structural components for seismic behavior improvement. The present study analyzes inclined micro piles subjected to seismic loading by using the three-dimensional finite difference method (FDM). FDM assumes an idealized three-dimensional soil-micro pile model to perform logical behavior evaluation in the event of an earthquake. Linear and elastic micro piles and elastoplastic soil were employed in this study. The Mohr-Coulomb criterion was employed in the failure control of the micro piles. The micro piles were subjected to the 1978 Tubas earthquake records. The numerical results were compared to experimental data. The comparison revealed good agreement between the numerical results and experimental data. The inclined micro piles were found to sufficiently enhance soil strength under seismic loading, inducing smaller displacements than vertical micro piles. Furthermore, the soil and inclined micro piles showed salient interaction.

Sep 1, 2022

By Brian M. Fraley

"Portions of the Catholic Total Abstinence Fountain in Fairmount Park in Philadelphia, Pa., were in “imminent danger,” according to a restoration services request for proposals (RFP) issued by the City of Philadelphia in August 2014. Open voids in the subsurface beneath the foundation were causing ongoing settlement of the fountain.The fountain was unveiled in 1876 as an ornamental drinking fountain for the Centennial International Exhibition, which celebrated the signing of the Declaration of Independence. Its creation was commissioned by the Catholic Total Abstinence Union of America, an Irish temperance organization that advocated for total abstinence from alcohol. Ironically, the fountain ran dry decades ago.The now-defunct fountain features a 100 ft (30.5 m) wide granite base with three steps in the shape of a Maltese cross. The centerpiece — enclosed by a 40 ft (12.2 m) diameter basin — is a 15 ft (4.6 m) tall statue of Moses perched atop an iglooshaped marble mound. Four subsidiary statues rise from granite pedestals at the tips of each arm of the cross, including Archbishop John Carroll, Charles Carroll of Carrollton, Father Theobald Mathew and Commodore John Barry.Natural and Man-Made DamageThe City of Philadelphia’s RFP called attention to three “high priority structural areas.” It was noted that Moses, Father Mathew and the steps surrounding the fountain had been documented as public hazards. The long-term effects of water infiltration had set in, eroding mortar joints and causing some stones to jut out. Furthermore, the stone base supporting the 16 ton (14.5 tonne) statue of Moses was in danger of collapsing. The statue of Father Mathew had been struck by lightning in 1910 and was repaired with an iron and metal pin anchor system, which had succumbed to corrosion. The city considered the statue of Father Mathew as the most threatened of the statues. Mike Miluski, P.E., vice president of Compaction Grouting Services (CGS), recalled “the fountain was in pretty bad shape” as he walked onto the site in August 2016 and immediately recognized the challenges ahead."

Jan 1, 2017

By Peter Middendorp, Gerald E. H. Verbeek

"This paper will describe a brief history of the method of characteristics as an accurate solution of the wave equation, and the author's experiences with the method of characteristics over a period of 30 years.As a result of the offshore pile driving activities associated with the development of the North Sea oil fields in the 1970's, two Dutch companies initiated extensive research efforts. Heerema started to research the dynamic behavior of soil during driving and HBG (Hollandsche Seton Groep) extended the method of characteristics with a straightforward theoretical solution for the shaft friction along a pile.The research institute TNO started the development of the wave equation program TNOWAVE in the late 1970's based on HBG's friction model extension for the method of characteristics. Today the program has a worldwide application in the field of pile testing. This paper will describe its development and application over time and its relation to today's applications for driveability studies for impact hammers (PDPWAVE) and vibratory hammers (VDPWAVE), signal matching for Dynamic Load Testing (DL TWAVE), Pile Integrity Testing signal matching (SITWAVE), and Statnamic simulation (STNWAVE).The paper will highlight that these developments have been the result of multi-disciplinary and multi-national efforts and encourage geotechnical engineers to seek further developments of the wave equation program in a similar manner. Finally, the paper will indicate some areas where such further developments are required."

Jan 1, 2005

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By A. Flora, E. Bilotta, F. Foria, V. Nappa

"All the typical applications of deep mixing rely on the good mechanical properties of the improved columns to strengthen or stiffen the ground for a number of geotechnical applications.This paper focuses on a completely different kind of deep mixing, carried out in order to obtain columns much softer than the surrounding soil. This kind of deep mixing, named Soft Deep Mixing (SDM), is introduced as an original means to tackle seismic risk, and can be convenient when the existing structure to be protected has a historic relevance that cannot be altered with structural modifications. The idea is that properly assembled layers made of partially overlapped SDM columns, with dynamic impedance much smaller than that of the surrounding soil, will filter and reflect most of the seismic energy.The paper presents the results of some 2D parametric numerical analyses aimed to investigate the seismic performance of this innovative approach. Simplified dynamic inputs (Ricker wavelets, having only one largely predominant frequency) were adopted to better understand the effect of signal frequency. The analyses show that the effectiveness of the soft grouted isolating barrier depends on soil and SDM geometrical, physical and mechanical properties, as well as on the frequency content of the seismic input.INTRODUCTIONPassive structural systems installed at the foundation level of existing buildings are a common solution to protect them against earthquakes. However, installation procedures are expensive and not always feasible, as for instance in the case of valuable buildings. As an alternative, ground improvement techniques can be used to modify ground properties, in order to mitigate the intensity of shaking at ground level. The propagation of shear waves in the ground can be modified by introducing a layer of artificially modified material, having a dynamic impedance (defined as n =p VS, where p is the material density and VS the velocity of shear waves) very different from that of the natural soil. Both very high or very low values of the dynamic impedance of the grouted soil (nt) can be effective in reducing the overall transmitted energy, with the difference that – for a given reduction of the transmitted energy - stiff grouted layers tend to filter the low frequency components of the amplitude spectrum without modifying in a significant way the high frequency components, while soft grouted layers have the opposite effect. Then, ideally the choice of the best grouting technique should be made considering the effects of the different frequency components on the building to be protected. These effects are detrimental for the structure when they are close to its natural frequency: high frequency components result into large structural loads on massive squat structures (high natural frequency), and low frequency components may be critical for tall and flexible structures (low natural frequency). Therefore, the typical procedure of stiffening the uppermost soil layers regardless of the kind of building to be protected is not necessarily beneficial, and for the case of squat structures soft grouting should be preferred. However, this procedure has not been taken into account yet in the engineering practice, and may pose static problems at ground level (i.e. excessive static settlements)."

Jan 1, 2015

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By N. Schmitz

This paper explains how new digital solutions improve reverse circulation drilling operations. Upgrading field-proven reverse circulation drilling (RCD) rigs with new digital technologies enables semiautomated drilling, with upgrade options for fully automated & remote drilling. Key elements of the improvements are electrically controlled valve systems, process instrumentations, a state of the art machine controller and drilling operation via a touch control panel. Automation of core processes, such as adding drill pipes, reduces set-up times, increases machine uptime for drilling and as a result efficiency. While drilling, sensors provide continuous feedback, which is used to automatically adjust e.g. the weight on bit to the optimum; resulting in an increased rate of penetration and less wear and tear. While in the past hydraulic power packs (HPU) have typically been operated at a constant high-performance level with related high fuel consumption, a new interface between the machine controller and the power unit regulates the HPU performance exactly according to the actual drilling operation needs. This leads to significant fuel consumption reduction. The safety benefits of the digital improvements are the ability to remotely operate the rig in challenging site conditions via a mobile operator panel.

Sep 8, 2021