Search Documents

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By Jun Shan

The preparation of poly(N-isopropylacrylamide)-monolayer-protected clusters (PNIPAM-MPC) of gold nanoparticles was carried out in a homogeneous phase using three ways, in which three types of PNIPAM ligands were employed. The first type comprised of PNIPAMs with narrow molar mass distributions, synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and thus, bearing a dithiobenzoate at the chain end. These polymers were used directly to passivate the gold nanoparticles upon the Schiffrin reaction in a one-pot synthesis. The second type of ligands was derived from the first one through hydrazinolysis, and they therefore contained a thiol end group. The third type of ligands was PNIPAMs obtained through conventional radical polymerization, post-modified to contain thiol end groups. The PNIPAM-MPCs were characterized by high-resolution transmission electron microscopy, and by dynamic light scattering. The one-pot synthesis utilizing the ligands of the first type turned out to be a simple and facile method, compared with the other two ways, with which the size of the gold nanoparticles can be easily manipulated mainly by adjusting the molar ratios of PNIPAM / HAuCl4. PNIPAM is a more efficient ligand to stabilize the gold nanoparticles in water and in organic solvents than alkanethiols. The surface density of PNIPAM chains ranged from 1.8 to 3.6 chain/nm2, which is much lower than that typical for alkanethiols. The thickness of a PNIPAM monolayer bound to the gold core is somewhat larger than the size of the random coil of corresponding free PNIPAM in aqueous solution, which suggests that the conformation of a PNIPAM chain bound to the gold core is to extended.

Oct 1, 2003

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By O. S. Perry, G. H. Charlewood, K. Griffin, S Ogryzlo, H. Hopkins, G. MacIntosh

"The gold mines of Kirkland Lake are in Teck township, Timiskaming district, Ontario, latitude 48°9'N. and longitude 80°3'W., at an elevation of 1,038 feet above sea-level.There are seven contiguous producing mines in a length of 3;1/2 miles along the general east-west strike of the deposits. The seven mines are, in order from west to east, Macassa, Kirkland Lake, Teck-Hughes, Lake Shore, Wright-Hargreaves, Sylvanite, and Toburn.The first discovery of gold in the zone was made by W. H. Wright in 1911 on the east claim of the Wright-Hargreaves property, and the following year the Tough brothers and H. Oakes found gold in what is now the No. 1 vein_ at the Toburn. Production began at the Toburn in 1915, followed by Teck-Hughes in 1917, Lake Shore in 1918, Kirkland Lake Gold in 1919, Wright-Hargreaves in 1921, Sylvanite in 1927, and Macassa in 1933.To the end of 1946, 31,938,350 tons of ore had been milled at the Kirkland Lake mines, from which 16,132,700 oz. gold, having a value of $498,517,600, were recovered. The bullion varies from mine to mine between 800 and 900 fine, the average for all the mines being 853. The average fineness of the native gold is 941.The workings of some of the mines are more than 6,000 feet deep and sinking to depths below 7,000 feet is now in progress.GENERAL GEOLOGYThe regional structural geology of the area in which the mines of Kirkland Lake occur is described in a preceding paper in this volume by J. E. Thomson."

Jan 1, 1954

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By G. O. Crowell

This paper gives the history of the celestite deposit, now being mined by Kaiser Celestite Mining Ltd., near Sydney, Nova Scotia. Mining and milling procedures are covered, and the regional and local geology of the area are described, including the origin of the celestite.

Jan 1, 1971

By Robert E. McIvor

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency also has been used extensively by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which is appended hereto. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided.Comminution is responsible for a major portion of mineral processing plant energy consumption and operating costs. Bond Work Index efficiency provides valuable means, first, for benchmarking one’s plant performance against others in the broad industry, and hence defining the extent of the opportunity for improvement. Secondly, improvements in circuit efficiency with implemented changes can be quantified and monitored as part of continuous improvement efforts. These two important business activities are thus facilitated, and, in the absence of any other accepted method, otherwise would be lacking without the existence and application of this standard for comparison. While often loosely applied in the past by plant metallurgical staffs, the increased precision offered by this guideline provides much clearer definition of both the conceptual and statistical meaning of these measurements. Even a small improvement can be enormously financially important, but only if differentiated by measurement. This guideline was thus intended to provide industry improved means to differentiate comminution circuit efficiencies. Carbon footprint reduction is coincidental, but nevertheless can be substantial.The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies."

Jan 1, 2016

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By Z. Pilecki

This work concerns the identification of weak zones in the structure of a rock mass endangered by outburst of gases and rocks in the Rudna copper ore mine at greater depths (approximately 1200 m). A special methodology has been undertaken for the recognition of that threat in the wake of an outburst in the mine in 2009. No similar phenomena have been previously recorded in KGHM Polska Miedz copper ore mines. The research described in this paper was carried out in the new part of the deposit prepared for mining. Geophysical methods were used: seismic tomography and borehole ground penetrating radar (BGPR), along with particular identifications using geological engineering methods. In the researched area, Permian layers of sandstone and shale clay (Weissliegendes formation) and of Zechstein dolomite (top of Rotliegend formation) and anhydrite occur in the copper ore deposit. The rock layers are characterized by variable thickness and intensity of mineralization, varying internal structure, and local fracturing containing different gases and water. It is assumed that accumulation of gases occurs in the tectonically fractured dolomite. The study was focused on the recognition of the structure and properties of the dolomite layer lying directly within the roof of excavations. The first tests were performed with seismic tomography for the recognition of anomalous changes in the elastic properties of the rock mass. The results of these studies were used to design a control borehole for a detailed geological engineering assessment and BGPR surveys with 100MHz antennas. Seismic tomography enabled the identification of changes in Pwave and S-wave velocity, the Vp/Vs ratio, dynamic Poisson's ratio and dynamic Young's modulus. It was clear that seismic anomalies required verification by other methods. The BGPR survey was performed in a specially designed borehole, passing through the selected seismic anomalies. While the borehole was being drilled, the outflow of gases was identified, with varying amounts of CH4, CO2, and H2S detected, as well as water outflow. The results of BGPR confirmed the location of a reservoir of water and gases, about 30 m in length, found in layer of dolomite. The direct cause of the BGPR anomaly was assumed to be intensive fracturing, a greater content of clay material in the dolomite, and the presence of water in the fractured zone. The BGPR image was correlated with information on lithology, fracturing based on the RQD index and additional information acquired during drilling about water and gases surveys and other symptoms. The achieved results also showed a very strong correlation between the location of the zone containing gases and water and the anomalous S-wave velocity and field of dynamic Poisson?s ratio, and to a lesser extent other seismic parameters. It was found that the other measured seismic anomalies may be of the same nature as those identified in the control borehole and accordingly will require the implementation of detailed identification. The performed tests have also shown the usefulness of geophysical methods to identify geodynamic hazards under the geological and mining conditions of the copper ore deposit in the Rudna mine.

Aug 1, 2013

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By M. Vaccarini

In this paper a possible methodology to supplement a predictive control approach is reported. The benefits deriving from the application of a predictive control on complex buildings lay on its capability of adapting in advance to the conditioning needs of indoor environments. In fact, the mere reactive control is usually affected by response delays, mainly determined by latency intrinsic in systems and by the massive nature of buildings, which slows down their response to changeable inputs. Hence, systems are too often solicited at their maximum power to recover against comfort deficiencies, and high consumptions are had. This paper reports on the application of a predictive approach to the Passeig de Gracia (PdG) metro station in Barcelona, which is a considerably high energy demanding building and where ventilation systems are used to control both comfort and air quality. Although an extensive simulation for estimating energy savings obtainable through that approach is currently ongoing, in this paper we detail the several components which make up a ?predictive control framework? and we perform a preliminary demonstrative simulation. In particular, the whole setup is formed by: a detailed model of PdG, which simulates the station?s ?real state?; a control model, which optimizes a given cost-function; probabilistic predictive models to infer the future state of the systems, given the assumptions on the control actions by the control module. The outcomes of this paper show that the procedure is applicable and preliminary results over a short simulation horizon of half a day are reported.

Aug 1, 2013

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By Louise Grondin

Laronde Mine has been working for a number of years to identify substances that could contribute to process water toxicity and to find an effective way of removing these contaminants from the water. Initial studies have identified ammonia, nitrite, cyanide, thiocyanate, cyanate, dissolved organic carbon, copper and zinc as potential toxicants. Bench-scale tests were carried out with Lakefield Research to find a water treatment process that could effectively remove the suspected toxicants. Nine treatment processes were evaluated: 1) granular activated carbon (GAC) filtration followed by zeolite, 2) zeolite filtration followed by GAC filtration, 3) aeration followed by GAC filtration, 4) multi-stage GAC filtration, 5) chlorination followed by dechlorination, 6) addition of clay based polymer, 7) treatment with peroxide and ultra-violet light, 8) bulk addition of GAC and zeolite powder, 9) treatment with bacteria. This article presents a summary of the test results and of the problems associated with the evaluation of technologies for the treatment of toxicity.

Nov 1, 2002

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By Muhammad Tawalbeh

The calculated temperature history of a single particle of MgCl2 hydrates when it came in contact with fused salt electrolyte at 650 °C was determined using the measured heat transfer coefficient for the molten salt bath at 650 °C. The calculations revealed that the entire interior of the particle reached the temperature required for the formation of MgOHCI from hydrated MgCl2 in less than 2 seconds. This was much less than the time required for dissolution of the prills as observed in experiments. It is very likely that the formation of MgOHCI during prill dehydration and dissolution is a result of hydrolysis in the interior of the prills.

Jan 1, 2004

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By Henri-Louis Jacob

Le Québec dispose de ressources en silice abondantes et diversifiées, pouvant convenir dans l'ensemble à la plupart des usages industriels. Dans les terrains Paléozoïques des BassesTerres du Saint-Laurent et des Appalaches, les ressources identifiées comprennent les grès quartzitiques purs du Croupe de Potsdam (Cambrien), exploités notamment à Saint Canut au nord de Montréal comme source de sable de silice pour l'industrie du verre; les arénites quartzitiques des Formations de Val-Brillant (Silurien moyen) et de Kamouraska (Ordovocien inférieur) exploitées dans l'est du Québec comme source de fondant métallurgique; les grès friables de la Formation de Guigues (Ordovicien) au Témiscamingue, à partir desquels on produit des sables de silice utilisés notamment en fonderie et en filtration. Dans la province structurale du Grenville, au nord du fleuve Saint-Laurent, les métaquartzites purs du Supergroupe de Grenville représentent une source importante de silice pour la production de silicium, de ferro-silicium et de carbure de silicium. Des veines et amas de quartz ont aussi été exploités un peu partout au Québec comme source de fondant métallurgique ou de silice ultra-pure pour la production de silicium métal. Quelques dépôts de sables naturels, généralement d'origine marine ou deltaïque sont finalement exploités dans la région de Montréal comme source de sable pour des usages n'exigeant pas un produit de haute pureté.

Jan 1, 2001