Search Documents

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

By Michael P. Amsden

"THE ECSTALL CONCENTRATOR is situated adjacent to Highway 101 and the Ontario Northland Railroad, 15 miles east of Timmins, Ontario. Ore is delivered to the concentrator by rail from the mine, which is 17 miles northwest of the plant. Power and fuel are obtained from the hydro and natural gas lines which pass close to the plant site. Water is obtained from the Frederickhouse River, 6 miles east of the concentrator. The main concentrator building is a large structure 500 by 640 feet by 90 feet high and contains facilities for fine crushing, crushed ore storage, grinding, flotation, tin recovery, concentrate handling and reagent handling. Located in the same building are the machine shop, warehouse, metallurgical laboratory, pilot plant, men's change room, sample preparation area and an assay laboratory. The general concentrator layout is shown in Figure 47. Originally designed to handle 9,000 tons per day, the concentrator now treats 10,000 tons per day. Two different ore types are processed by selective flotation in three individual circuits to recover copper, lead and zinc concentrates. In 1973, another circuit was added to recover pyrite and tin concentrates from the combined zinc tailings of the three main circuits."

Jan 1, 1974

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By J. P. Sancho, L. F. Verdeja, J. I. Verdeja

"This paper analyzes the present state of the different processes competing to keep their market shares within the future iron and steel business sector.The continuous transformations in the steel making process are also studied here. These transformations have happened especially during the two last decades obviously favouring steel price, properties, quality and environmental compatibility in the new millennium. IntroductionIn the early 1980s, world steel production reached a historic figure; specifically in 1982, the amount was 645 Mt (Verdeja et al., 1993). This might have been one of the reasons why the United States, Japan and the European Community drew up a declaration of principles after which the leading industries and sectors in the following century’s development would be: advanced materials, also known by the very diffuse term of new materials; information technologies; and biotechnology (Eager, 1998).On the threshold of the 21st century, it can be inferred that information technologies (computers and telecommunications) have progressed spectacularly. Nevertheless, there have been downsides too; technology develops so quickly that after a few months the products are obsolete. Environmental problems may also appear in a few years due to storing so many useless devices. At the same time, the achievements of biotechnology did not meet the optimistic forecasts made in the early 1980s.On the other hand, it is also curious that some solutions for the environmental problems generated by star technologies of the new millennium, such as computers and biotechnology, are closely linked to the iron and steel industry. For example, blast furnaces in Germany and Japan are prepared for burning residua by introducing polymer materials from computers and other electronic prepared devices through their tuyeres, while cement tube furnaces can destroy any organic residua from different origins."

Jan 1, 2002

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

Over the last three decades, the mining industry has been moving towards more underground mechanized mining methods and the number of LHD vehicles utilised has increased. The growth of mechanization and automation has benefited both workers and the mining companies. However, due to the design of the LHD vehicle and the limitations of the operating environment, restrictions to operator visibility are inevitable. The inability of the equipment operator to see clearly (i.e. people, objects or hazards) around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, visibility assessments for existing machines are traditionally completed in the field using a light filament technique. Past researchers have used the light filament technique to collect obscuration zones around the equipment and to produce a 2D chart of this information. The 2D shadow diagrams have proved to be useful in highlighting potential equipment problems and have been performed repeatedly to show the potential of redesigning a part of the LHD for improving visibility. The light filament method involves manually collecting data and requires a level of judgment to be used. As a result the method is susceptible to errors and requires around three hours to complete. The objective of the current research is twofold; firstly to develop a rapid method for field visibility data collection using a laser scanner and secondly to compare results of repeat tests for both light filament and laser scanning methods. A MENSI GS100 laser scanner along with Pointscape and 3Dipsos software has been used to collect visibility information and process the data. The research aims to develop the laser scanner as a technique to rapidly evaluate the visibility profile of an LHD vehicle. Machine design changes can then be assessed quickly using these results.

May 1, 2004

By L. J. Vincze

The high cost of constructing mineral processing plants in remote locations warrants a close examination of the alternatives available for reducing the amount of on-site construction work. Among the alternatives are portable process plants, modular design and barge mounted plants. Each alternative has certain advantages as well as limitations depending upon specific conditions. On the basis of practical experience and engineering analysis, the paper examines the potential benefits to be realized by these techniques and summarizes the conditions required to obtain them. The potential savings indicated by such studies should encourage consideration of innovative design features for new plants located in remote areas.

Jan 1, 1980

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975

By Bob Robinson

In 1990, the European Space Agency (ESA) initiated a technology transfer program to stimulate the wider use of technology developed by the European and Canadian space communities. This paper focuses on the method of technology transfer from the space industry to terrestrial industries, with a focus on the mining resource sector within a program called the Harsh Environments Initiative (HEI) created in 1997. Other resource sector applications include forestry and oil & gas. C-CORE in partnership with the Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) supported by ESA, Canadian Space Agency (CSA) and European R&D organizations conduct projects to promote and demonstrate the transfer of innovative technologies from space to non-space industries. Space programs have and continue to develop new knowledge for extra-terrestrial application, e.g., satellite earth observation, manned missions and unmanned planetary exploration. Many of which hold the potential for application on land and ocean. Currently, space technologies of interest to the mine sector range from robotics and image analysis to sensors, software and advanced materials. The HEI works to identify and apply these types of technologies in the areas of automated/tele-controlled mine operations and mine monitoring.

May 1, 2001

By F. Flynn, P. Downey, G. Ritson

"Bell Creek Mill which has been in continuous operation since 1987 has undergone numerous operational changes in the past three years. The addition of over 2. 5 million tons of resource at over 13 git from Hoyle Pond Mine precipitated an expansion program for the Bell Creek Mill. This paper discusses the major changes that have occurred over the past two years to increase throughput and efficiencies. In addition, the refractory ore treatment options are also discussed.IntroductionThe Bell Creek Mill is located in the Timmins Goldcamp approximately 8km NE of porcupine Ontario. (Fig I.)The mill was originally constructed by Camamax in 1987 to treat the Bell Creek ore at a design throughput of 350tpd. The flowsheet (Fig 2.) consisted of two stage crushing, grinding, thickening, leach and drum filtration with gold recovery by Merrill Crowe.As ore depleted at Bell Creek, the Mill was purchased by Falconbridge to process ore from their Hoyle Pond property. Kinross purchased the Hoyle Pond property and Bell Creek Mill from Falconbridge in 1992.The successful exploration program at Hoyle Pond has led to several expansions and process design changes, with further changes planned over the next twelve months.In 1994, the mine produced 61,865 oz. of gold at an average cost of 197US$ per oz. In 1995 production was 91, 611 oz. at a cost of 187US$ per oz. Projecting the nine months ended September 30, production for 1996 will be 155,000 oz. at a cost of 165US$ per oz.In early 1997, the CIP expansion will be complete, with a target of 175,000 oz. at a cost of 176US$ per oz for 1997. The mill throughput will have increased from 400tpd to 1500tpd between 1994 and 1997.The changes to Bell Creek since 1994 have been numerous with very little of the existing equipment still in operation. The total cost of the expansion to date is 15 million C$. This paper discusses the major projects carried out during in this time. The focus will be to highlight the justification of each project, the design and engineering, some of the initial start-up problems and solutions.Figure 3 shows a plan of the existing mill facility together with the various additions that were carried out."

Jan 1, 1997

By E. LaRocque

"Denison Mines Limited has been processing uranium ore in the Elliot Lake area since May of 1957. The ore body is located i11 the Huronion sediments on the north limb of the Quirke Lake syncline. Minerals of metallurgical significance are brannerite, uraninite and monazite. Gangue minerals include quartz, chlorite, sericite, pyrite, pyrrhotite and rutile. Silica content of the ore is greater than 75 % and pyrite-pyrrhotite content around 7 %. Specific gravity of the ore is 2.75.The Denison flowsheet is based on sulphuric acid leaching to extract the uranium values from the ore followed by liquid-solid separation to wash the uranium-bearing solution from the barren ore. The resultant pregnant solution is concentrated and purified by ion exchange followed by two-stage precipitation with ammonia to produce an ammonium yellow-cake.Elliot Lake ores require high acid concentrations and high temperatures to extract the uranium from brannerite and monazite. Uraninite will leach at low acid concentrations as long as oxiclizing conditions exist. The whole ore must be treated so that these conditions do exist.This paper provides a description of the leaching process equipment as originally installed and major changes in that equipment to date. Process control refinements to economically improve extraction are also discussed."

Jan 1, 1979

By 12670

The Cigar Lake project will develop the world’s second largest high-grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the highgrade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2006.

Jan 1, 2004

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By G. M. Carr-Harris

"THE SUBJECT of permanent molding has received a great deal of attention in the technical press as illustrated by the many excellent articles in the bibliography which follows. In general, this covers the period 1940-1958 and is merely representative of what is available. Numbers in •brackets refer to items in the bibliography.It may be desirable at the outset to give a few definitions covering those terms directly related to this subject. The following is a definition of permanent-mold casting as given by J. W. Meier in a paper, ""The Non-Ferrous Metals and Alloys"", read before the Ottawa Valley Chapt.er of the American Society for Metals:""Permanent Mold Casting is used where a large number of castings of the same part are required and higher mechanical properties, greater density and closer tolerances are essential. Since metallic mold s are very expensive, the number of castings must be sufficient to, defray, at least partially, the added expense. Molds are usually made from a good quality cast iron, 1but other mold materials, such as the aluminum and copper alloys, graphite, ceramics, etc., are being used in certain cases. Important factors in permanent mold casting are the mold temperature; the proper mold dressing; and, as in all other casting methods, the mold geometry, that is to say, the design of spruces, gates, risers and vents""."

Jan 1, 1960

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004