Search Documents

By Simon Hanner

November 2005 Memorial University Newfoundland and Labrador Mines and Energy Review of Activities Exploration and Mining New Brunswick ?Université du Québec a Montréal McGill University 2005 Manitoba Mining and Minerals Convention Université Laval Quebec Exploration 2005 Saskatchewan Open House December 2005 University of Calgary University of Alberta 'Laurentian University 'Queen's University 'University of Toronto 'Ontario Prospectors Association January 2006 Mineral Exploration Roundup, BC March 2006 Prospectors and Developers Association of Canada Convention April 2006 University of Ottawa Carleton University

May 1, 2006

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

By Robert B. Parsons

"The annual onslaught of provincial budgets and tax changes is complete, and once again the Canadian taxpayer is being asked to dig deeper into his pocket to fund old and new programs. It is noteworthy that 1987 tax reform promised lower taxes, but a broader fax base. Five years later, we still have the broader tax base, but the lower faxes have gradually crept up to pre-tax reform levels. Surprise! Surprise!IntroductionThe last edition of Tax Notes commented on some important proposals announced in Manitoba's 1992 budget. In this issue, Tax Notes summarizes the 1992 budget proposals of British Columbia, Ontario and Quebec. These budgets reflect the continuing trend of transferring responsibilities and the related costs-from the federal government to the provinces. As well, the budget papers bear witness to the respective governments' political stripes. British Columbia, Ontario and Quebec are seeking higher tax revenues. Only Quebec continues to acknowledge the importance of the mining industry in its annual budget documents."

Jan 1, 1992

By L. Cáceres, G. Leinenweber, P. Bustamante

"Given the severe scarcity of fresh water sources in Northern Chile the use of seawater has become the only alternative to allow mining expansion. This option however poses several technological challenges as a result of the high concentration of natural salts that promote various forms of metal corrosion. Therefore the steel piping protection has been a constant challenge for design engineers responsible for solving the problems of corrosion. Known protection alternatives are varied and expensive, a few of them are rubber coatings, protection based centrifuged concrete, extra wall thickness of pipes in combination with corrosion inhibitors, extra wall thickness of pipes without using corrosion inhibitors, and the use of highly corrosion resistant steel materials.In this framework the aim was to study the corrosion kinetics of carbon steel pipe API 5L X70 under electrochemical and weight loss testing. The test conditions include a range of seawater velocities between 0.2 to 3.0 m/s.For electrochemical experiments the API 5L X70 steel specimen was a 4 mm diameter disk embedded in an 8 mm diameter Teflon rod and exposed to seawater. Duplicated coupons were placed in a standard test apparatus that was built according to the standard ASTM D 2688 – 94.The main results were: a) corrosion mechanism explained in terms of the counterparts partial processes which are the hydrogen evolution and oxygen reduction reaction; b) for the test specimen a corrosion band like feature that suggest a lateral dispersion of aggressive solutions from corrosion pits; c) a range of corrosion rates between 1 and 1.96 mm/year for flow rates between 0.2 and 3.0 m/s; and d) a convenient inhibitor dose between 20–25 mg/L for optimum inhibition efficiency to obtain a maximum value of 80% for corrosion efficiency."

Jan 1, 2016

By H. C. M. Gordon

MR. A. D. BADOUX: I have listened to Mr. Gordon's excellent paper with great interest, as I personally have gone through some of the experi­ences he has so clearly depicted. In particular, there were a good many times when we were greatly exercised in our minds as to whether we were justified or not in closing-off certain sections in the Allan mine. The difficulty in these cases arose from the fact that a peculiar smell could be detected in these sections but at the same ti me there was no positive evidence of spontaneous combustion either from heat being apparent or from the possible indications of fire getting any worse. It was suspected that the small percentage of -carbon monoxide that could be obtained by analysis in the air in these sections, and also the peculiar odour, were emanating from the coal itself, and, in order to verify this, bore-holes were drilled in the coal and the gases released from these bore-holes were analyzed. They were found to contain carbon monoxide. After quite a considerable length of time this contained carbon monoxide gradually diminished and finally could not be detected when analyzing such samples of gas. It was our intention to follow this matter up further, as such an occurrence of carbon monoxide is practically unknown, but the sections in which these occurrences were found had to be abandoned. Mr. Gordon referred t0 a case of spontaneous combustion in the Allan . mine, and I may say that, although the section in which that occurrence took place was travelled and carefully examined every day by the colliery officials, yet nothing unusual was noticed until the fire actually took place. This tire was the cause of a slight explosion.

Jan 1, 1938

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers' special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers' position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By J. P. Aiello

"INTRODUCTIONWhile this paper deals specifically with potential coal use at the Cold Lake Project of Esso Resources Canada Limited, a majority of the technical aspects of coal conversion could apply to any oil field and industrial boilers or stearn generators. In 1962, Imperial Oil Limited's production arm (the forerunner of Esso Resources), began examining methods of extracting bitumen from a 50 m thick layer of oil sand buried 450 m below the surface in the Cold Lake area. Almost two decades of research followed to develop an in situ oil sands recovery technology that made commercial production feasible.A $13 billion mega project that would have produced 22 000 m3/d (141 000 barrels/day) of synthetic crude oil (160 000 bpd of bitumen) was shelved in 1981, and ultimately replaced by a phased development strategy, involving smaller production units, to bring blended bitumen production on stream as markets and prices permit.The first two phases came into production in 1985. There are currently a total of six phases in production with four more in the construction stage. Each phase has 130to 140production wells (initially) and a central plant with water treatment, crude treatment and stearn generating facilities capable of producing 150 m3/d (9500 bpd of raw bitumen). The stearn generation section for each phase consists of three 180millionBtulhour oil fieldsteam generators.In its natural state, the bitumen is too thick to be recovered using conventional oil recovery techniques. At the Cold Lake Project, bitumen is recovered by a method called cyclic stearn stimulation. Water is pumped to the central plant where it is treated and heated to produce high pressure, high temperature steam. During the steam cycle, this steam is transported in insulated pipelines to the wells for injection into the oil sand formation. This cycle lasts from 30 to 50 days, heating the formation and causing the bitumen to flow. Following an initial flowback period, a surface based artificial lift system pumps the heated liquid bitumen, mixed with water and gas, out of the well and back to the central plant. The water and gas are separated from the bitumen, with the gas being used to provide some of the fuel for the stearn generators and the water being treated and recycled. Approximately 5% of the water cannot be recycled and is disposed of by injection into deep formations . The bitumen is blended with a diluent and shipped by pipeline to market."

Jan 1, 1989

By W. Andrew Falls

Although we have yet to reach the midway point in the decade, the copper concentrate market has already witnessed some of the most volatile swings in history, moving from record high treatment and refining charges in 1991-92 to historic lows, in real terms, during the past year. What has been the cause for such volatility? By and large the swings can be attributed to factors of supply and demand in the "custom" copper concentrate market. For example, two relatively recent events which had a major impact on the supply-demand balance were the shutdown of the Bougainville copper mine in Papua New Guinea in 1989 due to rebel insurgency and the startup of the La Escondida mine in Chile in 1992. The first event, threw a balanced to slightly surplus concentrate market into a substantial deficit, forcing treatment terms down as smelters, caught short by the loss of concentrate supplies scrambled to cover their positions. The second event, brought over 300,000 mt per year of new copper in concentrate to the market, more than reversing the losses from the Bougainville shutdown. In combination with other additions to mine capacity via new mines or expansions, the custom concentrate market moved into a huge oversupply in 1991-92 and many mines found themselves unable to place uncommitted tonnage. But even this event was quickly overcome by the use of underutilized capacity at non-traditional buyers, such as those in the C.I.S., Zambia, or those which were not traditionally buyers of custom materials. All of this has happened in the space of five short years, a mere snapshot in the history of the market. I'll return to these points a little further on, but first I would like to review the fundamentals which govern the copper concentrate market.

Jan 1, 1995

By Garth A. Maki, Douglas M. Smith

"The largest Canadian Lamella thickener installation to date, with 13,600 square feet of effective clarification area, is being successfully operated at the Rocanville Division of the Potash Corporation of Saskatchewan. This paper describes the operational principles and design features of the Lamella thickener, the testwork leading to its specification f or the Rocanville phase two expansion project and a review of the performance of the full- size unit which was ultimately installed.IntroductionThickening equipment operating in the Saskatchewan potash industry is generally situated within the main refinery building or a separate insulated an d he a ted structure due to the harsh winter climate and the need to closely control plant brine temperatures to en sure good flotation circuit performance Because these thickeners process large volumes of slurries, conventional basin-type designs tend to be large, ranging up to 46 metres in diameter or more. As part of the general effort to minimize capital costs, the potash industry has begun investigating the use of alternate high capacity, compact thickener designs. In this regard, PCS Rocanville undertook a program in 1978 to evaluate a LamellaTM thickener and one other type of ‘High Rate' thickener as alternatives to a conventional design for the phase two expansion project.This paper describes the operational principles and design features o f the Lamella thickener (manufactured by Axel Johnson lnc.), the testwork leading to the specification of a Lamella for the Rocanville expansion project and are view of the performance of the full size unit (1486 m2 of the effective settling area) which was ultimately installed and is now successfully operating in the Rocanville plant."

Jan 1, 1983

By P. Cielo

"Nondestructive inspection is an important quality control tool in the material processing industry. Being nondestructive, such a control may be applied to the whole production, as long as the available techniques are fast and easily automated. Ideally, nondestructive testing (NDT) methods should operate in a noncontact configuration in order to be deployable on-line with minimum perturbation of the production process.After a short introduction to the most common NDT techniques, with particular emphasis on ultrasonic, radiographic and electromagnetic methods, a few new approaches which are under development at the Industrial Materials Research Institute, (Boucherville, Quebec), are reviewed. Noncontact techniques such as laser ultrasound, thermoelastic and thermographic methodologies will be described, and their applications to materials of industrial interest will be discussed."

Jan 1, 1989

By W. B. Morrey

"In recent years, the major effort in detonator development has been concentrated on ""non-electric"" systems. Existing types all involve some form of explosive reaction to transfer ignition energy from outside the borehole to the pyrotechnic delay element contained within the detonator. These may be based on low-energy detonating cords having grained or plasticized explosive cores, shock tube energy transmission principals and explosive gas ignition systems. Each has properties of internal and external effects not present in electric conductors.The MAGNADET System introduces transformer coupling into electric blasting circuits. Safety features with respect to current leakage, stray currents of AC or DC source, electrostatic energy and radio-frequency radiation are comparable to ""non-electric"" systems, with advantages in simplicity, speed of hook-up and range of application.The transformer device used is a small ferrite ring or toroid which is an integral part of each specialized detonator. The detonator legwires form the secondary side of the transformer winding. The primary side is a single wire loop common to all units within the circuit. Power is supplied from a frequency-tuned portable exploder with unique circuit-sensing features.The MAGNADET System is expected to have particular application to shaft sinking, raising and tunnelling where the protective features as well as speed and efficiency are critical factors. Applications of the 'MAGNA' booster in quarries, open pits and longhole deck charges offer control over vibration problems and elimination of surface noise.IntroductionFor many years, electric detonators and electric blasting systems dominated surface and underground applications where controlled delay times were required. Control over the instant of detonation by blasting machines or power-line switches is the major safety feature.Electrical energy exists in many forms. It may originate from many sources. Electrical energy can be difficult to contain. It may enter or escape through a variety of conductive paths. It may fluctuate, concentrate or dissipate to pose a most elusive potential hazard."

Jan 1, 1982

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By Roger Moss

OUTLINE Area selection Mineralization/Alteration Styles Island Copper Mineralization Geophysics Geochemistry Coppercorp Setting Mineralization Geophysics Geochemistry Formation Common Characteristics Conclusions

Apr 1, 2005

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

By Marke Wong

? Vietnam?s economy is growing so fast that gross domestic product (GDP) growth remained above 8% in 2005 and exports are rising steadily at 25% per year. ? Demand for electricity is expected to increase 18% per year through 2010 requiring an additional estimated 7,547 MW before 2010 ? Domestic coal demand is expected to be over 45 Mt by 2010. ? The Quang Ninhcoal deposits are estimated at 6.5-7 billion tons (350m) Vietnam News Agency. Saturday, May, 6, 2006. ? National resources are now estimated at 10 billion tonnes; not including a relative new coal bed discovery estimated at 210 billion tonnesin the Red River Basin.

May 1, 2006

By Lorne Roberts

"This paper describes: how Falconbridge's fire protection system meets the needs of the Lockerby Mine; why the system was chosen over other alternatives; how it is unique, but can be applied to any underground situation; details of the system; how it was installed; the role of a fire protection company; and general considerations when choosing afire-suppresant system.IntroductionIn May 1981, after about three years of searching for the best fire protection system for the re-opened Lockerby nickel mine at Whitefish, near Sudbury, Ontario, Falconbridge Nickel Mines Ltd. installed an AFFF type of fire suppression system. It was designed and supplied by the Fire Protection Systems Division of Levitt -Safety Ltd.The system protects against loss of life, equipment and/or production, and it complies with legislation should fire occur in a fuel storage area and/or scooptram garage and service bay at any or all of the three levels near Shaft No.2.About 18 months after Levitt-Safety began working with Falconbridge, the system was designed and installed at a cost considerably less than that which would be incurred if fire damage caused the loss of two days of production.The fire protection system, which overcomes a limited water supply, is a self-contained balanced pressure proportioning system. It senses the flow and automatically determines the correct concentration of foam to water. It is triggered by a release mechanism which operates a bank of nitrogen cylinders, which in turn pressurize a pressure vessel to expel the foam concentrate and water from the tanks. This solution is piped to sprinkler heads in the specific area."

Jan 1, 1982

By R. Pakalnis, D. Tenney, B. Lang

"This paper describes three case histories whereby numerical methods were employed as a tool in the identification of potential instability. Simple two dimensional (PCBEM) and pseudo three-dimensional (BESOL, MINTAB) codes were employed to identify zones of induced stress which were subsequently related to extensometer, stress meter and observational data as the stope was excavated. The following case histories will be discussed. MacLellan Mine - sill pillar stability; Ruttan Mine-Hanging Wall Stability; and Detour Lake Mine-narrow vein mining.The MacLellan case history showed how modelling and instrumentation enabled mining to be conducted safely and under controlled conditions. MINTAB and PCBEM were employed to predict sill pillar failure. The sill pillar failure was associated, with an unloading of stress which was recorded by instrumentation (stress meter) and a decrease in the over-all rock mass strength. The yielded pillar, however, maintained its over-all configuration enabling access through the pillar.The Ruttan case history is an example of hangingwall and footwall design whereby the existence of adverse structure coupled with a zone of relaxation results in dilution. BESOL and PCBEM were employed to model a test stope and to verify the observations and measurements through instrumentation . Empirical methods of dilution estimates are employed to determine the level of walls lough with respect to the rock mass rating, stope dimensions and rate of excavation.The Detour Lake case history in an example of open stoping a narrow steeply dipping deposit. Stope dimensions are 135m in strike length, 47 m in vertical height with an average width (F/W to H/W) of3.6 m. Stress meters coupled with visual observations are related to modelled estimates of stress and dilution."

Jan 1, 1991

By E. Contestabile, T. R. Craig

"This report describes the development and effective use of shaped charges as part of the Elliot Lake Mine Roof Stability Project to remotely remove the heads from roof bolts. With a slight modification, these same shaped charges are being recommended f or use to the Brunswick Mining and Smelting Corporation Limited (Mining Division), to cut steel cable bolts.IntroductionThe Canadian Explosives Research Laboratory (CERL) often receives requests to cooperate in solving problems encountered in private industry or other sectors of the government. CERL is equipped to design and test explosive and pyrotechnic devices and the policy is to treat each case individually.The first case reported evolved from a request from a sister laboratory at Elliot Lake. The intent was to remotely remove the head s of roof bolts as part of a mine roof stability project. The device designed for this use was 1000,70 effective in the laboratory and 80% effective in the mine.The second case reported results from a request from a private mining company knowledgeable of the Elliot Lake Project. Their requirement was to remotely cut cable bolts. This request was first treated as presenting a new problem. The solution, however, proved to be very similar to the former."

Jan 1, 1985

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989