Search Documents

By LeRoy A. Thorssen

The use of lightweight aggregate as a constituent of concrete is not a recent development. Pumice was used by the early Romans, in pozzolana cement concretes, in the construction of many of their works. However, the recent development of manufactured lightweight aggregates, such as the expanded shales, vermiculite and perlite, has created a possible use for a whole new group of Portland cement concretes. Concrete can now be produced with unit weights ranging from 30 to 150 pounds per cubic foot and with various insulating, fireproofing, acoustical and structural properties. The tonnage of such materials being used has increased considerably in each of the past ten years, and can be expected to increase for the next several years as availability of the aggregates becomes more widespread and the properties of such concretes become more thoroughly investigated and more generally known. LIGHTWEIGHT aggregates of many types have become avail-able to the construction industry in most localities on this continent

Jan 1, 1963

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By G. Simard, D. Boudeville, A. Leclerc, A. Boivin

"The objective of this work is to study the various parameters that affect the overflow clarity of gravity settlers used in the precipitation circuit of alumina hydrate from the Bayer process. A mathematical model incorporating the size distribution of the feed suspension (Multi Size Group model), its diphasic nature (Schiller Naumann model) and the presence of turbulence (Shear Stress Transport model) has been solved numerically using ANSYS-CFX software. Preliminary results indicate that the overflow clarity is mainly controlled by lateral diffusion of fine particles (~20µm) from the exit of the feed well and by their upward transport from the sediment bed interface. Also the turbulence pattern in the settling zone seems to play a significant role in this vertical transportation. The validity of the model has been verified by comparing the measured solid concentrations from a pilot classifier with the calculated ones. This model could provide mineral processing plant operators and designers with a tool to optimize the configuration of classifiers with respect to the overflow clarity.INTRODUCTIONProblemIn the Bayer process, alumina hydrate precipitation from the saturated liquor is initiated in settler by adding crystallization seeds. Most of the precipitated alumina settles to the bottom of the tank while the liquor and the remaining alumina rise to the top, where they are removed at the overflow. Ideally the overflow clarity, which depends on the operational mode of the classifier, should be controlled within targeted limits."

Jan 1, 2016

By D. Pérez Escobar

Multiphase steels are quite sensitive to hydrogen embrittlement. Laboratory tests to evaluate this often use electrochemical, charging to introduce hydrogen into the sample, but damage purely caused by hydrogen charging has to be avoided. A ferrite-bainite steel, was charged using various conditions to identify when surface blisters occurred. Samples were also checked for internal, damage by electron microscopy. This study was repeated for three other multiphase steels and pure iron. An HSLA steel, was found to be more resistant whereas pure iron was quite susceptible to internal, hydrogen damage. For al, industrial, steels, cracks concentrated in the middle of the sample were attributed to inclusions and segregations, inherent to production.

Jan 1, 2010

By W. Holyk

"Although lead, zinc, copper, and iron sulphides have been known for many years in the Bathurst region, the existence of large massive deposits was not known until the discovery of the Brunswick orebody in 1952. This was followed by the discoveries of the Anacon orebody in 1953 and the American Metals orebodies in 1954. There is no question as to the great importance of these large massive sulphide deposits, and no doubt that other sulphide deposits are to be found. The problem, of course, is where and how to find them.The discovery of the Brunswick and Anacon orebodies is attributed to geophysical work. The original discovery of the American Metals deposit is generally attributed to a regional airborne electromagnetic survey.It is generally stated that the Bathurst area is a geophysical camp, and this is essentially true, but in this highly competitive search for orebodies it is obviously impossible for an individual company to cover the entire area by a comprehensive geophysical survey. Some means other than geophysics must be used to narrow the target. The quickest, cheapest, and simplest method is geological investigations.It has been stated that nothing can be accomplished by geology in the Bathurst region, since the camp is largely covered with overburden. This is true only insofar as detailed work on certain properties is concerned. It is not true of the larger regional picture. Outcrops are scarce, but angular float is abundant, and precedent shows that angular float has moved but a short distance from its source.GeologyAeromagnetic maps published by the Department of Mines and Technical Surveys are the best guides to the geology and structure of the area. These maps supply factual information concerning the underlying rocks. When coupled with field investigations, they are very useful in the interpretation of regional geology and the selection of favourable areas. The discussion of the geology is accordingly centred upon the aeromagnetic maps. The following is essentially a working theory, based on geological facts as best reconciled with all other available information,"

Jan 1, 1949

By Masatsugu Morimitsu

This paper introduces new technology of oxygen evolution anodes which can be applied to produce copper, zinc, cobalt, and other metals by electrowinning. The anode consists of nano iridium oxide particles dispersed in amorphous tantalum oxide matrix as a catalytic layer formed on a titanium substrate. The anode can reduce oxygen evolution potential by 0.25 to 0.55 V compared to commercially available lead alloy anodes and can suppress unwanted side reactions such as manganese oxyhydroxide, lead oxide, cobalt oxyhydroxide which occur during oxygen evolution in the electrowinning solutions. This technology is effective for environmentally friendly electrowinning processes with low energy consumption and less anodic deposition.

Jan 1, 2011

By W. R. McQuarry, M. E. Wilson

"The structural relations of the ore deposits of the Staclacona mine are of considerable interest, for they not only illustrate the effect of a change in competence of the wall-rock, but also the effect of either the convergence together of two faults, or a change in the clip of a fault, or both of these factors, on ore deposition.The mine is in claim M.L. 1818 near the eastern end of Pelletier lake and lies about 2 miles south of the town of Rouyn. The Company was organized in 1926 to explore claims in Rouyn, Dufresnoy, and Beauchastel townships, but attention was directed mainly to those in Rouyn. Underground work began in 1928 with the sinking of the main shaft to a depth of 300 feet. Except for 1930 and 1931, the mine has been in operation continuously since that time. Production, which began in 1936, up to the end of 1946 has amounted to 1,381,422 tons of ore from which gold and silver having a total value of $7,861,860 were recovered. The average grade of the ore milled in 1946 was $6.68.GEOLOGYThe rocks in which the Stadacona ore deposits occur are mainly volcanics of the (Keewatin) Abitibi series intruded here and there by numerous dykes, sills, or masses of diorite. Single dykes of olivine diabase and lamprophyre are also present in the property and are intersected in the mine workings. The volcanic rocks are part of a wide belt of northward dipping lavas and pyroclastic rocks, having a thickness of over 16,000 feet, that extend from the east-west trending belt of Timiskaming sediments on the south northward to the Horne Creek fault and form the south limb of a large syncline. The volcanic rocks within the property consist of numerous, east-west trending, northward dipping flows of andesite and a few flows of rhyolite interbedded with rhyolite ruff and agglomerate. The angle of dip throughout most of the property is 60° to 80°N., but in the main cross-cut on the 850- and 975-foot levels stratification in rhyolite tuff was noted dipping 35°N. The tuff at this point lies above an intrusive mass of diorite and it is probable that the change in dip results from the way in which the tuff and agglomerate have been thrust aside by the intrusive."

Jan 1, 1954

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab's Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By L. Dufourm

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By M. Kellner

Due to continuously growing resource demands and increasing requirements for sustainability, safety and environmental protection on the other hand, the mining industry is being subjected to these additional requirements. Over the past few decades progress has been made in all topics. In 1987, the United Nations published the following in the Brundtland Report: ?development that meets the needs of the present without compromising the ability of future generations to meet their own needs.?[5] The term ?Blue Mining? means to work sustainably, economically, ecologically, and efficiently while also improving ergonomics, for example by increasing automation. An example of how mining can actively be involved in energy management will be shown. Initial evaluations of underground cavitites were done for purpose of energy storage. The planning and construction of underground pump storage plants both in active and inactive mining operations was also investigated.

Aug 1, 2013

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By W. L. Uglow

In recent years, the microscope has come to be recognized as a valuable aid to engineers whose business is the discovery, development, concentration or reduction of metallic ores. In many of the large treatment plants microscopical research has already an important status; and in the hands of efficient operators the microscope has indicated methods of solving ore problems resulting in the saving of thousands of dollars that otherwise might have been lost in tailings, or expended in freight rates or smelter charges. Failure to procure all the information that the microscope can supply concerning the physical and mineralogical characteristics of complex ores has in many cases led to the construction of unsuitable concentrators, just as the failure to investigate in detail the geological conditions of an ore deposit has often results in the squandering of money on shaft sinking, and mechanical installations which subsequent development of the deposit failed to justify. The great progress recently made in the selective separation of minerals by means of the various processes of flotation and leaching brings strongly to our attention, the scope of the field in which microscopical methods may be advantageously employed. The microscope enables one to observe the minute details of rock, ore, gangue, concentrate, tailing, matte, slag and metal, that are invisible to the naked eye. Furthermore, the technique of microscopal research has been so highly developed that a microscopist can not only observe, but deter-mine the compositions and measure the diameters of the mineral constituents in the ore to be treated. Magnifications of these constituents up to 3,000 diameters may be produced by the proper combination of eyepiece, objective, and projection apparatus, and the images thus viewed may be photographed through the microscope, and permanent records made of them.

Jan 1, 1924

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016