Search Documents

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By A. L. MacAllister

"Keymet Mine lies on the Elmtree River 4 miles west of Petit Rocher and about 18 miles northwest of Bathurst, Gloucester County, New Brunswick. A good gravel road runs through the property.The deposit was discovered in 1880 when a vein 7 to 8 feet wide was re-ported. In 1883 the first shaft was sunk as part of an exploration program which was carried out sporadically until 1897, when the company dissolved. Activity on the property was intermittent until 1946 when the property was again staked and during the next year diamond drilling intersected the vein in several places. In December 1949 Coulee Lead and Zinc Mining Company optioned the property and held it until its sale to Keymet Mines Limited in June 1952. By July of the same year work had begun on a three-compartment shaft.Early development work was concentrated on the 150, 300 and 450 foot levels but the shaft has since been sunk to I,228 feet to allow for eight levels at intervals of 150 feet. Little lateral work has been done to date below the 600-foot level.The first mill constructed to treat the ore was to go into production in the spring of 1954, but was destroyed by fire. A second mill, having a capacity of 200 to 300 tons a day, was officially opened October 25th, 1954. Present shipments are zinc and copper-lead-silver concentrates.The rocks of the area are shale, conglomerate, limestone, and quartzite with minor interbedded volcanic rocks, all probably of Silurian age. Small plugs of Devonian acidic intrusions occur 3 miles east and about 5 miles northwest of the mine. Minor dykes of both acidic and basic rocks occur on the mine property. In many of the fine-grained sedimentary rocks the more brittle laminre have been brecciated and give the rock the appearance of an argillaceous conglomerate."

Jan 1, 1949

By D. Monder

Fuel cells are promising sources of electrical energy because of their exceptionally high efficiencies and low environmental emissions. Solid oxide fuel cells (SOFC) are high temperature, ceramic electrolyte cells, which unlike most other fuel cells, can work with a variety of fuels besides pure hydrogen, including hydrocarbons and hydrogen sulfide. In this presentation I present the models we have built for a single H2S fuelled SOFC. The goal is to model the electrochemical reaction coupled with mass transfer, fluid flow and current/voltage distribution in an yttria stabilized zirconia electrolyte fuel cell assembly operated between 750 and 850 °C. Two models of the above SOFC are discussed in this work, 1) an algebraic model derived by integrating a one-dimensional model along the thickness of the cell, and 2) a two-dimensional finite element axi-symmetric model. Important physical and kinetic parameters in the 1-D model are fitted using experimental data sets at three different temperatures and reasonable fits are obtained for the data sets at 800 °C and 850 °C. However, the third data set at 750 °C does not give a good fit using this model. We need to apply the curve-fitting to more data sets to investigate it further. The main conclusion that can be drawn from the present study is that the ohmic resistance of the cell is very high. Contact resistances are believed to be the reason behind this although there could be contributions from resistive interphases. The 2-D model also gives reasonable fits to data sets. One of the publications by the laboratory group doing the experimental work in our department presented very interesting data that shows the cell performance being a strong function of fuel flow-rate. We want to model this behaviour and will have to depend on the 2-D model as the 1-D model does not have flow-rates as parameters.

Jan 1, 2005

By L. A. Melis, K. S. Fraser

"This paper describes the development of a milling circuit for the complex Midwest orebody, containing a high-arsenic uranium ore typical of that found in northern Saskatchewan. The results of preliminary bench-scale test work are summarized. Data from a pilot-plant program carried out at the Ontario Research Foundation are provided for the selected mill flowsheet. Also described are waste circuits which have been established to produce effluents of acceptable quality. Pilot-plant testing of sub-aerial tailings deposition is also described. The applicability of manufacturers' equipment for the various circuits in the flowsheet is discussed.IntroductionThe Midwest uranium deposit is in northern Saskatchewan, 700 km north of Saskatoon, near the eastern edge of the Athabasca BasinDevelopment work on the project is directed by Canada Wide Mines Ltd., a subsidiary of Esso Resources Canada Limited. Participants in the project are Esso Resources Canada Limited, Numac Oil and Gas Ltd., Bow Valley Industries Ltd ., Mink Mining Corporation and Midwest Mining Corporation.The deposit consists of a series of flat lenses of massive ore overlain by a halo of lower-grade sandstone ore. The massive ore is formed of pitchblende and nickel arsenides, along with clay, and averages about 10% U and 9% Ni, The principal minerals are pitchblende (UO2-UO3), coffinite (U(SiO4)1-x(OH)4x), gersdorffite (NiAsS), niccolite (NiAs) and rammelsbergite (NiAs2). The sandstone ore, a friable clay-rich sandstone with sooty pitchblende, averages about 0.4% U and 0.6% Ni. Typical expected mill feed analyses are given in Table I.A bench-scale development program ore was carried out during the period from August 1978 to May 1981 in the laboratories of Lakefield Research of Canada Ltd. (Lakefield), (Lakefield, Ontario), the Colorado School of Mines Research Institute (CSMRI), (Golden, Colorado) and, to a lesser extent, the Ontario Research Foundation (ORF), (Mississauga, Ontario) and the Saskatchewan Research Council (SRC), (Saskatoon, Saskatchewan). Direction of the development studies was shared by Canada Wide Mines Ltd. and its metallurgical consultants, A.H. Ross and Associates. Input was received from Envirotech, Enviroclear, Interox America, and Knight and Piesold Ltd."

Jan 1, 1983

By B. R. Schneiders

"Atikokan is 200 km west of Thunder Bay and earned its mining fame from the discovery of the Steep Rock Iron Range in the late 1930s. Gold, however, was discovered in the Atikokan and Mine Centre areas in the late 1800s and eventually led to one of Ontario's first gold camps, and a total production of approximately 52,000 oz of gold and 174,000 oz of silver from 218,000 tons milled.The general geology of the area consists of Early Precambrian rocks of the Wabigoon and Quetico subprovinces, separated by the east-trending Quetico Fault. The Wabigoon Subprovince, to the north, consists of metavolcanics, minor metasediments and granitic batholiths. The Quetico Subprovince consists of metasediments and granitoids. Small ultramafic plutons occur throughout the metasediments.Within a 50-km radius of Atikokan, more than 50 gold occurrences, prospects and past producers have been discovered since the 18oos. The Atikokan Gold Study performed by the Ontario Geological Sur vey (Wilkinson, 1980, 1982) defined three types of gold mineralization in which gold is concentrated in quartz and quartz-carbonate veins:I) Metavolcanic-Hosted, Stratabound Type-associated with altered felsic fragmental units and chemical sedimentary rocks; possible gold mineralization source rocks. The mineralization is due to metamorphogenic (epigenetic) enrichment. Associated with dynamic metamorphism events and/or felsic intrusive events.2) Marmion Lake Batholith Type-occurs within the gneissic core of the batholith associated with north east-trending lineaments, representing faults or shear zones. Mineralized veins are related to several periods of deformation and shearing, suggesting that metamorphogenic veins were produced during dynamic metamorphism.3) Contact Zone Type -occurs in the contact zone rocks between gneissic batholiths and meta volcanic belts. Hydrothermal solutions produced during several deformational periods acted to leach and concentrate gold mineralization. Localized, discontinuous shear zones host the epigenetic (metamorphogenic) veins.Twenty-one properties in the area were mapped and sampled, and researched petrographically and geochemically. Geological data from the Atikokan Economic Geologist Program of the Ontario Geological Survey are used in discussing the types of mineralization, genetic models, and exploration targets and techiques."

Jan 1, 1983

By w. w. Milde

"Since its startup in 1975, the Rabbit Lake mill has been modified (0 process both increased tonnage and higher grade ore. Ore initially came from the Rabbit Lake pit . In 1985, a major mill expansion was commissioned to allow treatment of B-zone pit ore, which is mineralogically and metallurgically different fromRabbit Lake pit ore.Mill modifications, and the changing ore characteristics and processing targets which made them necessary, are described. Mill LocationThe mill complex, shown in Figure I, comprised of milling facilities, acid plant, power generation , warehouse and administration offices, is located approximately 1.5 Ian south of the Rabbit Lake pit, and about 8 Ian southwest of the B-zone open pit mine.Original Milling CircuitOre feed to the mill commenced June 10, 1975. The mill was designed to process 1500 tonnes per day , 483 000 tonnes per year with an average grade of O.44OJo Ups and an annual production of 2000 tonnes UPs' Run-of-mine ore was dumped directly onto a 60 em square opening grizzly. Oversize was broken with an Ingersoll-Rand hydrauli c rock breaker. Minus 60 cm ore was fed to a 6 m diameter by 1.8 m long Hardinge semi-autogenous (SAG) grate discharge mill. Mill discharge was screened over a Tyler double-deck vibrating screen, with screen oversize returned to the SAG mill feed chute via conveyor belt. Screen undersize (minus 2.4 mm) was pumped to 51 cm diameter Krebs cyclones in closed circuit with the SAG mill. Cyclone overflow (about 50% minus 74 micron) was thickened to 55% solids in a 30 m diameter neutral thickener .Thickened pulp was stored in two mechanically-agitated wood stave tanks (5.5 m diameter by 6 m high), to which sulphuric acid was added to obtain a pH range of 1.5 to 2.0. The fmalleaching was carried out in five more identical tanks. Sulphuric acid and sodium chlorate were used to maintain a pH of 1.5 and a terminal emf of -450 to -500 mV. Steam sparge was utilized to obtain a temperature of 45°C."

Jan 1, 1989

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By P. O. Rag, Daniel E. Walsh

"Gravity concentrators are evaluated either in closed or open circuit. The process developed by MIRL employs the use of neutron activated gold (/98Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. In addition to allowing for a more accurate and detailed recovery analysis, this process significantly reduces the time and cost required for unit evaluation when compared to other gold recovery analysis procedures. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems.IntroductionThe surge in gold prices of the late 1970s and early 1980s was followed closely by a renewed interest in gravity concentration processes, especially in concentrators claiming efficient recovery of fine placer gold. Cones, spirals, spinning bowls, jigs and cyclones are all considered potential fine gold concentrators. Fine gold, in this context, is defined as not only that gold finer than 250 um (60 mesh""), but also coarser gold, whose low shape factor may decrease its recovery by conventional, large-scale sluicing operations.Adoption of fine gold concentrators by the Alaskan placer milling industry was retarded by the lack of reliable, accurate, and reproducible data on concentrator efficiency with respect to fine placer gold recovery. In most cases, concentrator performance was based on a limited number of tests run on placer material, about which only slight knowledge of gold size and shape characteristics existed. In order to be prepared for the resurgence of interest in fine gold concentrators, which will follow the next upturn in gold prices, a detailed study of the fine gold recovery characteristics of gravity concentrators needs to be conducted."

Jan 1, 1986

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982

By Michel Dagbert

"This paper illustrates the different ways grade-tonnage curves can be generated f or a mineral deposit. It emphasizes systematic discrepancies between reality, estimates and actual production according to different estimation methods and grade control programs. It does not offer a universal solution to the prediction of grade-tonnage curves. Hopefully, it will inspire caution to mineral economists who use estimated grade and tonnage data in the establishment of an optimum cut-off grade for a mining operation.IntroductionThe value of a mineral development venture often depends on a grade-tonnage curve. Statistics can help. The idea is to divide mentally the orebody into small blocks called selective mining units or SMUs. A SMU is an idealized version of the quantity of rock the grade of which will be tested against the cut-off at the time of mining. It could be as small as a truck load or a shovel load in very selective operations like some uranium mines where radiometric probing of each truck or car is performed. More typically, in an open pit operation, it will be the smallest zone flagged as ore from blast hole data, e.g. a 5 m by 5 m by 10m block, if blast holes are on a 5 m grid and bench height is 10m. Having defined the SMUs, the grade-tonnage curve determination amounts to evaluating the grade distribution of all the SMUs that can be mined in the depo sit. If we know this distribution we simply apply the cut-off to it and we get the number of SMUs above the cut-off (i.e. ore tonnage) and their average grade. .Assessment of the grade distribution of SMUs from exploration drill hole data is not an easy exercise and much has been published on the subject (David, 1972; Marechal , 1972; Huijbregts, 1975; Marechal, 1975; Guibal and Touffait, 1982). In this paper, we use a gold mine example to illustrate the influence of SMU size on the results. With the same example we also show that ""common-sense"" methods of grade-tonnage curve determination can sometimes be misleading."

Jan 1, 1987

By D. Crone, T. Watts

"The Lindsley project was a program of deep drilling to test the contact down-dip from two nickel-copper deposits, one uneconomical and the other mined out. The role of Borehole Pulse EM(PEM) was to detect the higher grade, more massive sulphide zones if they were missed by a drillhole, and to help determine geometry if the zones were intersected. Two problems appeared as the PEM survey progressed: (1) conductivity-thickness as measured by the PEM did not always relate to economic sulphides as determined by the market; (2) a pattern of unusual PEM anomalies was obtained that indicated something odd and big, but the cause was unknown. A large fold structure subsequently was indicated by a program of deepening previous holes, the third of which intersected high-grade mineralization below 1280 m. Falconbridge is in the process of shaft sinking and underground exploration.IntroductionThe Falconbridge Lindsley property is on the south rim of the Sudbury basin, 8 Ian north of downtown Sudbury. The original property was acquired by a prospector named James Stobie, who, in early August 1885, staked a showing that later became the Mount Nickel mine (Fig. I). On August 10 Stobie staked another property that would become the Little Stobie mine, and at the end of the same month he staked the main Stobie orebody.In 1888, the ground immediately west of the MOlU1t Nickel find was staked. This ground contained the Blezard deposit (Fig. 1) which was put into production in 1889 and was eventually acquired by Inco. Down-dip from the Blezard workings, on Falconbridge ground, is located the upper Lindsley No. 1 deposit which was drilled off by Falconbridge in the 1940s to 1950s. A decision to go underground on the Lindsley No.1 mineralization was made in 1969, but the project was cancelled in 1971 because of declining nickel prices. The shaft was stopped at 95 m, and the headframe and hoist were sold. Further surface exploration drilling in the 1970s discovered the deeper Lindsley No. 2 zone, but as it had grades similar to those of the No. 1 zone, it too was considered uneconomic."

Jan 1, 1992

By E. Goodwin

"Maclaren Forest Products Inc.Lime is commonly used for the neutralization of acid, and the removal of heavy metals in mine waste waters. However, the precipitation of heavy metals as hydroxides must take place under conditions of controlled pH, to produce minimum concentrations of dissolved metals. An account is presented explaining the concepts applied to lime-treatment processes at Bell Mine during the period of a supernatant discharge to Babine Lake; October 18, 1982to January 25, 1983. IntroductionBell Mine of Maclaren Forest Products Inc., Babine Mining Division, an open-pit copper mine, is located on Newman Peninsula, Babine Lake approximately 65 kilometres northeast of the town of Smithers, British Columbia (Fig. 1).A depressed market for copper metal in 1982 forced a management decision to suspend operations at the mine for an indefinite period from October 3 I, 1982. For some time prior to the mine closing date, mine management was concerned about the increasing level of supernatant in the tailings pond , and its possible effects on the stability of the dam when cycloning of mill tailings ceased. Consideration of these potential hazards led to an application being filed with the Provincial Waste Management for a permit to discharge the excess water to Babine Lake. This large lake, an important link with several significant salmon spawning sites, is a major contributor to the British Columbia commercial fishing industry. Jurisdiction for the environmental affairs in the area is shared by the Department of Fisheries and Oceans, the Environmental Protection Service, and the Provincial Waste Management Branch. These agencies were directly concerned in the formulation of discharge permit following joint consultation, and exchange of information with the company on environmental concerns. An approval was finally granted to discharge approximately 1,000,000 cubic metres of supernatant from the tailings impoundment at Bell Mine into Hagan Arm, Babine Lake from October 18, 1982 with a daily discharge not to exceed 9000 cubic metres. Provisions were made that a particular discharge procedure be followed, and that the company would be responsible for setting up a sampling and monitoring program to safeguard the quality of the effluent."

Jan 1, 1986

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By I. Clauzier

"A new method of managing electricity to reduce costs andimprove profits is discussed. Before taking steps to better manage electricity, it is essential to understand the terms peak demand and energy and their effect on an electrical bill. Knowing how electricity is presently used in the plant is the important first step. This goes beyond knowing how much electricity is used at each time of day, the individual contribution of every plant process to the total plant load must be known. At this point, each process is ranked according to importance to production in order to identify possible savings opportunities. These improvements can then be implemented by simply improving operations or in some cases, through the use of an automatic control system. IntroductionIn today's competitive environment, controlling costs is becoming increasingly important. All costs associated with operation must be controlled in an effort to improve competitive position. Electricity is a cost component that can and should be managed.Although the term management can mean different things to different people, the intent is always the same: to make the best possible use of existing resources, whether labour, equipment or electricity.The simple approach to managing electricity presented in this paper consists of four steps.I. Understand Peak Demand and Energy. It is essential to understand the terms, peak demand and energy and their effect on your electrical bill.2. Know Your Present Electrical Use. The present use of electricity in the plant must be known. This goes beyond simply knowing how much is used at each time of day, to accurately knowing how each process is contributing to the total plant electrical load, and ultimately to the electrical bill.3. Identification of Savings Opportunities. With this information, energy savings opportunities for reducing the electrical bill and improving profits can be identified.4. Implementing Improvements. Having identified areas of potential savings, improvements can then be implemented in order of their significance. This could be a matter of simply improving operations, or in some eases may mean the use of an automatic control system.These four steps can result in significant dollar savings."

Jan 1, 1987

By Charles A. Schacht

"Relining, lining maintenance, and ladle repair can represent a significant cost in steelmaking. Therefore, the objective of all steelmaking shops is to minimize this cost and to maximize the lining life. However, the thermomechanical behaviour of the ladle lining is highly complicated and sometimes misunderstood. The ladle design also has a significant influence on lining life. Other factors which have a direct influence on lining life are the shop lining installation practices and manner in which the ladle is used. The objective of this paper is to provide an understanding of the impact of these factors as related to improving the integrity of the lining and increasing lining life.Fundamentals of Steelmaking Ladle Lining Expansion ForcesNumerous studies have been conducted by the author on steelmaking ladles with molten metal capacities ranging from 110 ton s to 350 tons. The steelmaking ladle typically has a sidewall plate with a slight taper and for analytical purposes can be classified as a cylindrical vessel.A typical ladle is described in Figure I. The ladle sidewall lining usually consists of a working lining and a safety lining. Although the type of refractory used in the working lining varies based on the type of steel produced and other metallurgical requirements, the refractories typically used are: 70% alumina brick; direct bond mag-chrome brick; resin bond dolomite brick; and direct bond dolomite brick. Fireclay brick, high alumina brick, or a similar strength brick is used as the safety lining.Normally, the ladle lining is exposed to a through-thickness temperature gradient and restrained by the ladle sidewall plate, is described in Figure 2. The hot face side of the refractory lining develops a compressive thermal force and the ladle sidewall plate develops an equilibrating tensile force. The radial joints open on the cold side of the working lining as the lining joints have little or no tensile strength. A radial compressive load (P) develops between the working lining and the vessel shell due to the thermal restraint imposed on the lining by the shell. The radial compressive load is transferred from the working lining through the safety lining onto the ladle sidewall. Therefore, the safety lining must have the strength to accommodate the radial compressive load (P)."

Jan 1, 1991

By P. G. Keohane, J. S. Drake

"Cominco's Polaris Mine is a lead-zinc underground operation that began commercial production in early 1982. The mine site is located on Little Cornwallis Island in the Canadian Arctic at a latitude of 75°23'N and at a longitude of 96°55'W. The nearest settlement, Resolute Bay, some 100 kilometres southeasterly from the mine, is accessed from the mine by light aircraft. The mine site can be accessed by sea during the six-week ice-free period each year. During this time all major operating supplies are brought to the mine and the lead and zinc concentrate products are shipped out to market.GeologyThe Polaris orebody lies near the top of the Thumb Mountain Formation of Ordovician age. This formation is a relatively homogeneous section of thin to medium bedded limestones which are brecciated and dolomitized in the area around the orebody. The deposit is described as a Mississippi Valley-type orebody. Ore minerals are sphalerite and galena with the waste being predominantly dolomite with calcite and marcasite. The ore is quite porous with voids being generally filled with ice as the mineralized zone lies entirely within permafrost. Reserves consist of about twenty million tonnes of ore grading 3.8% Pb and 14.3% Zn with a further three million tonnes of inferred ore at a slightly lower grade.The orebody strikes in a north-south direction with the hangingwall dipping at about twenty degrees to the east. It is generally conformable with the stratigraphy. The footwall in the western portion of the orebody, the Panhandle, lies about 10 to 30 metres below the hangingwall. To the east the footwall drops sharply, creating an orebody height of up to 110 metres in what is referred to as the Keel Zone. The Panhandle Zone has typically 80 - 110 metres of cover above the hangingwall , About 25% of the reserves are in the Panhandle Zone, the remainder being in the Keel Zone. Figure I illustrates a plan view of the orebody relative to other surface facilities on the property and Figure 2 illustrates a simplified section through the Panhandle and Keel Zones."

Jan 1, 1985

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016