Search Documents

By M. Hardy

"The structural design of mine headframes is challenging due to the significant differences in the geometry, rigidity, and behaviour of these structures compared to conventional buildings. The differences are related to the main purpose of these structures, which is not human occupancy, but rather the support of hoisting equipment. The main objective of this paper is to present the seismic elastic behaviour of headframe structures in comparison with conventional buildings, which is the base case for the definition of seismic loads. This paper highlights the impact of backlegs on the dynamic behaviour of mine headframes, more specifically the resulting torsional sensitivity. INTRODUCTION The design of industrial structures is often governed by industrial processes rather than by architectural constraints. In ground-mounted hoisting plants, the structural configuration of headframes must allow clearances around conveyances and ropes while resisting the lateral loads associated with the hoisting equipment. Typically, these structures use backlegs to withstand the lateral loads, which leads to highly irregular structures with unconventional dynamic behaviour. The codes and standards applicable to the structural design of mine headframes in Canada are often incomplete or not adapted to the reality of practising engineers. This situation creates confusion, and engineers must look at various guidelines and international standards to support the engineering calculations required for the design of these structures. The loads resulting from the support of hoisting equipment, such as ropes and conveyances, are usually simple to calculate and are determined based on the information from manufacturer and industry related guidelines. Moreover, the loads associated with snow accumulation and wind are calculated applying the same methodology used for conventional buildings, without any major issues. On the other hand, the seismic loads are often difficult to calculate based on the methodology from the National Building Code of Canada due to the significant differences in the dynamic behaviour of the structures. The resulting structures may be either over-designed or worse, under-designed. Hence, there is a lack of uniformity in engineers’ designs. The latest edition of CSA S16-14 “Design of steel structures” includes Annex M (Informative) “Seismic design of industrial steel structures” to help designers close the gap between the requirements of traditional regulations and actual engineering practice."

Jan 1, 2019

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986

By J. G. Phillips

Introduction Throughout the Great Plains region (the provinces of Manitoba, Saskatchewan, and Alberta), numerous clay deposits of widely varying composition and character are to be found. These may be classified into two general types: (1) surface clays, and (2) shales. The surface clays consist of a heterogeneous mantle of silts and clays interspersed with grave! and sand deposits, and may belong to any of the following groups: (1) lake clays: (2) river-terrace or flood-plain deposits; (3) delta deposits . In most cases, the water from which these deposits were ' laid down was derived from the melting ice of the continental glaciers. These surface clays, in general, possess certain characteristics in common, being all more or less calcareous, often silty, and showing a tendency to 'check' in air-drying. The shales found in this region are of Cretaceous and Tertiary age. These deposits have a wide extent, but there is frequently such a heavy covering of drift material that the clays are accessible chiefly along the walls of stream valleys, or along the escarpments of uplands.

Jan 1, 1929

By R. T. McAndrew

Introduction Drinnan is situated in the Prairie Creek coal area in the Foothills belt of Alberta. It lies on the main line of the Canadian National railway from Edmonton to Jasper. The exact location is shown on the map (Figure I). Interest in the field was aroused by several circumstances: Its proximity to Brule and Pocahontas on the southwest and to Coal-spur on the southeast led to the belief that coal might be economically produced here. There was already at Hinton a 3 ft. 9 in. coal seam being mined by Seabolt. The coal was of very good grade, being black and shiny in appearance with well defined cleavage and a heat value of 12,000 B. t.u. Outcrops of coal had also been noticed on the north side of the Athabaska river and Fish creek. These facts led the Jasper Coal Company to investigate the field. This Company considered taking over the Seabolt property at Hinton, but, owing to the size of the seam, this plan was abandoned and prospecting by diamond drills and test pits was started two years ago in the district east of Hinton. After prospecting had been completed, the most favourable district was found to be in township 51, ranges 24 and 25, west of the 5th meridian. The Company's lease includes all or parts of sections 18, 19, 20, and 28 in range 24, and sections 10, 11, 12, 13, and 14 in range 25. The approximate boundaries of the property are the Canadian National railway on the north, Happy creek on the west, and Cache Percotte creek on the east. The lease comprises 3,100 acres, and the total amount of coal in sight is estimated at 100,000,000 tons.

Jan 1, 1931

By L. O. Thomas

THE Alaska Highway, in its course through British Columbia, traverses parts of two great physiographic divisions of Canada which are also distinctive geologically-the Cordillera in the western section and the Interior Plains in the eastern. The Cordilleran region in the portion of the Province with which this paper deals can be divided into four major northwest systems, known respectively from west to east as Coastal, Plateau, Cassiar-Omineca, and Rocky Mountains. The Coastal system consists solely of the Coast range except in the extreme northwest, where a part of the St. Elias range is included. The Coast range, characterized by mountains of great ruggedness,. is made up of an igneous complex of granitic rocks intruded chiefly as a great batholith. In places, spurs of these rocks extend into the Plateau heft, a partly mountainous tract largely occupied by quartzites, quartzose mica schists and their gneissic phases, and crystalline limestone with interbands and broad areas of chlorite, _hornblende, and sericite schists and bodies of intrusive granite gneiss-an assemblage of rocks known as the Yukon group. The Cassiar-Omineca system marks the divide between the Pacific and Arctic drainages. Its eastern boundary is well defined in the south by the Rocky Mountain Trench (see p. 229). The rocks of the system are, miainly, highly altered Palaeozoic sediments, but there are also Precambrian and Mesozoic rocks, the latter largely volcanic. The core of the system is granitic and there is evidence (see p. 221) to support the belief that it is of such a length as to constitute a batholith comparable to that of the Coastal system.

Jan 1, 1944

By C. E. Dowker

"IntroductionMechanization underground at the Buffalo Ankerite mine in Deloro township, Porcupine district, had reached a high level by 1944, both in equipment available, and in the use of this equipment, for all stoping operations. Power feed leyners and the latest type of stopers for drilling, slushers for moving ore and fill, and tugger hoists for all servicing, did much to halt rising stope costs, and in some cases decreased them. On the other hand, little beyond the use of mucking machines and power feed leyners had been adopted in the effort to reduce level development costs, or to increase the advance per man-shift.Faced with ever increasing level development costs, caused by rising prices of equipment and supplies, coupled with increasing wage demands for less physical effort, it was realized that more mechanization of development work was essential. The objectives of such further mechanization were:(1) Decreased development costs(2) Increased footage per man-shift(3) Less physical effort by development crews, with greater take-home pay (4) A more satisfied and stable labour force"

Jan 1, 1950

By Garnet T. Page

"ABSTRACTThese societies •can help in such aspects of a vocation.al guidance program in secondary schools as: provide vocational and technical information, and assist with vocational exploration, such .as plant visits, films, etc. -as .an aid to the student in making a self-inventory. Evidence is increasing that employers' needs for engineers and scientists will not be adequately met in the future. Therefore, the E.I.C., C.I.M., .and C.I:C. recently revised and extended the activities of the Canadian Counselling Committee on Engineering and Science. This co-•operative .action is to be integrated with the educational system, nationally .and locally, and with provincial associations •of engineers and other groups interested in the provision of vocational information in engineering and science.DEFINITIONTHE scientific treatment of any subject requires consistent use of carefully defined terms. The National Vocational Guidance Association of the United States studied the problem of the definition of vocational guidance for .about 16 years, and in 1937 finally arrived at:""Vocational guidance is the pro-cess of assisting the individual to choose an occupation, prepare for it, enter upon and progress in it. It is concerned primarily with helping individuals make decisions and choices involved in planning a future and building a career -decisions and choices necessary in effecting satisfactory vocational adjustment.""RANGEAs a school enterprise, vocational guidance begins at that point in the individual's life when he finds it necessary to make choices that have a definite significance for his future vocation."

Jan 1, 1952

By L. Tong

"The oxidation of Quebracho was evaluated by acid-butanol assay, which indicates depolymerization of Quebracho. Anthocyanidin, an oxidation product of Quebracho, is stable at 95?C for up to 2 h. The ionization, complexation, and oxidation properties of Quebracho were discussed. Complexation of metal-Quebracho occurs at ambient temperature. The formation of complex precipitates is influenced by the acidity of the solution. Temperature is another important parameter that influences the oxidation and the complexation of Quebracho. Quebracho-ferric complex precipitate forms at 90?C, 0.1 mol/L H2SO4. The formation of Quebracho-metal complex in the leach solution is a possible reason for the consumption of Quebracho. Quebracho molecules adsorption on the mineral surface is reduced by consumption of Quebracho, resulting in poor sulfur dispersing effect in the leaching process. INTRODUCTIONQuebracho is used as a sulfur dispersing agent (SDA) in the pressure leaching of zinc concentrate as stated in U.S. Patent No. 3,867,268 (1975). It prevents the zinc sulfide particles from being coated with molten sulfur, thus preventing the inhibition of the zinc leaching reaction. Recently, the sulfur dispersing effect of Quebracho was investigated in the oxygen pressure leaching of nickel concentrate. The oxygen pressure leaching of pentlandite can be represented by reactions 1-3."

Jan 1, 2012

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005

By José Carlos Marques

This paper addresses recent calls to study the role of the state in private regulation. Using an historical, organizational-field approach, I trace and explain the evolution of public debates and interaction of different forms of regulatory initiatives dealing with Canada?s mining industry. The empirical evidence presented calls attention to the interaction amongst different regulatory forms, as well as the conditions under which the state will encourage fragmented initiatives, rather than facilitate and catalyze regulatory strengthening and consolidation. As such, my analysis: problematizes the underlying assumptions used as a starting point by the growing literature on the role of the state in private regulation; connects and juxtaposes recent scholarship to more established literature on regulatory state failure and self-regulation. I also contribute to the discussion on Canada?s CSR policy, outlining the likely regulatory effects of the current policy framework.

Aug 1, 2013

By S. Gheibi, H. S. B. Duzgun, N. Dadashzadeh

It is widely recognized that there are various uncertainties in the analysis of rock slope stability owing to inadequate information for site characterization and inherent variability and measurement errors in geological and corresponding parameters. Therefore, reliability-based approaches that allow the systematic and quantitative treatment of these uncertainties have become a topic of increasing interest in rock slope engineering. There has been extensive reliability analysis of rock slope stability in the literature. However, all of these analyses are based on the First-Order Reliability Method (FORM). The probability of failure of a rock slope in the First-Order Reliability Method is provided by a linear approximation of the failure function. The FORM is most commonly used because it is efficient; its accuracy, however, deteriorates when the nonlinearity of limit-state function increases. A better approximation of the failure function can establish a more accurate value of the probability of failure. The Second-Order Reliability Method (SORM) overcomes this drawback with a cost of lower efficiency in terms of the number of function calls and computation expenses. Despite considerable studies of the application of the SORM in other engineering fields, a few attempts have been made in the slope stability studies. In this study, a recently published Second-Order Reliability Method with First-Order Efficiency (SORM-FOE) is implemented on a selected rock slope in Amasya, Turkey. The SORM-FOE overcomes the low efficiency of the SORM by decreasing the number of function calls. The probability of failure of both FORM and SORM-FOE are obtained and the results are compared. It is shown that, in high value of failure probability, SORM’s do not significantly affect the analysis and design. However, in very low failure probability, the discrepancy between FORM and SORM-FOE becomes pronounced. It is also shown that, where the second order methods are required, the SORM-FOE is more efficient than the conventional curvature fitting methods in terms of computational costs.

Jan 1, 2015

By G. C. Hambleton

"The author has had wide experience in the reclamation of coal from coal mine waste dumps in the United Kingdom.The paper includes such topics as the processing decision and factors affecting processability; method of testing and appraisal; test data interpretation; historical influences in apppraisal; special contaminants and processing difficulties; methods of treatment; review of systems in use and their comparative economics; over-all system economics including excavation, handling methods, recovery system and shale disposal; effluent treatment; environmental considerations; alternatives to processing for coal recovery; light aggregate and cement usage; burned shale heaps; land reclamation; shale deposition for encouragement of vegetation by natural or artificial means; use of tailings fines; the environmental argument for action."

Jan 1, 1972

By O. Lashkari

Manipulation of pouring temperature is an efficient way to produce different microstructural features. In order to characterize the microstructure of rheocast billets due to different superheats of 615-695 °C, the parallel plate compression method was employed. Foundry 356 Al-Si alloy with different morphologies of primary a-Al particles were tested at different initial pressures of 4,8, 11,2 KPa, The resulted strain-time graphs were further treated mathematically to calculate viscosity of SSM billets. The interrelationships of viscosity, the microstructure and primary phase flow during compression are discussed, It is shown that the dendritic primary a-Al structure has the highest viscosity number which is almost three orders of magnitude greater than those for globular morphology, The current research have, for the first time, shown the validity and reliability of "parallel plate compression viscometry" method in characterizing microstructural evolution of Rheocast SSM billets.

Jan 1, 2005

By I. M. Marshall

SOME years ago the writer had the opportunity to plumb a number of mine-shafts, each of which presented various conditions and difficulties. This afforded the chance to compare several methods of shaft plumbing in the light of ease and rapidity. This comparison led to the development of an adaption of the Weisbach, or approximate alignment, method, to three wires in a single shaft. Professor Weisbach, some time prior to 1850, introduced his method of shaft plumbing by triangulation on but two wires, and was the first to show that a triangle of very narrow shape is the best for this purpose. THE WEISBACH METHOD The two-wire method, using a Weisbach triangle, is described in several .English text-books on mine surveying and is used frequently in various parts of the world, but in Canada it is almost unknown. The writer has described an example of this two-wire method (1), but a brief resumé here may clarify the explanation of its application to three wires. In this two-wire method, instead of endeavouring accurately to align the instrument with the wires, it is set only in approximate alignment, and the small angle formed at the instrument is measured. This is expressed graphically in Figure l, where C represents the position of the instrument and A and B the positions of the wires. The sides of the triangle are measured as well as the angle ACB, and the angles at B and A are found by applying the Sine Rule or the formula

Jan 1, 1938

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By B. Holaday, H. McLaughlin

Orano Canada Inc. (Orano) operates the McClean Lake mill, located in the Athabasca Basin region of northern Saskatchewan. It processes high concentration uranium ore, delivered in slurry form from the Cameco Corporation operated Cigar Lake mine. After the ore slurry is leached at the McClean Lake mill, the leach residue solids are washed in a process known as counter-current decantation (CCD). This process uses six thickeners to facilitate counter-current washing of solids with diluted acid, flocculation and settling, as well as pumping the washed leach residue to the tailings neutralization circuit (TN), and the uranium laden aqueous to the solvent extraction circuit (SX). Challenges in settling the slurry in CCD started in early 2017. This is largely due to the variation in fines content of the slurry (D80≤75μm), and clay content. There are several changes that have allowed the mill to adapt to the evolving challenges of settling leached Cigar Lake leach residue. Flocculant selection and mixing, temperature effects, bed level management philosophy, and centre-well feed density are key parameters that have been explored as part of adapting to changes in Cigar Lake ore quality.

Jan 1, 2020

By J. M. Livingstone

"This paper covers some of the problems confronted by Canada's railways in moving bulk materials from their source to the dock-site. The ""cost center"" concept is presented, and hypothetical examples of its use given. Also discussed are systems design, the unit train and pipelines.INTRODUCTIONCANADA LIVES BY RER EXPORTS and the Port of Vancouver by the exports of the Mountain and Prairie Empire at her back. The most recent estimates of off-shore shipments of bulk from the Port of Vancouver rise to 35.8 million shipping tons in 1985 and deep-sea general cargo estimates, in and out, are estimated at 7.6 million shipping tons for the same year. This compares to 7.67 and 2.87 million shipping tons, respectively, in 1965."

Jan 1, 1968

By C. R. Tang

Due to the current lack of sufficient occupational hazards supervisory staff in China, an occupational hazards supervision regulatory framework is proposed, based on the cloud. Data on respirable dust, noise, heat, toxic and hazardous substances and protection facilities are uploaded to private cloud computing data and service centers to build an occupational hazards supervision system. This system promotes occupational hazards governance. Complex reports are generated. Through the establishment of an occupational hazard supervision data threshold, the dynamic regulation of occupational hazards is accomplished. The main characteristics of this approach are low cost, ease of expansion and maintenance, and strong performance.

Aug 1, 2013