Search Documents

By C. Langer

Although the existence of precious metals, particularly those of the platinum group, in the nickel ores in the Sudbury district has been known for a good many years- almost as long as the ore deposits themselves- the Mond Nickel Company were the first to effect their recovery on a commercial scale. The precious metals values of the different Sudbury ores vary considerably, and are generally higher in the copper-rich ores. These values are so very small that a direct determination in the ores gives quite unreliable results. This is not surprising if one considers that some of the ores contain on1y one unit of total precious metals in about two million units of ore, and that this one unit will consist of seven different metals, each with a different chemical behaviour. It is only after the ores have been smelted to a Bessemer matte containing about 80 per cent combined copper and nickel that the precious metals content can be determined with some degree of certainty. From the figures thus obtained, the precious metals content of the ores can be calculated, provided the tonnage of ore used to produce one ton of matte is known. The recovery of these minute quantities of precious metals out of ?such a large amount of gangue and sulphides of iron, copper, and nickel seems at first glance a commercial and technical impossibility. Nevertheless, science has found a way to conquer all the difficulties, and quite substantial quantities of the precious metals contained in the Sudbury nickel-copper ores have been regu1arly recovered for many years by the Mond Nickel Company.

Jan 1, 1927

By Karl J. C. Harries

"7.1. INTRODUCTIONThis chapter addresses the joint venture and examines a number of general concepts of the joint venture relationship. Chapter 8 looks at some specific concepts related to the provisions of a joint venture agreement, which are equally applicable to a shareholders’ agreement or other contractual relationship. The term “joint venture” is used because the author is a common law solicitor (a matter of convenience for which apologies are offered to civil law readers), but it should be noted that, in many aspects, the legal structure of an entity is irrelevant. It is the relationship of the parties, be they venturers or shareholders, that is important, and the areas of concern are surprisingly similar (except for terminology).The details of the joint venture relationship and agreement could fill several books. Accordingly, this chapter and the next focus on selected topics that appear to have caused problems or confusion or to be the basis for disputes. And remember that, although the following discussion is in the context of a joint venture, many of the comments apply, either directly or indirectly, to virtually any common undertaking and the agreement defining it.For interest’s sake, this chapter starts with a summary of some of the earlier types of agreements and arrangements that have evolved into the joint venture agreement of today in Canada, the philosophy of their format, and the reasons for their demise.7.2. EVOLUTION OF THE CANADIAN JOINT VENTUREThe Early DaysMuch of the opening up of Canada’s north is due to exploration for and development of mines. The early discoverers were relatively free to roam and explore at will and, if they were fortunate enough to find something, they dealt with the appropriate government to acquire exploitation rights. The early interests lay in gold or silver. Workings were small, usually worked by the owner alone or with only a couple of helpers to extract the native gold or silver. If the owner wanted to move on, he could sell his property outright and use his stake to look elsewhere.As logging and mining camps were opened, the development of better roads and railways made access easier. Entrepreneurs saw the opportunity to make money by assembling large parcels of land and working them as a single operation. In order to do this, some owners who were not ready to sell out had to be convinced to do so through more attractive offers"

Jan 1, 2003

By Ram Song, Yohei Harada, Shinji Kumai, Kazuho Otsuka

"Recently, vertical-type high-speed twin-roll casting (HSTRC) has been developed. The HSTRC shows extremely high cooling rates over 1,000 K/s even at the mid-thickness area. The fabricated strip has many metallurgical characteristics; super-saturation of alloying elements, fine solidified structure, and homogeneous distribution of fine constituent particles. In Al-Mn based alloys, the Mn alloying element can be supersaturated in the a-Al matrix and also form Mn-containing constituent particles during solidification. The Mn supersaturation and the distribution of primary/secondary particles in cast products affect the metallurgical behavior in the down-stream processing and can improve mechanical properties of the final products. In this study, Al-Mn based alloy strips were fabricated by HSTRC with various Mn contents. The solidified microstructure, constituent particles and its distribution, and Mn solubility were investigated in the as-cast condition. Due to the high cooling rate of HSTRC, fine constituent particles were homogeneously distributed, and coarse intermetallics were not observed. Mn solid solubility was estimated by electrical conductivity. The estimated Mn solubility was equivalent between strip surface and mid-thickness area.INTRODUCTION Al-Mn based alloys, as non-heat treatable wrought aluminum alloys, are widely used in packaging and heat exchanger for automobile industry. Besides Mn, Al-Mn based alloys often contain Fe and/or Si as alloying elements or natural impurities. During solidification, Mn can be super-saturated in the Al matrix, and also form Mn-containing constituent particles. Additionally, in the subsequent thermal-mechanical processes such as homogenization, rolling, and intermediate annealing, Mn in solid solution precipitates out of the Al matrix as secondary particles. The size, distribution, type, and the amount of dispersoids including constituent particles affect to texture evolution, recrystallization behavior, and final mechanical properties of wrought Al-Mn based alloys (Huang et al., 2016; Huang & Marthinsen, 2015; Engler et al., 1995; Muggerud et al., 2013). Therefore, controlling the initial level of Mn super-saturation and the distribution of constituent particles are important in the cast Al-Mn based alloys."

Jan 1, 2018

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By Max W. Ball

YOU have been kind enough to ask me to speak to you on "The War and Anglo-American Relations." A speaker always takes the liberty of putting his own interpretation on the scope of his subject. I am going to exercise that privilege, and try to look back over a generation of Anglo-American relationships and forward beyond the present war. I should like particularly to consider responsibilities as well as relationships. A more accurate caption for what I am going to say would be "Anglo-American Responsibilities.?? THE WAR WILL BE WON I am assuming that sooner or later we shall win this war. History and economics point to the same conclusion, that Germany has attempted the impossible and that the seeds of defeat are already sown. As to one ecof1:omic factor, I am already on public record as believing that Germany's oil supply is inadequate for the war she has launched. That opinion is unchanged. Aside from such tangible factors, moreover, I am convinced that the spirit of freedom is unquenchable, and that no combination of powers will be able to rout it from the British Commonwealth of Nations and the United States. Stronger even than this conviction is my faith in a God who will not suffer the defeat of man's aspiration to be master of his own soul. I am sure that all of you share that faith, and that we need not argue it. We can start with the assumption that the war will end in victory. The subject we are to consider, then, is the relationship of the English-thinking peoples during the conflict, and their joint responsibilities in the difficult days that will follow it. A CANADIAN-AMERICAN No talk on such a subject is worth listening to unless the audience knows the background and fundamental beliefs of the speaker. No human statement stands alone; behind and beside and within it are the ideals and the bias of the man who makes it. Because I am a stranger to most of you, I am constrained to talk about myself before I talk about more important matters. The review may be profitable, not because of the subject, but because it may illustrate the evolution of an attitude toward England.

Jan 1, 1941

By W G. Forbes

SOME 20 years ago, upon finishing second year at the University of Manitoba, I was faced with the choice of whether I wanted to be a geologist or a chemist. Accordingly, I sought out Professor Brownell, Head of the Department of Geology, to ask him what a geologist did. His reply contained the statement that following graduation one went out into the field in northern Canada for 5 to 15 years to reduce to practice what had been learned at university. To a young man, very socially conscious, even one year, let alone 5 to 10, in a small mining community sounded like being banished to a monastery in the Himalayas and thus I turned to chemistry. Moving to the present, last month I asked a geologist, and then a mining engineer, what does the fresh graduate in their field do these days? The reply was: usually serve an apprenticeship for an indeterminate period either underground or in the field learning the job.

Jan 1, 1965

By A. Gakwaya, K. Ba, M. Guillot, J. Levesque

"In the aerospace industry, parts requiring tight dimensional tolerances and high mechanical properties are often produced by forging. This forming process allows for an optimal use of the material and can produce high quality parts at a reasonable cost. Thanks to CAD techniques, it is now easier to predict flow profiles and in-process defects occurrence as well as wear of the forging dies. However, in order to determine the properties of the forged part with computer simulation methods, a good material constitutive law is a prerequisite. This paper presents a virtual manufacturing process modeling for the closed die forging of a workpiece performed with Abaqus. The hot closed die forging is a regular process applied to manufacture metallic components used in aerospace industry. In this forming process, the material flow and final properties depend on the microstructure evolution during the process that is why it is important to include the microstructure effects in the material model. Based on the stress-strain data measured experimentally, the material parameters of the standard (classical) Johnson-Cook constitutive model and of a modified Johnson-Cook constitutive law including the microstructure effects have been determined. The obtained simulation results are compared with the experimental results for validation.INTRODUCTIONDue to their good physical and mechanical properties such as ductility, fatigue strength, corrosion resistance and rupture, aluminium alloys are often used in the aeronautic and the automobile industries. In this work, we present the forging of an Al-Zn-Mg-Cu alloy, a high strength aerospace alloy recognized for his good combination of physical and mechanical properties. The forging process is simulated in Abaqus Explicit using both the standard Johnson-Cook law (Johnson & Cook, 1983; Hor, 2011; Lin et al., 2012), and its modified version as proposed by Andrade et al., (1994). The Johnson-Cook law offers the advantage of considering the coupled effect of the plastic strain, the plastic strain rate, the temperature of forging and the hardening effect. However, it is a phenomenological model which does not account for the effect of the microstructure evolution. In this work, a modified Johnson-Cook model implemented in a user subroutine is used. It includes the effect of the dynamic recrystallization phenomenon during the hot deformation. The dynamic recrystallization has a noticeable influence on the microstructure and on the properties of the material. The term dynamic means that the process starts and acts during the deformation and this is different from the static mechanism of recrystallization which occurs during an annealing and after cold or hot deformation. Since properties of the alloy used in this work are not readily available in the literature then characterization tests have been done at various temperatures and strain rates, in order to determine the thermomechanical properties and the material behavior during the process of hot forming, more precisely during the hot forging process."

Jan 1, 2016

By Renliang Shan

Site conditions of China?s coal roadways are complex and changeable, and scientific classification of them is the fundamental basis for coal roadway support design, with great significance for ensuring proper roadway service. Upon analysis of the issues, a commentary regarding the research progress on classification of the stability of rocks surrounding coal roadways in China has been achieved from the point of view of classification methods and indexes. The shortcomings and applicable scope of rock stability classification methods related to coal roadways have been analyzed. It has been asserted that combining artificial neural networks with fuzzy mathematics, combining fuzzy mathematics with grey theory, applying new avenues such as support vector machine algorithms or unascertained average classification, and making classification indexes more scientific are future directions for development of rock stability classification for coal roadways.

Aug 1, 2013

The Discrete Element Method (DEM) is a powerful tool for analysing the flow of charge, the energy consumption and the pattern of energy utilisation of a SAG mill. With the development of laser scanning measurement, the detailed internal working surfaces of a SAG mill can now be included in DEM models. Using scanned results for new and worn shell liners for a 32? (9.75 m) SAG mill, it is shown that the feed and discharge lifters have significant effect on the flow of the charge introducing significant threedimensionality. The effects of the resolution accuracy of liner geometry and the lower cut-off of the rock size distribution are explored. Finally, using a matched new and end of life worn liner and operating conditions taken from site surveys, the effect of wear on charge motion, distribution and energy utilisation are evaluated.

Jan 1, 2012

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013

By A. Proulx

Durant les années 1955 à 1961, plusieurs campagnes d?exploration ont été menées sur la zone Bond dans la partie sud-ouest de l?anneau nord de la carbonatite d?Oka (propriété de Niocan, figure 1). Les zones minéralisées HWM1 et HWM2 sont découvertes à l?ouest de la propriété. Un des forages, le S-60, avait intercepté 80 mètres de minéralisation à 0.71% Nb2O5 à l?est des zones HWM1 et HWM2 mais aucun autres travaux d?exploration n?avaient été réalisés sur cette interception minéralisée. En 1995, Niocan réalise une campagne de forage pour mieux définir la zone minéralisée recoupée par le forage S-60. En 1997, une seconde campagne de forage détermine un tonnage de 14.37 Mt avec une teneur de 0.66 % Nb2O5 pour la zone S-60 (Marcotte et Gagnon, 1997). Le complexe carbonatitique d'Oka se situe à environ 35 km à l?ouest de Montréal sur la rive nord du lac des Deux-Montagnes. Sa formation remonte au Crétacé précoce (entre 117 à 123 Ma). La carbonatite d?Oka fait partie de la suite d'intrusions alcalines que constituent les collines Montérégiennes. Le complexe a une forme allongée (7.2 km par 2.4 km) orientée NO-SE (figure 1). Il est intrusif dans des roches précambriennes constituées d?anorthosites au nord et de gneiss charnokitique au sud (Gold, 1963) appartenant à la Formation de la colline d?Oka. Les gneiss au contact du complexe sont fénitisés sur une épaisseur qui peut atteindre jusqu?à 60 mètres. Les roches carbonatitiques forment la série dominante du complexe et elles sont composées principalement de calcite (> 50 %) à gros grain et parfois rubanées. Les minéraux accessoires les plus communs sont la biotite, le pyroxène, la monticellite, la magnétite, l?apatite, la forstérite, la mélilite, le pyrochlore, la pérovskite, la niocalite, la pyrite et la pyrrhotite (Gold, 1963).

May 1, 2003

By Steven D. Botts

The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd. , is a $2.3 billion copper/zinc project, located in the Ancash Department in Perú. The project consists of an open pit mine, a 70,000 ton per day concentrator, a 302 Km. long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 million tonnes per year of copper and zinc concentrates over a 23-year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world. This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28th, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14th, 2001 by Peruvian president Alejandro Toledo. The construction stage of the project generated 8,000 direct jobs, with a peak of 10,000 employees, and 30,000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals; around 30% of whom came from the department of Ancash where the deposit is located. Approximately 5,800 indirect jobs will be generated from the project. Independent sources state that Antamina will increase the Peruvian mining exports by 30% and Peruvian GDP by 1.4% within its first year of full operation in 2002. Since winning the privatization bid for the project in 1996, the company has implemented a successful approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company?s environmental program. Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues, and as a result, has set new standards in Perú for environmental and community management, and sustainable development.

May 1, 2002

By M. J. Nicol, C. van Wensveen

The kinetics of the oxidation of thiosulfate by copper(I I) in ammoniacal solutions have been studied in the presence and absence of dissolved oxygen. The formation of an intermediate mixed ammine/thiosulfate copper(II) complex ion has been confirmed and the rate of the reaction monitored by simultaneous on-line spectrophotometric, dissolved oxygen and potentiometric measurements. The rate of the anaerobic oxidation of thiosulfate by copper(II) was found to be orders of magnitude slower than that in the presence of dissolved oxygen and is inhibited in the presence of ammonia and anions such as sulfate and chloride as a result of competition with thiosulfate for the axial coordination sites on the copper(II) tetrammine complex. In the presence of dissolved oxygen, it was found that the copper(I) thiosulfate complexes are only very slowly oxidized while the copper(I) diammine complex is rapidly reoxidised to the copper(II) state. Thus, the initial rapid reaction with copper(II) leads to a pseudo steady-state condition in which the concentration of copper(I) is relatively constant and the rate of oxidation of thiosulfate can be predicted from the measured rate of oxidation of copper(I) by oxygen in ammoniacal solutions. The effects of the concentrations of ammonia and thiosulfate on the oxidation rate can be rationalized on the basis of the above coupled to the species distribution of copper(I) in the ammonia/thiosulfate system. It is shown that, with relatively simple measurements of dissolved oxygen and copper concentrations, the rate of oxidation of thiosulfate can be predicted under typical leaching conditions.

Jan 1, 2005

By Jerry Handford

Investing in the Development of our Future Workforce ?Collaborative partnerships with educational institutions, industry associations, governments and other businesses. ?Programs: »Co-op / Discipline Student Program »Trades Development Initiatives »Operator Training Programs »General Student Program »Careers Next Generation / Community Careers Co-operative

May 1, 2006

By J. R. Maxwell

In 1970 expansion was completed increasing mill capacity from 2,000 to 3,000 T.P.D. Actual grinding capacity is 3,400 T,P,D. at a grind of 60% -200 mesh,The ore bodies are vein type, containing about 12% sulphides, with mill heads averaging 2.25% Cu, 0.015 oz.Au, and O.4O oz, Ag. per ton.Summary and Conclusions:During the period Jnnuar-1 1971 to December 1973 inclusive the use of large cells at Opeminka have shown that metallurgy is comparable to when using conventional cells, Operating and maintenance costs are lower, An on stream analyzer with reagents controlled by computer, are being assessed further.Opej1atljn Of Cells:!lo cell level adjustments are required when tonnage is adjusted 20 to 25%.Depending on mill heads and grade of concentrate reagents are adjusted to the first rougher for metallurgical control. Reagents to second rougher and scavengers are seldom adjusted as feed to this section has a maximum variation of about 0.2'~ Cu.Power – Maintenance and Space Requirement :Our total power consumption for 3,400 T.P,D. flotation circuit for operation and air supply is 280 H.P. Previous power drawn using conventional cells was 400 H.P. at 2,000 T.P.D.Total maintenance costs for flotation circuit has averaged $1,100.00 per year for the 3 years of operation, this cost should remain constant.Floor space required for cells and walkways is 2,000 sq.ft.

Jan 1, 1974

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By Hongpu Kang

The fully mechanized top coal caving mining method has been the main mining approach for thick coal seams with high output and efficiency in Chinese coal mines. The gateroads for the top coal caving mining faces should be driven along the floor of the thick coal seam with a part of the seam as roof. The support of the gateroads is commonly difficult because of the low strength and broken structures of the coal seams, and the increasingly large section of gateroads meeting the need of greater and greater face coal output. Based on the analyses on the geomechanics properties and production conditions of the top coal caving mining, the influences of the top coal caving mining parameters on the stability of gateroads, including mining thickness and face length, are studied. The deformation and damage features of the rock mass surrounding the gateroads with the top coal seam as roof are investigated, the interaction of the support with the surrounding rock mass, the support theory are studied. The bolting design method and criteria, bolting forms and parameters for the gateroads with the top coal as roof are put forward. The rock bolting components, including bolt bars, face plates, cable tendons, meshes, and steel straps, are introduced. Finally, the gateroad bolting effects are evaluated through a typical case study on the basis of field monitoring data, such as the displacement of surrounding rock mass and the forces along bolts and cables.

Aug 1, 2013

By G. M. Ross, I. M. Ross, J. A. Scott

"The otherwise waste heat in many water streams in the mining industry can be used to provide space heating of adjacent infrastructure including laboratories, workshops, and offices. This can be achieved by using heat pump systems, which can work as a replacement or in conjunction with existing space heating. In the example investigated—process cooling streams at an ore smelter—the analysis provided illustrates that annual heating costs can be 19% lower and a simultaneous 62% reduction in CO2 emissions can be achieved.RÉSUMÉ Dans l’industrie minière, la chaleur qui serait normalement perdue des circuits d’eau pourrait servir à chauffer des structures adjacentes incluant les laboratoires, les ateliers et les bureaux. Cela pourrait se faire en utilisant des systèmes de thermopompes, qui pourraient remplacer ou s’ajouter au chauffage existant. Dans l’exemple étudié, des circuits de refroidissement de procédé à une fonderie, l’analyse fournie illustre qu’il est possible de réduire les coûts annuels de chauffage de 19 % et d’obtenir une réduction simultanée de 62 % des émissions de CO2."

Jan 1, 2016

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962