Search Documents

By J. Mirza, E. Nicol, J. Lipkowski

Gold passivation in thiosulfate leaching media is a major barrier to its implementation. Addition of Cu (II) into the leaching solution has shown to aid in gold dissolution, but the mechanism by which it acts, and its role in the passive layer, remains unknown. Surface Enhanced Raman Spectroscopy (SERS), in tandem with linear sweep voltammetry, were employed to determine the dependence of leaching currents on mass transport and for fingerprint identification of sulfur species on the surface of gold. SERS leaching experiments were performed using gold nanorod electrodes that showed increased stability compared to other SERS active surfaces.

Jan 1, 2011

By R. J. Smyth

A Steel Compression Reinforcement Repair Technique (PetroSleevel) system has been developed that has the ability to repair pipeline defects such as stress corrosion cracking (SCC) without requiring welding to the operating pipeline. The Technology has been used to repair active cracking in ERW seam and cracking in the pipe body. All repairs were performed while the pipeline was in operation. This paper will discuss the engineering theory, testing performed to verify the engineering theory, and examples of actual sleeve installations.

Jan 1, 2005

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By L. Zeka, I. Ndala, J. Frenay, S. Gaydardzhiev

"Reductive leaching of cobalt (III) from a heterogenite bearing ore has been performed. Pyrite was added to the system and simultaneously bioleached in order to provide ferrous iron as reducing agent. Within such arrangement the iron ions are continuously re-circulated inside a Fe 3+ / Fe 2+ loop. As a result Co(III) is solubilized in the presence of Fe 2+ ions in concentrations well below the stoichiometric requirement. The ore has been initially subjected to acid pre-leaching in order to guarantee that the available Co (II) has been entirely removed. Two technological parameters have been studied to show influence on the degree of cobalt leaching: concentration of ferric iron in the inoculum and the presence of bacteria. The bacterial role could be mainly viewed in supplying ferric ions in the system which chemically react with the pyrite to generate ferrous ions used as Co(III) reducing agent. Co(III) dissolution has been less efficient when the concentration of total iron in the system was low, but also when microorganisms were absent. SEM observations on leached heterogenite have evidenced bacterial attack on the mineral; however the precise role of bacterial presence on cobalt (III) leaching is still to be elucidated.INTRODUCTIONCobalt accompanies quite often copper in secondary oxidized ore deposits (Rumbu, 2013). In such associations cobalt is found both as CoII+ as well as CoIII+ (Deliens, 1974). In contrast to cobalt (III), cobalt (II) is leached relatively easy in sulphuric acid solutions. Cobalt (III) when present in mineral form belongs to the heterogenite mineral group with a simplified chemical formulae Co2O3.H2O or CoOOH. In order to be brought in solution, heterogenite should capture two electrons, likewise shown in reaction 1 below:"

Jan 1, 2016

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind's eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929

By J. B. Rubenstein

This work demonstrates the feasibility of using confocal surface profilometry to measure and characterize wear of graphite anode surfaces. This method was tested using anode samples that were electrolyzed for 24 hours in a laboratory-scale magnesium cell with a high oxide molten salt electrolyte. The oxide produced accelerated wear on anodes designed for low oxide electrolytes. Contour maps, which are effective at displaying non-uniform wear, and total graphite consumption values were generated from the collected surface coordinates. Along with both qualitative and quantitative analysis capabilities, this measurement system was shown to have a fine resolution and a low detection limit.

Jan 1, 2004

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By Ji Wang

Reflective in-seam wave detection has the advantages of a far detection range and wide applicability. It has been successfully used in detection of many abnormal geological structures in work-faces, such as faults and collapse columns. However, a reflective in-seam wave is a dispersion wave. It has weak energy and is always covered by the direct in-seam wave. In the past, underground seismic explorations were not able to image the opposite roadway using reflective in-seam waves. To solve this problem, we propose a new method of reflective in-seam wave imaging based on adaptive dispersion filtering. This method processes the reflective in-seam wave using a filter with the parameter of transmission distance. The degree of similarity of the filtered and the explosion signal is used to estimate the transmission distance and image the reflective objects. We test and verify this method using real underground seismic data. This research is helpful for the detection of coal mine goafs and abandoned roadways in work-faces or in front of tunneling ends.

Aug 1, 2013

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By H. W. Fleming

In 1955, the results of a regional, geological interpretation of the northern portion of New Brunswick were used as a basis for selecting, for intensive exploration, three areas in which structural and stratigraphic conditions were believed to be favourable. Airborne electromagnetic work, in one of these areas, provided the justification for acquiring the Murray group. Even though the initial results were discouraging, this geological interpretation, combined with the fortuitous discovery of cop• per-bearing float, was sufficient reason for carrying out further work using geochemical methods. This work finally resulted in the discovery of the Murray massive-sulphide deposit, after about eighteen months of coordinated exploration on the property. While this deposit is a typical New Brunswick-type base-metal occurrence, extensive leaching has produced a fossil gossan that rendered it an elusive target for exploration techniques of limited penetration Full credit for localizing the target area is given to the geochemical techniques, but geophysical surveys were needed to provide the necessary

Jan 1, 1961

By I. Ciabatti

Inorganic salts of hexavalent iron (ferrate (VI)) are versatile reagents for water and industrial effluent treatment because of the strong oxidising effect of the ferrate ion (FeO42-) and the well-known coagulation properties of the resulting ferric ion. Among other applications, ferrate can effectively remove arsenic, cyanide and phenols from industrial effluents. Furthermore, ferrate salts can be prepared from ferrous sulphate, a common byproduct of the steel and titanium industries, and possibly from other iron wastes. Notwithstanding their many potential advantages, the industrial-scale application of ferrate salts, such as potassium ferrate (K2FeO4), for effluent treatment has been hindered by the difficulties inherent in their synthesis and stabilisation. Within a project co-funded by the European Commission, the large-scale synthesis of stabilised potassium ferrate was realised through a new synthesis process, and different applications of the resulting ferrate to effluent and wastewater treatment are under investigation. This paper reports the results of the application of stabilised potassium ferrate for the purification of textile effluents. Laboratory and pilot-scale tests were carried out and the performance of the ferrate was compared to that of chemicals currently used in wastewater treatment. According to these experiments, potassium ferrate is a promising reagent for an effective treatment of textile and other industrial effluents.

Jan 1, 2006

By A. Warczok

The mechanisms and kinetics of copper oxidation and reduction have been investigated in small scale thermal gravimetric experiments as well as in laboratory pilot scale, packed bed reactors. With blister copper flowing gravitationally down through a packed bed of ceramic particles, counter-current to low oxygen containing combustion gases, the rate of oxidation was found to be very high due to the large surface area created. Similarly, reduction by flowing copper through a packed bed of charcoal lead to rapid de-oxidation. Based on these laboratory measurements, fundamental rate data have been obtained. Modeling of industrial sized packed bed reactors using the laboratory results, opened up the possibilities of developing a new, very intensive, continuous process for copper fire refining. The developed mathematical model together with a computer process simulator, allowed for the design of the industrial-pilot installation to be built and tested at the ENAMI Paipote smelter in Chile.

Jan 1, 2007

By R. A. L. Drew, F. Jalilian, M. Jahazi

Joining of superalloy Inconel 61 7 with a foil interlayer using transient liquid phase bonding (TLP) technique was studied. Inconel 617 is a solid solution, Ni - Cr - Co- Mo alloy with an exceptional composition of high temperature strength, oxidation, carburization resistance and thermal stability. In this investigation, two bonding temperatures, 1065°C and 1150°C, and two interlayer thicknesses with joining times varying from 5 minutes to 24 hours were employed. Experiments were carried out using nickel base interlayer (A WS BNi-3) with boron as the melting point depressant (MPD) element. Joints were characterized using optical microscopy, SEM, FEG-SEM, EBSD, XRD and microhardness. The results indicated that the rate of elimination of the liquid phase with increasing the bonding temperature, holding time and decreasing the thickness of the interlayer increased. The main precipitates in the diffusion layer had platelike and blocky morphologies for both bonding temperatures and all holding times.

Jan 1, 2006

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Arsenic in mineral processing solutions and effluents is commonly removed and immobilized via iron(III)-arsenatecoprecipitation. The effect of re-crystallization of 2-line ferrihydrite on the long-term stability of iron(III)-arsenate coprecipitate is still not fully understood. This work investigated the redistribution of arsenic and iron during 2-line ferrihydrite transformation at different pHs and temperatures over time. X-ray diffraction (XRD), transmission electron microscopy (TEM) and chemical extraction were employed to characterize the crystallinity of the iron oxyhydroxides. Results showed that the amount of arsenic released into solution during aging increased significantly with increasing media pH.

Jan 1, 2014

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012