Search Documents

By Fridrik J. Kristjansson, Stephen R. Hicock

"Three varieties of till are recognized in the Beardmore-Geraldton area: local lodgement till, nonlocal carbonate till, and local supraglacial till. The local lodgement till unit is examined in detail for the first time in this paper. It is the best potential overburden exploration medium for gold and other metals because its particles were locally-derived and deposited subglacially, probably within a few kilometres downglacier (southwestward) from their sources, and have not been diluted by distantly-derived glacialdebris. Both local tills are richer in gold and other metals, relative to nonlocal carbonate till. Local lodgement till rests on bedrock and was encountered frequently at or near the surface in thin drift/bedrock terrain (a widespread terrain type within the west half of the study area), and commonly at the base of boreholes in thick till terrain.INTRODUCTIONDrift prospecting in areas of glaciated terrain has been well documented (in a variety of journal publications and symposium volumes; e.g . Strobel and Faure 1987; MacDonald and Mills 1988) and has proven valuable especially where overburden thicknesses hinder traditional exploration techniques. Drift prospecting techniques may well prove valuable in the Beardmore Geraldton area. This applies especially to the Wildgoose Lake Turkey Lake area where a thick and laterally extensive sheet of nonlocal carbonate till has impeded conventional mineral exploration programs (Fig. I; note the lack of gold occurrences around Wildgoose Lake).Till in .particular has been cited as the best prospecting medium among the various types of glacial sediment (e.g. Shilts 1984). Three end member till varieties are recognized in the study area: (I) local lodgement till which rests directly on bedrock; (2) non local carbonate till; and (3) local supraglacial till which occurs predominatly within, or just downglacier of, upland areas where it commonly mantles the other till varieties. Previous authors have documented how the non local carbonate till hinders gold exploration (Geddes and Kristjansson 1986; Karrow and Geddes 1987; Kristjansson 1986; Hicock 1986, 1987a, b, 1988; Kristjansson and Thorieifson 1987; Thorleifson and Kristjansson 1987, 1988a, b) and why the local supraglacial till may be a good unit for prospecting (Hicock 1986). One detailed surficial geology map sheet of the area has been published (Kristjansson et al., 1988) and others are in preparation. Closs and Sado (1981) reported on the geochemistry of soils and glacial sediments in the west half of the study area. This paper documents the local lodgement till unit and demonstrates why it is the best overburden unit to use for drift prospecting."

Jan 1, 1989

By G. D. Bysouth, G. Y. Wong

"The Endako molybdenum deposit is located 160 km west of Prince George, British Columbia. It occurs within the main body of the Francois Lake Intrusions, a composite batholith consisting of early, middle and late intrusive phases. The ore deposit is confined to Endako Quartz Monzonite, a middle phase intrusion, which is bound on the north by Carey Alaskite and on the south by Francois Granite, both late stage intrusions. In the mine aretz, the Endako Quartz Monzonite has been intruded by pre-ore dikes of quartzfeldspar porphyry and porphyritic granite, and by post-ore dikesof basalt.The Endako deposit forms a west-northwest trending body that has a strike length of 3360 m and an apparent width of 370 m. It consists of four structurally distinct zones: Endako East, Endako West, Denak East and Denak West. Principal sulphide minerals of the deposit are pyrite and molybdenite, accompanied by magnetite and minor chalcopyrite. Galena, associated with wulfenite and bismuthinite, occurs in some ores of Endako West and Denak as minute inclusions in molybdenite. The sulphides and associated minerals are hosted by quartz veins which occur principally in vein systems. Hydrothermal alteration accompanying ore mineralization has pervasively kaolinized the quartz monzonite host rock, and has locally produced K-feldspar and quartz-sericite-pyrite envelopes on quartz veins.Primary structural controls of the deposit are southwesterly dipping vein systems which strike 110° in the Endako zones, 110° to 130° in Denak East and 170° in Denak West. Secondary structural controls are northeasterly striking vein systems that dip northwesterly in Endako East and southeasterly in Denak. Domal uplift accompanying the rise of latest stage magma is considered to have caused intense dilatant deformation along older west-northwest trending shear zones, producing an elongated structural host for ore deposition."

Jan 1, 1995

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

By Gonzalo Mato, Colin Godwin, G. Ditson

"The mid-Cretaceous Seagull batholith intruded Mississippian sedimentary and volcanic rocks and Jurassic(?) granitic and ultramafic rocks within the Omineca Crystalline Belt in the Yuk on Territory near the British Columbia boundary. Leucoerotic fluorine- and boron-rich granites of the batholith exhibit many textural variations from aplite to pegmatite, but are dominated by a coarse-grained seriate unit and a fine-grained porphyritic unit.Four distinctive tin vein occurrences within and near the batholith are described, the most interesting of which is the MC showing of quartz-calcite-chlorite-cassiterite veins in intensely fractured zones of sedimentary and volcanic rocks. Three other showings occur within the batholith:J) the EC showing of quartz-fluorite-cassiterite-sulphide veins with prominent muscovite-illite alteration;2) the DU showing of quartz-hematite-fluorite-sulphide- sulphide-cassiterite with considerable manganese staining and sericitic alteration; and3) the VAL showing of quartz-tourmaline-cassiterite-fluorite-arsenopyrite veins with little associated alteration.Most cassiterite occurrences are within easterly-trending, vertical structures and all occurrences are thought to represent parts of a single system. These mineralogical and physical variations are apparently related to the distance from the upper contact of the batholith.For the Seagull batholith, Rb-Sr isotopic data give a 100±1.4 Ma isochron age that is concordant with the K-Ar model age from biotite of 101±4 Ma. Initial Sr isotopic ratios for the batholith are high at 0.712, indicating an old, sialic crustal source for this pluton. This initial ratio is similar to values for granitic rocks associated with tungsten deposits in the Yukon Territory. The high initial ratio for Sr, the high Si02 content, the high s/I index, the presence of normative corundum. leucogranitic composition and associated lithophile-tungsten mineralization demonstrate that the Seagull batholith is probably an S-type granitic body. This factor is significant to regional exploration jar tin and tungsten in the Canadian Cordillera."

Jan 1, 1983

By L. S. Jen

Canadian copper, nickel, zinc, lead and molybdenum mines are characterized by the mining of ores from which more than one metal is recovered. During the 1980s, approximately 15% of the gold, 25% of the zinc, 30% of the copper, 55% of the molybdenum, 80% of the silver and 90% of the lead produced from Canadian mines were produced as co-products and by-products of base metal mining operations. This trend is not expected to change significantly in the near future. The presence of co-products and by-products affects the level of production and the level of revenue from base metal mines in several ways: (I) in general, production of one base metal cannot be expanded or cut back without affecting the amount of production of another metal;(2) the commercial success of certain base metal mining operations depends on the substantial bonus revenues from co-products and by-products; (3) the quality and economic viability of many ore deposits are significantly improved by the presence of co-products and by-products; and (4) while coproduction is critical to the survival of some mines, bonus revenue from by-products can also be life saving to others during economic downturns. For these reasons, deposits with significant co-product or by-product values are likely to continue to be significant targets for exploration and for acquisition.

Jan 1, 1992

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By G. W. Poling, G. W. Hawthorn

"""Unassayable gold and platinum group metals"" have come into vogue in the 70sand 80s in certain jurisdictions as a means of perpetrating fraud. Usual arguments are that a particular ore is not amenable to ""conventional fire assaying"". Explanations for unassayable gold usually revolve around: evaporation of micron-size gold; vaporization of organic gold complexes; volatization of gold halides; alloying of gold with PGM's which prevents fusion or alloying which prevents collection .This paper reviews several of the myths and truths of gold and PGM assaying with the knowledge that not a single mine operatesin thefree world producing gold from unassayable ore.INTRODUCTIONAccurate analyses of exploration data and estimation of ore reserves are two of the most important functions of professional geologists and engineers in mine development. The problems encountered become particularly acute when dealing with precious metal values where very low grade deposits (in the range of 0.0 I Troy oz per ton or - 0.2 ppm (g/t) by weight) sometimes are economic or constitute ""ore"". To emphasize this ""scarcity effect"", a gold assay of 0.4 g/t (0.01 T oz/st) would result from the presence of a single 420 J.tm (35 mesh) gold flake (which weighs I milligram) in a 5 kilogram siliceous sample.The current high gold price and the prospects of high profit margins awaiting exploitation of even very low grade gold deposits, has spawned a sizeable group of incompetent or fraudulent gold assayers. These ""assayers"" will often report significant precious metal values where no such values occur. Failures of legitimate assay labs to confirm these ""significant"" assays are often attributed, by the charlatan, to their capability of detecting ""unassayable gold"" while the check assayer cannot. Geologists and engineers lacking detailed knowledge of sampling and assaying techniques are often hard-pressed to convince a gold-fever aroused company executive or investor-client to abandon a property on which attention-grabbling values have been reported, often by more than one laboratory. Professionals engaged in such evaluations must acquire an understanding of contemporary precious metal sampling and assaying techniques . Only then can they determine whether misrepresentation of values have been perpetrated"

Jan 1, 1989

By Denis Beaudoin

Program Basics: Goals, Course Content & Training Process Sudbury: History of the Program & Lessons Learned Diavik: History of the Program & Lessons Learned Most Recent Program: Totten Mine in partnership with Sagamok Anishnabek Summary -Lessons Learned Conclusion

Oct 1, 2010

By K. Barron

"A computer program is described which will analyze the stability of coal pillars. The extent of the peripheral failed zone and the central elastic core of the pillar, the stress distribution across the pillar and its strength can be determined by a ""sliceby- slice"" analysis technique. The program incorporates a brittle/pseudo-ductile transition point so that a pillar may fail by brittle fracture or pseudo-ductile yield. It is shown that:(i) There is a minimum pillar stress below which fracture cannot initiate; hence there is a minimum pillar strength. (ii) In specific circumstances (narrow pillars) , once fracture initiates at the pillar edge it must propagate immediately to the pillar centre. This unstable situation is called ""catastrophic"" failure and might be regarded as a model of a pillar ""burst "". (iii) For wider pillars, the failed zone ex tends gradually into the pillar as the loading increases until it reaches the pillar centre when the pillar is deemed to have f ailed. This is called the point of ""ultimate"" failure.The critical pillar widths to avoid catastrophic and ultimate failure can be calculated.A hypothetical analysis of five rib pillars is given to illustrate the application and the results obtained from the model. The model is then used to analyze three case histories taken from the literature. The first demonstrates the applicability of the brittle/pseudo-ductile failure criteria for Pittsburgh coal. The second compares the pillar strength formulae derived here with those of Salamon and Munro(13) and Bieniawskiou . The final case history compares the model analysis with field stress measurements in a yielding pillar. In all cases the model results are compatible with the case histories."

Jan 1, 1984

By F. Boudreault, C. Hendricks, M. Scobie

Drilling accuracy represents an important quality control factor in minimizing dilution. Apart from geology, the factors governing drilling accuracy are largely within the control of the mine. Setup location and alignment, as well as actual drilling accuracy, can all be monitored toward their improved control. Trajectory deviation during drilling, although usually beyond the control of even the most experienced and conscientious driller, can be accounted for (if not full controlled) by down-hole surveying of blastholes prior to explosives loading. This paper reviews the available instrumentation for improved drill setup and recent field experience with several commercial systems designed for monitoring borehole deviation. It reports on a recent survey of 50 Canadian mines which use blasthole stoping and addresses the reasons for the apparent lack of interest in instrumentation: i.e. does this reflect a lack of awareness of the technology, perceived inadequacies in its performance or a predominant reliance on productivity (drilling and mucking) as a measure of operational efficiency? The survey findings supported the latter viewpoint and showed that very few Canadian mines operate drilling incentive programs that are related to drilling accuracy.

Jan 1, 1994

By Ross G. Bertinshaw

"The Line Creek Mine of Crows Nest Resources started mining coal in the fall of 1981. There are seven mineable seams with thicknesses ranging from 1.5 to 13 metres and with dips varying from 0 degrees to 60 degrees. This, together with internal partings and the very friable nature of the coal, creates a number of mining problems.The coal is divided into zones depending on the dip of the seam. Each zone requires a different mining technique to ensure optimum recovery and low dilution while still keeping fines to a minimum.Line Creek employs a combination of hydraulic front shovels and backhoes to mine its coal without blasting or use of dozers. This has been very successful in reducing the proportion of fine coal hauled to the plant, thus improving quality control and reducing costs in coal processing.There have been a number of other benefits from the use of excavators instead of more conventional methods. These include better selectivity, good cleanup, reduction in traffic at the face and lower cost.IntroductionThe Line Creek Mine is situated approximately 25 km north of Sparwood in southeastern British Columbia (Fig. I). Preproduction stripping began in J98J with the first coal shipments made in 1982. In 1983 the mine produced 2.1 million tonnes of raw coal.Similar to other East Kootenay coals, the seams at Line Creek are characterized by their friability, producing a large proportion of fine coal during mining. In an attempt to reduce these fines Crows Nest Resources has instituted the use of hydraulic excavators to mine and load the coal.Hydraulic excavators offer other substantial advantages over front-end loaders and dozers, which has been the conventional system in other mines in the area."

Jan 1, 1985

By M. Sugamata

Creep tests were carried out for friction welded joints of AZ31 magnesium alloy rods under an ambient atmosphere at temperatures between 423 and 573K. Tensile tests were also performed at temperature from room to 573K. The obtained results were compared with those of the base metal. AZ31 extruded rods of 19 mm in diameter were joined by brake type friction welding machine. Creep and tensile specimens were machined out of the welded rods. The tensile strength of the joints was almost the same as that of the base metal at room temperature. However, joint efficiencies of welded joints were about 92% at above 373K. The elongation of welded joints was lower than those of base metal. The welded joints showed appreciably higher minimum creep rate and shorter rupture time than the base metal at all the tested temperatures and initial creep stresses. Creep and tensile rupture of the joints always occurred at near the weld interface. Thus, friction welded joints of AZ31 alloy showed lower creep and tensile strength than the base metal at elevated temperature.

Jan 1, 2006

By F. T. Manns, G. Harper

"The Swayze gold mine is an Archean vein deposit in northern Ontario. The veins are superimposed on a conjugate joint system and are contained within an anastomosing alteration envelope in a metadiorite body. Reserves were estimated on the basis of fire assays of channel samples and car load samples from underground mine openings, surface and underground diamond drilling and surface trenching. A semi-variogram constructed from channel samples along one of the drifts yielded a horizontal, regionalized influence of approximately 9.0 m. Common industry practice has been to use 6.1 m for similar deposits in Ontario. Proven ore was defined from underground openings. The maximum extrapolation distance for proven ore along strike and dip from a data point is taken to be 6.1 m. Probable ore is extrapolated 7.6 m from a data point in a mine opening or from a drill intersection. Possible mineralization is based on geological continuity one-half the distance to a neighbouring data point.The mineral inventory estimate of 1.45 million tonnes at a grade of4.8 g Au/tonne gives an excellent outline of the geology of the deposit. The deposit contains 313 000 tonnes of ore reservesat a fully diluted grade of6.9 g Au/tonne. These figures include dilution for several reasons: (I) a 2.1 m mining width is used rather than the more typical 1.5 m width to allow for over break because of the shallow dip of some vein zones; (2) over break is allowed for adjacent to major unmineralized dykes; and (3) grams of gold are deleted from estimates to allow for the mining of unavoidable minor dykes.A personal computer with off-the-shelf software was used to compile 712 geologically defined ore blocks and sort them into a number of revealing categories. The computer was used to perform grade sensitivity tests, as well as to evaluate depth potential. Hopefully, the reiterative aspect of the method has randomized the errors and helped to cancel their effects."

Jan 1, 1987

By G. H. Hope, A. R. Maycock

"La Mine Doyon is a gold mining operation located in northwestern Quebec, approximately 35 km east of Rouyn-Noranda and 85 km west of Val d'Or. The mine is jointly owned by Lac Minerals Ltd. and Cambior Inc. with Lac Minerals as the manager. Production statistics as of February 1987 are 6.4 million tonnes milled at an average grade of5.8 g/t Au. Current reserves of9.9 million tonnes at 5. 7 g/ t Au to a depth of400m have been outlined. Indicated reserves below this horizon could considerably increase this reserve.The mine currently consists of two open pit and two underground mine operations, producing approximately 3600 tonnes per day of ore at an average grade of6 g/t. The ore is currently processed at the La Mine Doyon mill at a rate of1400tid and at Lac's East Malartic mill at 1950 t/d. Ore is also processed intermittently at Lac's Les Terrains Auriferes mill and at Noranda's Horne Division.La Mine Doyon is currently in the midst of a program to expand and upgrade the mill at La Mine Doyon. The expansion to 3000 t/day includes the conversion of the existing crushing and grinding circuits to a SAG (semi-autogenous grinding) mill circuit and the existing filter wash plant to a CIP (carbon-in-pulp) recovery plant. The economics of this project are based on reduced operating costs (milling and trucking) and improved recovery due to updated technology. HistoryThe area between Noranda and Val d'Or has a long history of mining activity in both base metals and gold, dating back to the early 1930s. More recently, several new orebodies have been discovered and exploited in the area including La Mine Doyon, Lac's Mine de Bousquet, Dumagami, and the Kiena operation.La Mine Doyon was discovered in the early 1970s, and brought into limited production in late 1979. The mine was started on are reserves of 2.75 million tonnes at 6.2 g/t and was, thus, considered a small, short-term operation. Mining started at an initial rate of 550 tI d with all the ore being shipped to Noranda's Horne smelter as flux. When Lac's East Malartic mill became available for custom milling, Doyon commenced shipping to that facility at a rate of 650 t/d. As a result of some equipment additions and an improved understanding of the ore, the East Malartic mill throughput was gradually increased from 650 t/d to the current rate of 1950 t/d."

Jan 1, 1988

By Eugene F. Mehr, Dennis C. Martin

"Development of the final slope for the 340 m (1200 ft) high hanging wall at Cassiar Mine precipitated an area of deep seated instability involving an estimated 17.6 million tonnes. The deformation mechanisms involved squeezing of soft deformable serpentinite rocks in the toe which caused planar sliding and graben toppling of the stronger sedimentary rocks in the middle and upper sections of the slope. Although movement rates up to 150mm/day were recorded, by understanding the controls on failure, the mine was able to install a suitable monitoring system and complete the open pit with only minor loss of the mineable ore. Accelerated mining was required in the last full year of operation. This paper describes the deformation behaviour, failure mechanisms and back analysis results for the failure. The monitoring systems and operational aspects related to the failure are also presented.IntroductionCassiar Mine is located in steep mountainous terrain in northern British Columbia approximately 1200 km north of Vancouver (Fig. I). During the final mining phase of the open pit, instability developed in the approximately 340 m high hanging wall (east wall) slope. A unique graben toppling mechanism was identified based on detailed assessment of slope monitoring data and visual observations. Comprehensive slope monitoring enabled mining to continue even though movement rates as high as 150 mm/day were being recorded. Three-dimensional limit equilibrium back analyses and numerical modelling have been used to assess the various controls on the slope movements and to understand the failure mechanism."

Jan 1, 1993

By Eric D. Jamieson

"How well is the Canadian coal industry able to expand in the tough competition with other fuels in Canada and with other suppliers in the international, metallurgical and thermal coal trade? Coal production as a whole decreased between 1950and 1960 and, although there has been a tripling of production since then, underground production continued to decrease until 1975. This trend has been reversed to a certain extent as a result of the modernization of mines in Cape Breton, but in 1978 over 85% of coal production came from surface mining.Against this background, the paper reviews current Canadian mining operations as described in papers presented at the 1979 CIM Annual General Meeting. Conclusions are then drawn regarding some of the longer-term mining applications in relation to the latest coal demand forecast, which indicates a potential Canadian production requirement of 160 million tonnes per year by 2000. IntroductionThe Canadian 'coal industry is experiencing a period of expansion and a new record for production is set with each passing year. This growth pattern over the last IS years has been based on two main markets-the generation of electricity in Canada and the export of coking coal to Japan. Supply to those markets has entailed either the development of mining, coal preparation and transportation systems for the delivery of large volumes of products with predetermined specifications or the establishment of minesite plants designed specifically to suit the characteristics of the coal in the adjacent deposits (Fig. I).Coal is a low-value commodity in relation to its bulk, and the economics of coal use become progressively less attractive with increasing distance from the producing mine. The transportation component in the export trade and in the movement of western coal to Ontario is a major cost factor. In the latter case, it approaches the cost of coal produced at the mine. In addition, the .international competition among coking coal producers chasing diminishing markets in a worldwide steel recession as well as the competition from U.S. coals and other fuel s for Canadian thermal coal have introduced a tight set of parameters to govern mining practices in all parts of the country. Some appreciation of the required changes in mining techniques brought about by declining traditional markets and the rigorous demands of the new bulk markets can be gained by comparing production from surface and underground mines over the past 25 years (Fig . 2)."

Jan 1, 1980

By Nirmal Weerasekara, Lian X. Liu, The University of Queensland, Weiguo Xie, Benjamin Bonfils, Ping Yu

A mill model structure based on the population mass balance framework incorporating breakage characteristics, slurry and solids transport, product classification and discharge and energy consumption was reported in XXVII IMPC and named the Generic Tumbling Mill Model Structure Version I (GTMMS I). In this work, a new 4D (four dimensional) appearance function sub-model based on the experimental results of the JK Rotary Breakage Tester (JK RBT) was developed to describe the breakage characteristics and was applied to this new model structure. The newly developed 4D appearance function model has fewer fitting parameters and is more generic in nature. Most importantly, it is applicable to both high and low energy impact breakage. It is therefore much more versatile in comparison to the existing JKMRC t10- tn appearance function and the size-dependent JK M-p-q t10-tn appearance function. In addition, the Discrete Element Method (DEM) energy distribution model was integrated into the new model structure. With DEM results providing energy distribution information inside the mill directly, the selection function and the back-calculation method used in the existing JKSimMet modelling method are not needed in this model structure. With the above two revolutionary innovations, the previous model structure was upgraded to the Generic Tumbling Mill Model Structure Version II (GTMMS II). Furthermore, the new model structure is dynamic in nature with time-stepping technique for non-steady-state simulation. A case of the dynamic grinding of a SAG mill was studied to validate the GTMMS II. The model simulation results agreed well with the plant data. With the newly developed 4D appearance function model, the incorporation of DEM energy distribution and transport function, the GTMMS II is an important step forward towards mechanistic modelling of tumbling mills.

Jan 1, 2016

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995